|
|
Knobs |
|
|
Click on photos for
larger view |
BRASS
POT ADAPTER SLEEVE
Do you want to put a 1/4" set-screw knob on
your 1/4" knurled shaft potentiometer? Do you need to eliminate the
off-center problem when using a 1/4" set screw knob on a 6mm shaft pot?Just slip one of
our solid brass pot adapter sleeves onto any 1/4" knurled pot shaft
or 6mm pot shaft to ensure a
snug and secure fit for a 1/4" (6.35mm) smooth shaft knob. We have tested this adapter extensively, and it really does work great!
Note: Will NOT work with 3/16" knurled
shaft pots. Those smaller knurled shafts are typically found in Crate and
Peavey amps. Not recommended for D-shaft type shafts.
Part #PAS-635 |
$0.95 |
|
Click on photo for
larger view |
 KNOB, Revisit™ Quality Reproduction of Marshall™ Knob, Push-on Knurled, Single
Knob.
Excellent quality aftermarket Marshall™ control knobs, push-on type, set of 6
knobs. Designed for the "knurled" type control shafts.
Found on a variety of Marshall™ amps, including some JCM-800, JCM-900,
JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early
ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the
earlier MG series versions as well as other models. Note: In most
cases, the gold color on the new knob will be deeper than the other old knobs on
your amp - the gold caps on Marshall™ knobs fade over time.
Especially true if your amp is ~20 years old or greater (JCM800 and JCM900, for
example).
Since Marshall™ has recently changed the appearance of their original
Marshall™ brand knobs (duller and more of an orange-gold color), we believe
these reproduction knob are now actually closer in appearance to the original
Marshall™ knobs.
Part #MKCPT |
$1.89
(Single Knob) |
|
Click on photo for
larger view |
KNOB
SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 6.
Excellent quality aftermarket Marshall™ control knobs, push-on type, set of 6
knobs. Designed for the "knurled" split-shaft potentiometers.
Found on a variety of Marshall™ amps, including some JCM-800, JCM-900,
JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early
ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the
earlier MG series versions as well as other models. Note: In most cases, the gold
color on the new knob will be deeper than the other old knobs on your amp - the
gold caps on Marshall™ knobs fade over time. Especially true if your
amp is ~20 years old or greater (JCM800 and JCM900, for example).
Part #MKCPT-6 |
$9.95
(Set of 6 knobs) |
|
Click on photo for
larger view |
KNOB
SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 10. Excellent quality
aftermarket Marshall™ control knobs, push-on type,
set of 10 knobs. Designed for the "knurled" split-shaft
potentiometers.
Found on a variety of Marshall™ amps, including some JCM-800, JCM-900,
JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early
ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the
earlier MG series versions as well as other models.
Nothing perks up the tired looks of a road-worthy Marshall™ like a complete new
set of knobs. Older Marshalls typically have knobs where some of the
gold caps have fallen off, and the other gold caps have faded to look more like
silver than gold. It used to be a bit pricey to swap out the
complete set of knobs on some of the JCM900's, but with this
new set of aftermarket Marshall™ knobs, it's affordable. This
set of 10 knobs is perfect for many JCM900 series models with 10 control pots,
such as the 2101, 2501, 4100, 4101, 4102, 4500, 4501, and 4502.
Quality reproduction of the original Marshall™ knobs at half of the
cost.
Part #MKCPT-10 |
$14.95
(Set of 10 knobs) |
|
Click on photo for
larger view |
KNOB
SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 11. Excellent quality
aftermarket Marshall™ control knobs, push-on type,
set of 11 knobs. Designed for the "knurled"
type control shafts (used on some JCM800s - check your
particular amp to make sure it has knurled knobs and not solid smooth shaft pots
with set-screw knobs).
Nothing perks up the tired looks of a road-worthy Marshall™ like a complete new
set of knobs. Older Marshalls typically have knobs where some of the
gold caps have fallen off, and the other gold caps have faded to look more like
silver than gold. It used to be a bit pricey to swap out the
complete set of knobs on some of the split-channel JCM800's with 11 controls, but with this
new set of aftermarket Marshall™ knobs, it's affordable. This
set of 11 knobs is perfect for many split-channel JCM800 series models with 11 control pots,
such as the 2205, 2210, 4210, 4211, 4212, 5210, and 5212. (Check your
particular amp to make sure it has knurled knobs and not solid smooth shaft pots
with set-screw knobs) Quality reproduction of the original Marshall™ knobs at half of the
cost.
Part #MKCPT-11 |
$15.95
(Set of 11 knobs) |
|
Click on photo for
larger view |
KNOB
SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of
25. Excellent quality
aftermarket Marshall™ control knobs, push-on type,
set of 25 knobs. Designed for the "knurled"
type control shafts Nothing perks up the tired looks of a
road-worthy Marshall™ like a complete new set of knobs. Quality reproduction of the original Marshall™ knobs at half of the
cost. This set of 25 knobs is great for repair shops, at less than $1.00
per knob. Found on a variety of Marshall™ amps, including some JCM-800, JCM-900,
JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early
ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the
earlier MG series versions as well as other models.
Part #MKCPT-25 |
$24.95
(Set of 25 knobs) |
|
Click on photo for
larger view |
KNOB
SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of
50. Excellent quality
aftermarket Marshall™ control knobs, push-on type,
set of 50 knobs. Designed for the "knurled"
type control shafts Nothing perks up the tired looks of a
road-worthy Marshall™ like a complete new set of knobs. Quality reproduction of the original Marshall™ knobs at half of the
cost. This set of 50 knobs is great for repair shops, at less than 80
cents
per knob. Found on a variety of Marshall™ amps, including some JCM-800, JCM-900,
JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early
ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the
earlier MG series versions as well as other models.
Part #MKCPT-50 |
$39.95
(Set of 50 knobs) |
|
Click on photo for
larger view |
 KNOB, Marshall™, PUSH ON
D-SHAFT (Read applicable models!)
Standard original Marshall™ control knob, push-on type, for D-Shaft pots used in
the following Marshall™ amp models: DSL-20HR Head, DSL-50 Head, DSL-100 Head, TSL-60
Head, MA-50H Head, MA-100H Head, JVM-205C Combo, JVM-210C Combo, JVM-215C Combo, JVM-410C Combo,
MHZ-15 Haze 15.
Original Marshall™ part. For the similar knob used on some ValveState
models, DSL and TSL combos, MA series combos and JVM series heads, see the R-MKDS-C knob elsewhere
on this page.
The MKDS Knob is constructed so that the pointer on the front of the knob is
directly behind the flat spot in the shaft hole on the back side of the knob.Note: In most
cases, the gold color on the new knob will be deeper than the other old knobs on
your amp - the gold caps on Marshall™ knobs fade over time.
Especially true if your amp is ~20 years old.
Part #MKDS |
$2.99
(Single Knob) |
Currently unavailable from Marshall.
Has been on back-order since October, 2023. |
Click on photo for
larger view |
Save
with Multipack! KNOB, Set of 6 Marshall™, PUSH ON
D-SHAFT (Read applicable models!)
Standard original Marshall™ control knob, push-on type, for D-Shaft pots used in
the following Marshall™ amp models: DSL-20HR Head, DSL-50 Head, DSL-100 Head, TSL-60
Head, MA-50H head, MA-100H Head, JVM-205C Combo, JVM-210C Combo, JVM-215C Combo, JVM-410C Combo,
MHZ-15 Haze 15.
Original Marshall™ part. For the similar knob used on some ValveState
models, DSL and TSL combos, MA series combos and JVM series heads, see the MKDS-C knob elsewhere
on this page. The MKDS Knob is constructed so that the pointer on the front of the knob is
directly behind the flat spot in the shaft hole on the back side of the knob.Note: In most
cases, the gold color on the new knob will be deeper than the other old knobs on
your amp - the gold caps on Marshall™ knobs fade over time.
Especially true if your amp is ~20 years old.
Part #MKDS-6 |
$14.95
(Set of 6 knobs) |
Currently unavailable from Marshall.
Has been on back-order since October, 2023. |
|
 KNOB,
Revisit™ Marshall™, PUSH ON D-SHAFT (Read applicable models!)
Standard Revisit™
Marshall™ style control knob, push-on type, for D-Shaft pots used in
the following Marshall™ amp models: DSL-201 combo, DSL-401 combo,
DSL-40C combo, TSL-122 combo, TSL-601 combo, TSL-602 combo, JVM205H head,
JVM210H head, JVM410H head, VS15 combo, VS30R combo, VS65R combo, VS100R
combo, VS100RH head, VS102R combo, VS230 combo, VS265 combo, AVT20 combo, AVT50
combo, AVT50H head, AVT100 combo, AVT150 combo, AVT150H head, AVT275 combo, AS100D combo, MA50C
Combo, MA100C Combo, MG10, MG15, MG15FX, MG30FX, MG50FX, MG100FX, MG100HFX,
MG102FX.
For the similar knob used on DSL and TSL JCM2000 series heads, MA series heads,
and JVM series combos see the MKDS knob elsewhere on this page.
The R-MKDS-C Knob is constructed so that the pointer on the front of the knob is
180 degrees away from the flat spot in the shaft hole on the back side of the
knob.
Part #R-MKDS-C |
$2.99
(Single Knob) |
|
Click on photo for
larger view |
KNOB,
Revisit™ Quality REPRODUCTION of Marshall™, Set Screw.
Revisit™ aftermarket Marshall™ control knob, with
gold cap and set screw.
Fits 1/4" shaft. Similar to original Marshall™ set-screw knob. This style of knob was used mainly in
the 60s and 70s. Note: 1960s Plexi models may have a smaller knob.
Those are no longer available, so we recommend these as a replacement.
Comments on appearance and construction: In most cases, the gold color on the
new knob will be deeper than the other old knobs on your amp - the gold caps on
Marshall™ knobs fade over time. Since Marshall has recently changed the appearance of their original Marshall brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall knobs.
These knobs have a brass insert, so they tend to be
more durable than the genuine all-plastic Marshall knobs.
Part #MKSS |
$1.99
(Single Knob) |
|
Click on photo for
larger view |
KNOB
SET, Marshall™ type, Set Screw, Set of 6.
Revisit™ aftermarket Marshall™ control
knobs, with
gold cap and set screw.
Fits 1/4" shaft, set of 6 knobs. Similar to original Marshall™ set-screw knob. This style of knob was used mainly in
the 60s and 70s. Note: 1960s Plexi models may have a smaller
knob. Those are no longer available, so we recommend these as a
replacement.
Comments on appearance and construction: In most cases, the gold color on the
new knob will be deeper than the other old knobs on your amp - the gold caps on
Marshall™ knobs fade over time. Since Marshall has recently changed the appearance of their original Marshall brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall knobs.
These knobs have a brass insert, so they tend to be
more durable than the genuine all-plastic Marshall knobs.
Part #MKSS-6 |
$9.95
(Set of 6 knobs) |
|
SET SCREW
Click on photo for
larger view |
KNOB,
Revisit™ Quality REPRODUCTION of Marshall™, Black Top, Set Screw.
Revisit™ aftermarket Marshall™ control knob, with
black metal cap, brass insert and set screw. Fits 1/4"
shaft. Similar to original Marshall™ set-screw knob used on the early
Marshall models until the early 1980s. Shiny ridged
black metal top on black plastic body.
Part #MKBSS |
$1.99
(Single Knob) |
|
PUSH-ON
Click on photo for
larger view |
KNOB,
Revisit™ Quality REPRODUCTION of Marshall™, Black Top, Push-On.
Revisit™ aftermarket Marshall™ control knob, with
black metal cap, push-on for knurled shaft pots, used on most Marshall
models from the late 1980s to the present. Similar to original
Marshall™ push-on knobs. Shiny ridged black metal top on black
plastic body.
Part #MKBPT |
$1.99
(Single Knob) |
|
Click on photo for
larger view |
KNOB, Silver Marshall™ type, SET SCREW
Revisit™ aftermarket Marshall™ control knob, with
silver cap and set screw.
Fits 1/4" smooth shaft. Similar to original silver Marshall™ set-screw knob,
which has been discontinued.
Part #MKSSS |
$1.99
(Single Knob) |
|
Click on photo for
larger view |
KNOB, Silver Marshall™ type, PUSH ON
Revisit™ aftermarket Marshall™ control knob, with
silver cap and designed to fit a "knurled" 1/4" shaft. No
set-screw. Similar to original silver Marshall™ knob,
which has been discontinued.
Part #MKSPT |
$1.99
(Single Knob) |
|
Click on photo for
larger view |
MARSHALL
POWER SWITCH BUTTON FOR VALVESTATE SERIES II AMPS
Power switch button for the second ValveState series,
including models VS15, VS30R, VS65R, VS100R, VS100RH, VS102R, VS230, VS232 AND
VS265. Also for the Bass State 150. Marshall reference numbers SW1008KNOPF. Fits the
SW-160 power switch.
Part #K-108 |
$2.50 |
|
Click on photo for
larger view |
ROUND SWITCH CAP - FITS SW-212 and 090-0012-0
This is a black 5mm (approx 3/16") diameter X 9mm long switch cap which fits the SW-212
and 090-0012-0 Push Switches. Exact replacement for most of the
round caps used on the Gallien-Krueger 400RB-II, 700RB-II, 1001RB and similar models. The diameter of this switch cap
is smaller than the original round switch cap from Marshall™ found on some of
the early ValveState models. Does NOT fit the TSL/DSL amps in the JCM2000
series. For switches with actuator shaft of 2.7mm square.
Part #K-212 |
$1.50 |
|
Click on photo for
larger view |
SQUARE SWITCH CAP - FITS SW-212
This is a black 5mm x 5mm (approx 3/16") square mini-switch cap which fits the SW-212
Marshall™ Push Switch (used primarily for channel switching). Replaces the original S213 switch cap from Marshall™ ,
which has now been discontinued. NOTE: This is
NOT the power switch cap on ValveState Amps. Also, this switch cap
does NOT fit the SW-650 switch. This square cap is found on
the Marshall™, 6100, 6101, JMP1, JCM600, JCM602, JTM310, JTM312, JTM610, JTM612,
JTM615, JTM622, 8010, AS80R, 8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280, and
9004 models. For switches with actuator shaft of 2.7mm square.
Part #K-213 |
$1.50 |
|
Click on photo for
larger view |
 KNOB, Music Man™, SET-SCREW
Music Man™ style amp knob, skirted with 1-10 numbering. Traditional
"Witches Hat" design. For vintage Music Man™ amps. With set-screw,
for 1/4" smooth shaft pots.
These are different than the Fender skirted knobs. A lot of people
put Fender knobs on Music Man amps, but they won't exactly match the other
knobs. This is the exact replacement.
Part #K-155 |
$5.50 |
|
Click on photo for
larger view |
KNOB, Fender™ STYLE, SET-SCREW
Fender™ style amp knob, skirted with 1-10 numbering. Traditional
"Witches Hat" design. For vintage Fender™ amps in the original blackface and silverface series,
as well as the blackface and silverface reissue series. With set-screw,
for 1/4" smooth shaft pots.
Replaces Fender™ part number 0990930000.
Part #FVSK |
$5.50 |
|
Click on photo for
larger view |
 KNOB, Fender™, 1-10, Acoustasonic series,
Brown.
Genuine Fender™ amp knob, skirted with 1-10 numbering.
Brown in color, center is indented chrome. For the Acoustasonic series of amplifiers.
Used on Acoustasonic amps manufactured from 2005-2011. Knob is a slip-on, designed to fit a "D-shaped" shaft. Original Fender™ part number
0055758049.
Part #K-758 |
$8.50 |
 |
Click on photo for
larger view |
KNOB, Fender™, 1-10, Acoustasonic series,
Brown.
Genuine Fender™ amp knob, skirted with 1-10 numbering.
Brown in color. For the Acoustasonic series of amplifiers.
Used on Acoustasonic amps manufactured from 1998-2004. Knob is a slip-on, designed to fit a "D-shaped" shaft. Original Fender™ part number
00551018000.
Part #K-329 |
$8.50 |
|
Click on photo for
larger view |
KNOB, Fender™, 1-10, Princeton 65 and Princeton
65 DSP
Genuine Fender™ amp
knob, black, chrome center disc, skirted with 1-10 numbering. Knob is a
slip-on, designed to fit a "D-shaped" shaft
(with flat portion of "D" shaft facing
the 1 o'clock
position when potentiometer is turned down to minimal level). 7/8"
diameter. For the
Princeton 65/65 DSP/650, Champion 30/30
DSP, Super Champ™ X2, Super Champ™ XD, Cyber-Champ™,
Super Bassman™
(2012) amplifiers. Also used as the line-out
level control knob on the Acoustasonic™ Jr DSP. Original Fender™ part number
0054419000.
Part #K-328 |
$3.95 |
|
Click on photo for
larger view |
KNOB, Fender™ style "mini witch's hat", skirted
1-10
Fender™ style amp knob, black, chrome center disc, skirted, with 1-10 numbering. Knob is a
slip-on, designed to fit a knurled shaft pot. Base
is 7/8"
diameter. Fits
any split knurled shaft pot, such as those found on certain models of the
Sidekick series, the Rumble series etc. Same as K-328, but for
knurled shaft pots instead of D-shaft. Also will fit other
amp brands with knurled shaft pots.
Part #K-338 |
$1.95 |
|
Click on photo for
larger view |
BUSHING, Fender™, for push-on knobs such as the K-2049 and K-3049 and others.
This bushing slides over the pot shaft before the knob is installed, and stabilizes the shaft as well as keeping the knob from rubbing the front faceplate. The tapered end of the bushing fits into the hole in the faceplate. The knob is inserted after the bushing is in place, and hides the bushing from view. Original Fender™ part number 0033206049.
Part #K-6049 |
$1.00 |
|
Click on photo for
larger view |
BUTTON,
for push switch, Black.
This black button pushes onto the
switch stem. Used on channel control and drive boost switches on the
front panel of the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, Blues
Deville, Blues Junior. Original Fender™ part number 0028104000.
Button only - not the complete switch. For the switch, see SW-028.
Fits switches with
actuator shaft of 2.7mm square.
Part #K-058 |
$2.95 |
|
Click on photo for
larger view |
BUTTON,
for push switch, White.
This white button pushes onto the
switch stem. Used on channel control and drive boost switches on the
front panel of the Fender™ Hot Rod Deluxe III, Hot Rod Deville III, and on the
FAT switch of the Blues Junior III and Blues Junior IV. Used on the
channel selection switch of the Super champ X2 and Super Champ XD. Original Fender™ part number 0048451000.
Button only - not the complete switch. For the switch, see SW-028.
Fits switches with
actuator shaft of 2.7mm square.
Part #K-048 |
$2.95 |
|
Click on photo for
larger view |
 BUTTON,
for push switch, Red.
This red button pushes onto the
switch stem. Used on the front panel buttons of the Eden TN501 Bass
Amp.
Button only - not the complete switch.
Fits switches with
actuator shaft of 2.7mm square.
Part #K-068 |
$2.95 |
|
Click on photo for
larger view |
KNOB, Fender™, Red with Pointer
The infamous Fender Red Knob.
Genuine Fender™ amp knob, red with white pointer. Knob is a slip-on, designed to fit a "D-shaped" shaft. Original Fender™ part number 0990931000
and 025952.
Will NOT fit certain models of amps, including the M-80 heads and rack-mount
models and the BXR-300R and BXR-300C.
Part #K-320 |
Discontinued by Fender. No longer available. |
|
Click on photo for
larger view |
KNOB, Fender™, Black with Pointer
Genuine Fender™ amp knob, black with white pointer. Knob is a slip-on, designed to fit a "D-shaped" shaft. Original Fender™ part number 0990932000.
Will NOT fit certain models of amps, including the M-80 series and BXR series.
Will not fit combo amps which have pots with black plastic shafts, such as the
Princeton 112 and Princeton 112 Plus.
Part #K-321 |
Discontinued by Fender. No longer available. |
|
Click on photo for
larger view |
 KNOB KIT, Fender™
Style, Black with Pointer with
bushing.
Replacement for
Fender™ Blues Junior III. Upgrade knob for original Blues Junior,
Bronco, and Pro Junior. Includes the Fender™ style 36620000 Black
Chicken-Head knob and the 0033206049
bushing. Knob is a 1/4" set-screw type. This combination replaces
the original 041710 push-on knob used on the original Blues Junior, Bronco and
Pro Junior - the 041710 knob is now discontinued.
Part #K-710 |
$2.95 |
|
Click on photo for
larger view |
KNOB, Fender™ Style, Vintage Cream
Replaces
Fender™ part number 0990933000.
"Fender™ Barrel" knob, cream white with brass inset and set-screw as used by:
Fender™ 1960-1964 for the Fender™ Bassman, Showman and Bandmaster Amp, and for
several Fender™ Custom Shop and Fender™ Reissue amps:
Tone Master, Custom Vibrolux Reverb, Vibroking, Super Sonic Amp (blonde) etc.
Part #K-315 |
$2.95 |
|
Click on photo for
larger view |
KNOB, Fender™ Style, Vintage Cream,
Set of 6
Replaces
Fender™ part number 0990933000.
"Fender™ Barrel" knob, cream white with brass inset and set-screw as used by:
Fender™ 1960-1964 for the Fender™ Bassman, Showman and Bandmaster Amp, and for
several Fender™ Custom Shop and Fender™ Reissue amps:
Tone Master, Custom Vibrolux Reverb, Vibroking, Super Sonic Amp (blonde) etc.
Set of 6 knobs.
Part #K-315-6 |
$16.95
(for pack of 6 knobs) |
|
Click on photo for
larger view |
KNOB, Fender™ Style, Vintage Brown
Fender™ style amp knob,
brown color with white pointer. Used on Fender™ "Brownface" series
amps from 1961 through 1963. Knob is secured by set-screw,
designed to fit a 1/4" shaft. Includes internal brass inset.
Replaces Fender™ part number 0990934000,
these knobs were used by
Fender™ in the early 1960s for the Brown-Tolex Amps (Princeton 6G2, Deluxe 6G3,
Super 6G4, Pro 6G5, Tremolux 6G9, Vibrolux 6G11, Concert 6G12, Reverb Unit 6G15,
Vibroverb 6G16), and others . Also very similar to the
knob used on the Mesa-Boogie Maverick Dual
Rectifier model - Mesa Boogie part number 408020.
Part #K-316 |
$2.95 |
|
Click on photo for
larger view |
KNOB, Fender™ Style, Vintage Brown,
Set of 6
Fender™ style amp knob,
brown color with white pointer. Used on Fender™ "Brownface" series
amps from 1961 through 1963. Knob is secured by set-screw,
designed to fit a 1/4" shaft. Includes internal brass inset.
Replaces Fender™ part number 0990934000,
these knobs were used by
Fender™ in the early 1960s for the Brown-Tolex Amps (Princeton 6G2, Deluxe 6G3,
Super 6G4, Pro 6G5, Tremolux 6G9, Vibrolux 6G11, Concert 6G12, Reverb Unit 6G15,
Vibroverb 6G16), and others . Also very similar to the
knob used on the Mesa-Boogie Maverick Dual
Rectifier model - Mesa Boogie part number 408020.
Set of 6 knobs.
Part #K-316-6 |
$16.95
(for pack of 6 knobs) |
|
Click on photo for
larger view |
KNOB, Fender™ Style, Vintage Black
Fender™ style amp knob,
black color with white pointer. Includes internal brass inset. Knob is secured by set-screw, designed to fit a 1/4" shaft.
Can be used for Fender™ Brown-Tolex Amps (Princeton 6G2, Deluxe 6G3, Super 6G4,
Pro 6G5, Tremolux 6G9, Vibrolux 6G11, Concert 6G12, Reverb Unit 6G15, Vibroverb
6G16)
Part #K-325 |
$2.95 |
|
Click on photo for
larger view |
KNOB, Peavey™, modified Chicken Head style
Genuine Peavey™ amp
knob, black with thin white pointer. This is a full-size knob, about 1-1/4 inch
long. For 3/16" diameter knurled shaft. Note:
This knob will NOT fit the 6505+ 112 Combo amp. Original Peavey part
number 70902145 or 30902145.
Part #K-428 |
$5.99 |
|
Click on photo for
larger view |
KNOB, Electro-Harmonix™, Black with Cross Slot and White Dot Indicator
1/4" Shaft, with set screw. General control knob, fits all
current EH pedals, plus a variety of other applications. 0.80"
wide at the base, 0.62" wide at the top, 0.61" tall.
Part #K-344 |
$1.99 |
|
Click on photo for
larger view |
KNOB, Medium, Black with White Line Indicator,
for
1/4" smooth shaft, with set screw. Great effects pedal knob. 0.75"
diameter, 0.575" tall (19mm x 15mm). Clone of the Davies 1510
knob.
Part #K-202 |
$1.49 |
|
Click on photo for
larger view |
KNOB, Medium, Cream/Beige with Black Line Indicator. Push-on,
for knurled shaft pots (no set screw) Great effects pedal knob for
knurled shaft ports.
0.75" diameter, 0.575" tall (19mm x 15mm) Used in many Egnater™ amp models
including the Rebel, Renegade, and Tourmaster series as well as others.
Designed for push-on knurled pot shafts (no set screw). Not for the Egnater™ Mk II series.
Part #K-151 |
$1.79 |
|
Click on photo for
larger view |
REPRODUCTION OF the DAVIES 1900H KNOB, BLACK KNOB WITH WHITE LINE
Reproduction of the small
1900H Davies knob.
Looks great on pedals. 1/4" Shaft, Size-Diameter 12.7mm, height 15.9mm,
With Set Screw.
Part #K-559 |
$1.99 |
|
Click on photo for
larger view |
KNOB, Electro-Harmonix™, Large Black with White Line Indicator Push
on for 1/4" Knurled Shaft. Used on many
current EH pedals, plus a variety of other applications. 1.00"
wide, 0.62" tall.
Part #K-346 |
$1.99 |
|
Click on photo for
larger view |
KNOB, Electro-Harmonix™, Small Black with White Line Indicator Push
on for 1/4" Knurled Shaft. Used on many
current EH pedals, plus a variety of other applications. 0.66"
wide, 0.53" tall.
Part #K-347 |
$1.99 |
|
 |
KNOB, Black Plastic with Colored Pointer. Push
on type for 1/4" Knurled Shaft. Excellent replacement for knobs
on mixers or pedals which have knurled split 1/4" shaft pots. Soft touch,
high quality. Height: 17mm, Bottom Diameter: 16mm, Top
Diameter: 12mm. Available with different pointer colors:
Blue, Gray, Green, Orange, Red, White or Yellow. Choose pointer color in
"Options", above the Add to Cart button
Part #K-350 |
$1.00 |
|
 |
KNOB, Soft Rubber, Black Body with Colored Pointer. Push
on type for 1/4" Knurled Shaft. Excellent replacement for knobs
on mixers or pedals which have knurled split 1/4" shaft pots. Soft touch
rubber,
high quality. Height: 14mm, Bottom Diameter: 16mm, Top
Diameter: 11mm. Available with Red, White, or Blue pointer. Choose pointer color in
"Options", above the Add to Cart button.
Part #K-817 |
$1.00 |
|
Click on photo for
larger view |
KNOB, Ampeg™, SVT Classic
Genuine Ampeg™ amp knob,
black with white pointer. Fits pots with 1/4" D-shaft type shafts (SVT
Classic). Ampeg part number 45-231-51.
Part #K-324 |
$5.95 |
|
Click on photo for
larger view |
KNOB, BLACK KNOB WITH WHITE LINE, SILVER TOP, SET SCREW WITH BRASS INSERT.
CLASSIC LOOK FOUND ON BOSS EFFECTS PEDALS
Small size 0.78"
(20mm) diameter, 0.43" (11mm) tall, fits
smooth 1/4" shaft. Classic look found on Boss FX units.
With set screw.
Part #K-828 |
$1.79 |
|
Click on photo for
larger view |
KNOB, BLACK KNOB WITH WHITE LINE, SILVER TOP, SET SCREW WITH BRASS INSERT.
CLASSIC LOOK FOUND ON BOSS EFFECTS PEDALS
Medium size 0.91"
(23mm) diameter, 0.5" (12mm) tall, fits
smooth 1/4" shaft. Smooth silver top. Classic look found on
Boss FX units.
With set screw.
Part #K-348 |
$1.95 |
|
Click on photo for
larger view |
KNOB, BLACK KNOB WITH WHITE LINE, SILVER TOP, SET SCREW WITH BRASS INSERT.
CLASSIC LOOK FOUND ON BOSS EFFECTS PEDALS
Large size 1.06" (27mm) diameter, 0.6"
(15mm) tall, fits
smooth 1/4" shaft. Smooth silver top. Classic look found on
Boss FX units. With set
screw.
Part #K-372 |
$1.95 |
|
Click on photo for
larger view |
 DUNLOP MXR KNOB, BLACK KNOB WITH WHITE LINE
Original Dunlop MXR Knob - as used on the Phase 90 and other MXR pedals.
Part #D-ECB130 |
$3.99 |
|
Click on photo for
larger view |
REPRODUCTION OF the DUNLOP MXR KNOB, BLACK KNOB WITH WHITE LINE
Good replica of the
Dunlop MXR™
Knob - as used on the Phase 90 and other MXR™
pedals.
Also a good replacement for knobs on most Orange™
Amps. 1"
(25.4mm) diameter at the base x 0.6" (15mm) high.
Set Screw, for smooth shaft pots.
Part #K-345 |
$1.99 |
|
Click on photo for
larger view |
REPRODUCTION OF THE MINI MXR™ KNOB, BLACK KNOB WITH WHITE LINE
Reproduction of the small
MXR™ Knob. Diameter (bottom):
20mm at the base. Height: 11.45mm With Set Screw for smooth 1/4" shafts.
Datasheet
Part #K-830 |
$1.99 |
|
Click on photo for
larger view |
DUNLOP MXR KNOB COVER
Original Dunlop MXR Knob Cover - as used on the Phase 90 and other MXR pedals.
Part #D-ECB131 |
$2.79 |
|
Click on photo for
larger view |
REPRODUCTION OF the DAVIES 1900H KNOB, BLACK KNOB WITH WHITE LINE,
SET SCREW
Reproduction of the small
1900H Davies knob.
Looks great on pedals. 1/4" Shaft, Size-Diameter 12.7mm, height 15.9mm,
with Set Screw for smooth shaft pots.
Part #K-559 |
$1.99 |
|
Click on photo for
larger view |
KNOB, BLACK KNOB WITH WHITE LINE, SET SCREW WITH BRASS INSERT.
Large 1.06" diameter, 0.6" tall, fits
smooth 1/4" shaft. Classic look found on vintage guitar and bass amps.
Part #K-349 |
$1.95 |
|
Click on photo for
larger view |
DAVIES STYLE 1400 REPRODUCTION KNOB.
Replaces the Dunlop ECB245 knob. Small knob, 11/16" diameter x
13/32" high. For 1/4" smooth shaft - with set screw.
Part #K-1400 |
$1.99 |
|
Click on photo for
larger view |
DAVIES STYLE 1470 REPRODUCTION KNOB.
Used on a number of classic effects pedals.
Larger knob, 1" diameter (at the base) x 1/2" high.
Pointer extends about 3mm beyond the outside rim of the knob. Black
thermoset plastic, for 1/4" smooth shaft - with
brass set screw.
Part #K-1470 |
$2.49 |
|
Click on photo for
larger view |
MULTI-PACK, KNOB, CHICKEN HEAD, SET SCREW, BLACK,
SET OF 6 - SAVE!
Used in Fender™ and many other retro style amps. Black. Fits 1/4" shaft, brass insert, with set screw.
Set of 6 knobs. Standard chicken-head knob size, 31.5mm nose to tail,
13.5mm tall.
Part #CHKBK-6 |
$7.49 |
|
Click on photo for
larger view |
KNOB, CHICKEN HEAD, SET SCREW, BLACK
Used in Fender™ and many other retro style amps. Black. Fits 1/4" shaft, brass insert, with set screw.
Standard chicken-head
knob size, 31.5mm nose to tail, 13.5mm tall.
Part #CHKBK |
$1.95 |
|
Click on photo for
larger view |
KNOB, CHICKEN HEAD, KNURLED PUSH-ON, BLACK
Used on many retro style amps - can replace any knob which uses a 1/4" knurled type shaft. Black. Fits 1/4" knurled shaft only.
Standard chicken-head knob size, 31.5mm nose to tail, 13.5mm tall.
Part #CHKBK-K |
$1.95 |
|
Click on photo for
larger view |
 KNOB, CHICKEN HEAD,
VOX KNURLED PUSH-ON, BLACK
Used on many Vox amps - can replace any knob which uses a 1/4" knurled type shaft. Black. Fits 1/4" knurled shaft only.
Standard chicken-head knob size, 31.5mm nose to tail, 13.5mm tall.
Part #K-V11 |
$1.95 |
|
Click on photo for
larger view |
KNOB, CHICKEN HEAD, SET SCREW, WHITE
Used in Fender™ and many other retro style amps. White. Fits 1/4" shaft, brass insert, with set screw.
Standard chicken-head knob size, 31.5mm nose to tail, 13.5mm tall.
Part #CHKWH |
$1.95 |
|
|
Click on photo for
larger view
|
KNOB, CHICKEN HEAD, SET SCREW, BLUE
Used in Fender™ and many other retro style amps. Blue. Fits 1/4" shaft, brass insert, with set screw.
Standard chicken-head knob size, 31.5mm nose to tail, 13.5mm tall.
Part #CHKBL |
$1.95 |
|
|
Click on photo for
larger view
|
KNOB, CHICKEN HEAD, KNURLED PUSH-ON, BLUE
Used on many retro style amps - can replace any knob which uses a 1/4" knurled type shaft. Blue. Fits 1/4" knurled shaft only.
Standard chicken-head knob size, 31.5mm nose to tail, 13.5mm tall.
Part #CHKBL-K |
$1.95 |
|
Click on photo for
larger view |
KNOB, CHICKEN HEAD, SET SCREW, CREAM
Used in Fender™ and many other retro style amps. Cream. Fits 1/4" shaft, brass insert, with set screw.
Standard chicken-head knob size, 31.5mm nose to tail, 13.5mm tall.
Part #CHKCR |
$1.95 |
|
Click on photo for
larger view |
KNOB, CHICKEN HEAD, SET SCREW, RED
Used in Fender™ and many other retro style amps. Red. Fits 1/4" shaft, brass insert, with set screw.
Standard chicken-head knob size, 31.5mm nose to tail, 13.5mm tall.
Part #CHKRD |
$1.95 |
|
Click on photo for
larger view |
KNOB, CHICKEN HEAD, KNURLED PUSH-ON, RED
Used on many retro style amps - can replace any knob which uses a 1/4" knurled type shaft. Red. Fits 1/4" knurled shaft only.
Standard chicken-head knob size, 31.5mm nose to tail, 13.5mm tall.
Part #CHKRD-K |
$1.95 |
|
Click on photo for
larger view |
KNOB, CHICKEN HEAD, SET SCREW, BROWN
Used in Fender™ and many other retro style amps. Red. Fits 1/4" shaft, brass insert, with set screw.
Standard chicken-head knob size, 31.5mm nose to tail, 13.5mm tall.
Part #CHKBN |
$1.95 |
|
Click on photo for
larger view |
KNOB, MINI CHICKEN HEAD, SET SCREW, CREAM
Mini Chicken Head Knob for smaller
applications such as effects pedals. Cream. Fits 1/4"
smooth shaft, brass insert, with set screw. 0.90 inches from nose to tail.
Regular chicken head knobs are 1.2 inches long. Clone of the Davies
2300 knob.
Part #MCHKCR |
$1.49 |
|
Click on photo for
larger view |
KNOB, MINI CHICKEN HEAD, SET SCREW, BLACK
Mini Chicken Head Knob for smaller
applications such as effects pedals. Black. Fits 1/4"
smooth shaft, brass insert, with set screw. 0.90 inches from nose to tail.
Regular chicken head knobs are 1.2 inches long. Clone of the Davies
2300 knob.
Part #MCHKBK |
$1.49 |
|
Click on photo for
larger view |
L-PAD FACE PLATE AND KNOB, for 3/8" diameter threaded bushing found on most L-Pad Level
controls. Face plate AND knob only! L-Pad ordered separately.
Fits many bass
cabinets including the SWR Goliath, Marcus Miller Golight 410, Workingman
8x10, Working Pro 2x10, Ampeg PN-210HLF, PN-410HLF, SVT-410HLF, SVT-610HLF,
SVT-810SPC, BXT210M,
BXT410HL4, PR-1528HE, PN-115HLF, PR-810H, PB-250, the Kustom G410H, the
Engl B115 as well as many others.
This is the face plate and knob only - L-PAD itself ordered separately.
Raised lettering in charcoal gray instead of white. 3 1/8 inches in
diameter, 7/8 inch depth into cabinet. Requires 2 inch diameter hole
for mounting. Screws not included.
Part #LFP-380 |
$4.50 |
|
Copyright ©2024 Studio Sound Electronics - All Rights Reserved
Not responsible for web site errors or omissions.
WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov
|
