JCM900 Series
Parts JCM900 Series amps include the
following model numbers: 2100, 2101, 2500, 2501, 2502, 4100, 4101,
4102, 4500, 4501, 4502, 2100SL-X, 2101SL-X, 2500SL-X, 2501SL-X, 2502SL-X
NOTE: MARSHALL APPEARS TO BE IN
SERIOUS TROUBLE, AND IS NOT SHIPPING NEW ORDERS OF
PARTS TO THE UNITED STATES AT THIS TIME.
THEY WERE BOUGHT BY ZOUNDS, INC. OF SWEDEN
ABOUT A YEAR AGO, WHO HAS NOW REBRANDED
THEMSELVES AS "MARSHALL GROUP".
ONCE WE RUN OUT OF A PARTICULAR ITEM, WE
ARE CURRENTLY UNABLE TO RESTOCK IT.
We carry an extensive selection of Marshall™
Amplifier parts for both vintage and modern amps.
JACK, 1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE 4 PC board terminals, switched. Used in many modern Marshall™TM
amp models, including the JCM900 series, the Valvestate Series 1 models, JCM2000
series, and several others. Also used in many other brands of British amps.
With nut and washer. Marshall part number J3B6005A or S122.
Part #J-503
$1.99
Click on photo for
larger view
WASHER, FOR BRITISH STYLE (CLIFF) JACKS. This washer goes behind the faceplate on British style plastic nut and
chrome nut jacks to provide proper spacing. Jacks come with the
washers included, but the washers are easily lost. Without the washers,
the jacks will not fit properly. Part #W-583
$0.18
for each washer.
(Jacks not included).
Click on photo for
larger view
JACK,
1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE WITH CHROME NUT AND CHROME TRIM RING
4 PC board terminals, switched. Used in many brands of amps and other
equipment. Same footprint as J-503 jack - may be used in place of
J-503 to add a touch of "chrome" class to your amp! Part #J-603
$2.79
(per jack)
Click on photo for
larger view
SAVE WITH MULTIPACK! JACK, 1/4", MONO PC MOUNT PLASTIC,
BRITISH STYLE,
PACK OF 6 4 PC board terminals, switched. Used in many modern Marshall™TM
amp models, including the JCM900 series, the Valvestate Series 1 models, JCM2000
series, and several others. Also used in many other brands of British amps.
Marshall part number J3B6005A or S122. Pack of 6 jacks, with nuts and washers. Part #J-503-6
$9.99
(Set of 6 jacks)
Click on photo for
larger view
JACK, 1/4", MONO PC MOUNT
PLASTIC, BRITISH STYLE, RED NUT, REPLACEMENT FOR Marshall™ SPEAKER JACKS. 4 PC board terminals, switched. Used in
modern Marshall™TM
amp heads (JCM2000 series TSL and DSL, for example) as the output jack for the
speaker cabinet. With red nut and washer. Part #J-503R
$2.39
Click on photo for
larger view
JACK, 1/4", STEREO INPUT, CLOSED CIRCUIT, PC MOUNT, BRITISH STYLE Stereo jack. 6 PC board terminals, switched. With nut and washer.
British style. Part #J-504
$2.15
Click on photo for
larger view
JACK,
1/4", STEREO PC MOUNT PLASTIC, BRITISH STYLE WITH CHROME NUT AND CHROME TRIM RING 6 PC board terminals, switched. Used in many brands of amps and other
equipment. Same footprint as J-504 jack - may be used in place of
J-504 to add a touch of "chrome" class to your amp! Part #J-604
$2.99
(per jack)
Click on photo for
larger view
SAVE WITH MULTIPACK! JACK, 1/4", STEREO, CLOSED CIRCUIT, PC MOUNT,
BRITISH STYLE,
PACK OF 6
Stereo jack. 6 PC board terminals, switched. Pack of 6 jacks, with
nuts and washers. Part #J-504-6
$10.99
(Set of 6 jacks)
Click on photo for
larger view
SAVE WITH
OUR
MULTIPACK ASSORTMENT! THIS PACK CONTAINS THREE J-503 (4 PIN) AND THREE J-504 (6-PIN)
JACKS. Many amps contain both the 4 pin and the 6 pin British jacks. This
assortment gives you 3 of each jack ... Three J-503, and three J-504.
Part # J-5034-6
$10.49
(For 3 J-503 Jacks and 3 J-504 Jacks)
Click on photo for
larger view
JACK NUT, PLASTIC,
BRITISH STYLE, REPLACEMENT FOR Marshall™ AND OTHERS.
Replacement jack nut as found on the J-503, J-504 jacks. Part #J-5NT
$0.50
Click on photo for
larger view
JACK NUT MULTI-PACK - SAVE!
6 JACK NUTS, PLASTIC, BRITISH STYLE, REPLACEMENT FOR Marshall™ AND OTHERS.
Replacement jack nut as found on the J-503, J-504 jacks Part #J-5NT-6
$2.39
Click on photo for
larger view
JACK NUT, PLASTIC,
BRITISH STYLE, RED
Replacement nut for the J-503, J-504.
Red nuts on these jacks typically are used on later model Marshall™ amps to
designate the 'speaker' jacks. Part #J-5NTR
$0.89
Click on photo for
larger view
Complete Marshall™ Potentiometer Kit, 8 SINGLE GANG POTS
AND 1 DUAL GANG POT.
ORIGINAL Marshall™ REPLACEMENT PARTS. Complete replacement Potentiometer Kit for the Marshall™
JCM900 amp models 2100, 2101, 2500, 2501 and 2502 with 8 pots on the front panel and 1
effects level pot on the rear panel. NOT for the JMP combo model 2100 from the 1970s.
NOT for the 2100SL-X, 2101SL-X, 2500SL-X, 2501SL-X or 2502SL-X - see the
MPK-9 Potentiometer Kit for those SL-X models Part #MPK-1
$24.95
Click on photo for
larger view
Complete Marshall™ Potentiometer Kit, 10 SINGLE GANG POTS
AND 1 DUAL GANG POT.
ORIGINAL Marshall™ REPLACEMENT PARTS. Complete replacement Potentiometer Kit for the Marshall™
JCM900 amp models 4100, 4101, 4102, 4500, 4501 and 4502 Dual Reverb with 10 pots on the front panel and 1
effects level pot on the rear panel. Part #MPK-2
$29.95
Click on photo for
larger view
Complete Marshall™ Potentiometer Kit, 8 SINGLE GANG POTS
AND 1 DUAL GANG POT.
ORIGINAL Marshall™ REPLACEMENT PARTS. Complete replacement Potentiometer Kit for the Marshall™
JCM900 SL-X amp series, including the models 2100SL-X, 2101SL-X, 2500SL-X, 2501SL-X and 2502SL-X with 8 pots on the front panel and 1
effects level pot on the rear panel. Part #MPK-9
$24.95
Click on photo for
larger view
Complete Marshall™ Potentiometer Kit,
17 SINGLE GANG POTS.
ORIGINAL Marshall™ REPLACEMENT PARTS. MARSHALL 30th ANNIVERSARY
6100/6101. Complete replacement Potentiometer Kit for the Marshall™
30th Anniversary 6100 head and 6101 combo amplifiers with 17 pots on the front panel. Part #MPK-10
$45.95
Click on photo for
larger view
POT, PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING.
ORIGINAL Marshall™ REPLACEMENT PART. Used in Marshall™ Valvestate I, JCM900, JCM600,
JTM30, JTM60, and 6100 Series. Used in Marshall™ models: AS80R, 8040, 8080, 8100, 8200, 8240, 8280,
JCM900 Models: 2100, 2101, 2500, 2501, 4100, 4500, 4101, 4102, 4501, 4502, SL-X
2100, SL-X 2500, 6100, 6101, JTM60 and JTM30 Series.
Also
used in other amps besides Marshall™.
Available values: B4.7K, B10K, B22K, B50K, A100K, B100K, B220K, and
A1M. Select Pot Value in Options INCLUDES NUT & WASHER
(For spare or replacement nut,
order the PNW-16 nut and washer set found here). Part #P-VM16-XX
$2.95
Click on photo for
larger view
POT, 10K OHM X2 LINEAR DUAL, (B10K), PC MOUNT, 6 MOUNTING PINS, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING.
ORIGINAL Marshall™ REPLACEMENT PART. Used in Marshall™ Valvestate I, JCM900 and JCM600 Series. Also used in the
JMP1 Preamp as Output Level Control. Used in Marshall™ models: AS80R, 8040, 8080, 8100, 8200, 8240, 8280, JCM900 Models:
2100, 2101, 2500, 2501, 2502, 4100, 4500, 4101, 4102, 4501, 4502, SL-X 2100,
SL-X 2500, 6100, 6101, JTM60 and JTM30 Series. Diameter of the body of the pot is slightly smaller than a dime.
Shaft length is 11.5mm. Fits many other amps besides Marshall™. INCLUDES NUT & WASHER
(For spare or replacement nut,
order the PNW-16 nut and washer set found here). Part #P-V10KLX2-M16
$6.95
Click on photo for
larger view
KNOB, Revisit™ Quality Reproduction of Marshall™ Knob, Push-on Knurled, Single
Knob.
Excellent quality aftermarket Marshall™ control knobs, push-on type.
Designed for the "knurled" type control shafts.
Black with gold top. Used on the
JCM-900 series amplifiers.
Since Marshall™ has recently changed the appearance of their original
Marshall™ brand knobs (duller and more of an orange-gold color), we believe
these reproduction knob are now actually closer in appearance to the original
Marshall™ knobs. Part #MKCPT
$1.89
(Single Knob)
Click on photo for
larger view
KNOB
SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 6.
Excellent quality aftermarket Marshall™ control knobs, push-on type, set of 10
knobs. Designed for the "knurled" split-shaft potentiometers.
Found on a variety of Marshall™ amps, including some JCM-800, JCM-900,
JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early
ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the
earlier MG series versions as well as other models. Since
Marshall™ has recently changed the appearance of their original Marshal™l brand
knobs (duller and more of an orange-gold color), we believe these reproduction
knobs are now actually closer in appearance to the original Marshall™ knobs. Part #MKCPT-6
$9.95
(Set of 6 knobs)
Click on photo for
larger view
KNOB
SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of 10. Excellent quality
aftermarket Marshall™ control knobs, push-on type,
set of 10 knobs. Designed for the "knurled" split-shaft
potentiometers.
Found on a variety of Marshall™ amps, including some JCM-800, JCM-900,
JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early
ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the
earlier MG series versions as well as other models.
Nothing perks up the tired looks of a road-worthy Marshall™ like a complete new
set of knobs. Older Marshalls typically have knobs where some of the
gold caps have fallen off, and the other gold caps have faded to look more like
silver than gold. It used to be a bit pricey to swap out the
complete set of knobs on some of the JCM900's, but with this
new set of aftermarket Marshall™ knobs, it's affordable. This
set of 10 knobs is perfect for many JCM900 series models with 10 control pots,
such as the 2101, 2501, 4100, 4101, 4102, 4500, 4501, and 4502.
Quality reproduction of the original Marshall™ knobs at half of the
cost. Since Marshall has recently changed the appearance of their original Marshall brand knobs (duller and more of an orange-gold color), we believe these reproduction knobs are now actually closer in appearance to the original Marshall knobs.
Part #MKCPT-10
$14.95
(Set of 10 knobs)
Click on photo for
larger view
KNOB
SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of
25. Excellent quality
aftermarket Marshall™ control knobs, push-on type,
set of 25 knobs. Designed for the "knurled"
type control shafts Nothing perks up the tired looks of a
road-worthy Marshall™ like a complete new set of knobs. Quality reproduction of the original Marshall™ knobs at half of the
cost. This set of 25 knobs is great for repair shops, at less than $1.00
per knob. Found on a variety of Marshall™ amps, including some JCM-800, JCM-900,
JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early
ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the
earlier MG series versions as well as other models.
Part #MKCPT-25
$24.95
(Set of 25 knobs)
Click on photo for
larger view
KNOB
SET, Revisit™ Quality REPRODUCTION of Marshall™ Knobs, Push-on Knurled, Set of
50. Excellent quality
aftermarket Marshall™ control knobs, push-on type,
set of 50 knobs. Designed for the "knurled"
type control shafts Nothing perks up the tired looks of a
road-worthy Marshall™ like a complete new set of knobs. Quality reproduction of the original Marshall™ knobs at half of the
cost. This set of 50 knobs is great for repair shops, at less than 80
cents
per knob. Found on a variety of Marshall™ amps, including some JCM-800, JCM-900,
JTM-30 series, JTM-60 series, JCM-600 series, 9001 and 9004 preamp, the early
ValveState models (8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280) and the
earlier MG series versions as well as other models.
Part #MKCPT-50
$39.95
(Set of 50 knobs)
Click on photo for
larger view
Revisit™ 6 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 6 ft LONG, IEC
CONNECTOR AT EQUIPMENT END. Common replacement cord for use on many
guitar amps, power amps, effects units, etc. Standard NEMA 5-15 plug
for North American use at 110-120 Volts AC. IEC connector at
equipment end. Used only in North America. Part #PC-300
$6.95
Click on photo for
larger view
Revisit™ 10 ft POWER CORD, DETACHABLE, 3-WIRE, 18ga, 10 ft LONG, IEC CONNECTOR AT EQUIPMENT END.
Replacement cord for many guitar amps, power amps, effects units, etc. 10 ft
length giveS extra flexibility in equipment placement, reduces use of extension
cords.
Standard NEMA 5-15 plug for North American
use at 110-120 Volts AC. IEC connector at equipment end.
Used only in North America. Part #PC-600
$10.95
Click on photo for
larger view
IEC POWER CONNECTOR, NON-FUSED, WIRED TYPE, SCREW ATTACHMENT TO PANEL Popular IEC type AC connector found in many amplifiers and effects units. Designed to mount in 0.8" x 1.10" rectangular panel hole. Screw holes are 1.57" apart, center-to-center. Connectors are for push-on terminals, or may be soldered. Rated at 10 amps. Part #P-S2-106
$2.95
Click on photo for
larger view
ROCKER
SWITCH, LIGHTED POWER, ORIGINAL Marshall™ , FOUND IN Marshall™ JCM900 SERIES For JCM900 series.. For most JCM800 models, see the SW-492.
For the JCM2000 and JVM series, see the SW-493. Has 4 electrical terminals on back of switch.1/4" push-on terminals, or solder directly to terminals. Rated 22A @ 125VAC, 16A @ 250VAC.15/16" x 1 1/16" x 1" deep. Internal neon lamp powered by 125VAC. Does your old Marshall™ power switch
from the JCM800 era have five terminals? See the SW-492
below, instead. Part #SW-491
$12.95
Click on photo for
larger view
ROCKER SWITCH, BLACK, USED AS STANDBY SWITCH IN Marshall™ JCM SERIES & OTHERS Has 4 electrical terminals on back of switch.1/4" push-on terminals, or solder directly to terminals. 15/16" x 1 1/16" x 1" deep. Part #SW-490
$8.50
Click on photo for
larger view
SAVE
WITH MULTIPACK! THIS SET CONTAINS BOTH the POWER AND the STANDBY ROCKER
SWITCHES, FOUND IN Marshall™ JCM SERIES & OTHERS Lighted power switch
has 4 electrical terminals on back of switch.1/4" push-on terminals, or solder directly to terminals. Rated 22A @ 125VAC, 16A @ 250VAC.15/16" x 1 1/16" x 1" deep. Internal neon lamp powered by either 125VAC or 250VAC.
Standby switch has 4 electrical terminals on back of switch.1/4" push-on terminals, or solder directly to terminals. 15/16"
x 1 1/16" x 1" deep. Part #SW-4901
$18.95
Click on photo for
larger view
Marshall™ Impedance/Mode Selector switch.
Correct replacement for PCB mount impedance and high-low mode
switch found on
the back of many Marshall™ JCM900 and
JCM2000 series amplifiers. Also used
as
The impedance switch in Marshall™ 4x12 Cabinets (such as the 1960 series
cabinets). Found in other British-made amplifiers and cabinets
as well. Marshall™ part number S208. Part #SW-4500
$13.95
Click on photo for
larger view
ORIGINAL REPLACEMENT CAP FOR FH-815 FUSE HOLDERS - Marshall™ Replacement CAP ONLY for mains and HT fuse holders found on the Marshall™
JCM900 series. Part #FH-204
$3.95
Click on photo for
larger view
ORIGINAL REPLACEMENT FUSE HOLDER - Marshall™ Replacement for mains and HT fuse holders found on the Marshall™ JCM900
series. Replacement fuse holder for the HT fuse only in the
larger TSL and DSL models
in the JCM2000 series
(TSL100, TSL122, DSL100, DSL50). Includes the FH-204 cap (above). Common failure item in Marshall™.
Designed to work with GMA type fuses (5mm x 20mm) Part #FH-830
$8.50
CAPACITOR, electrolytic 10uF @ 160V with axial leads.
Replaces 10uF @ 100V. Used in the Marshall JCM900 series amplifiers. Part #EL-CAP-10-160
$1.00
CAPACITOR, electrolytic 10uF @ 450V with axial leads. Used in the Marshall JCM900 series amplifiers. Part #EL-CAP-10-450
$3.50
CAPACITOR, electrolytic 33uF @ 450V with axial leads. Used in the Marshall JCM900 series amplifiers. Part #EL-CAP-33-450
$3.99
CAPACITOR, electrolytic 100uF @ 50V with radial leads. Used in
the low voltage power supply of Marshall JCM900 series amplifiers. Part #RAD-100-50
$0.39
CAPACITOR, electrolytic 1000uF @ 16V with radial leads. Used in
the low voltage power supply of Marshall JCM900 series amplifiers. Part #RAD-1000-16
$0.77
Click on photo for
larger view
CAPACITOR, F&T BRAND, AXIAL LEAD
ELECTROLYTIC, VARIOUS VALUES AND VOLTAGES AVAILABLE (SEE OPTIONS) Made
in Germany. Founded in 1948 by Heinz Fischer and Alfred Tausche, F&T Capacitors has over 75 years of experience in producing some of the finest
capacitors available today. F&T Caps are known for their great stability and
reliability. Values available include 10uF/500V, 16uF/475V, 22uF/500V,
30uF/500V, 47uF/500V, 80uF/450V, 100uF/100V, 100uF/450V, and 220uF/300V.
Choose capacitor value under the Select Option box. Part #FT-CAP-XX
Starting at
$4.95
Click on photo for
larger view
CAPACITOR, F&T BRAND, DUAL CAN 16uF+16uF @ 450V. Direct replacement for LCR type capacitors popular in Marshall™
and Vox™ amps. This is a dual can style capacitor
16uF/16uF rated at 450 volts. Solder terminals for attaching wire
leads. 1 3/8" diameter X 2" tall. Very low ripple.
Clamp may be ordered separately below.Made in Germany. Founded in 1948 by Heinz Fischer and Alfred Tausche,
F&T Capacitors has over 75 years of experience in producing some of the finest
capacitors available today. F&T Caps are known for their superior stability
and
reliability. Part #FT-1616
$17.95
Click on photo for
larger view
CAPACITOR, F&T BRAND, DUAL CAN 32uF+32uF @ 500V. Direct replacement for LCR type capacitors popular in Marshall™
JMP and JCM900 series amps. This is a dual can style capacitor
32uF/32uF rated at 500 volts. Solder terminals for attaching wire
leads. 1 3/8" diameter X 2" tall. Very low ripple.
Clamp may be ordered separately below.Made in Germany. Founded in 1948 by Heinz Fischer and Alfred Tausche,
F&T Capacitors has over 75 years of experience in producing some of the finest
capacitors available today. F&T Caps are known for their superior stability
and
reliability. Part #FT-3232
$18.95
CAPACITOR, F&T BRAND, DUAL CAN 50uF+50uF @ 500V Direct replacement for LCR type capacitors popular in Marshall™
JMP and JCM900 series amps. This is a dual can style capacitor
50uF/50uF rated at 500 volts. Solder terminals for attaching wire
leads. 1 3/8" diameter X 2" tall. Very low ripple.
Clamp may be ordered separately below.Made in Germany. Founded in 1948 by Heinz Fischer and Alfred Tausche, F&T Capacitors has over 75 years of experience in producing some of the finest
capacitors available today. F&T Caps are known for their great tone and
reliability. Part #FT-5050
$19.95
CAPACITOR, JJ ELECTRONIC, direct replacement for LCR type capacitors popular in Marshall™
JCM900 series amps. This is a dual can style capacitor
50uF/50uF rated at 500 volts. Solder terminals for attaching wire
leads. 1 3/8" diameter X 2" tall. Very low ripple.
Clamp may be ordered separately below.Made in the Slovak Republic in eastern Europe. Founded in 1993 by Jan
Jurco, JJ Electronic is a world-renowned manufacturer of vacuum tubes,
electrolytic capacitors and high-end audio amplifiers. Part #JJ-5050
$17.95
CAPACITOR CLAMP, for FT-1616, FT-3232, FT-5050, JJ-5050, or other 1 3/8" diameter can style
capacitors.
Part #CC-122
$2.50
RESISTOR, SANDBLOCK 470 OHM, 5 WATT.
Part #470W5
$0.99
RESISTOR, FLAMEPROOF, 1000 OHM, 5 WATT.
Commonly used as the screen grid resistor in many tube amps. Part #1000W5
TUBE RETAINER WITH SPRINGS, DESIGNED FOR 6L6 OR EL34 TUBES. USED IN Marshall™ AND MANY OTHER AMPS.
Part #TC-141
$3.49
Click on photo for
larger view
LARGE TUBE RETAINER WITH SPRINGS, DESIGNED FOR 6550 OR KT-88 TUBES.
Part #TC-143
$3.49
Click on photo for
larger view
OCTAL TUBE KEYWAY, SET OF 2 If you have a cherished octal power
tube or rectifier with a broken keyway, here is a great solution. By cleaning
the remainder of the broken keyway from the tube base and properly installing
this keyway replacement (a little dab of silicone sealant works great to hold it
in place), your tube can safely be reinstalled into your equipment.
These great tube-savers are sold in sets of 2. Note: When using an adhesive to secure the keyway to the tube base, DO NOT use a
water-based glue. Silicone sealant (RTV) which is acryllic-based or
butyl-based is fine. Latex sealant or hot-glue is NOT. Part #OTK8-2
$8.99
(for a set of 2 tube keyways)
Click on photo for
larger view
OCTAL TUBE BASE, SOLD
INDIVIDUALLY Octal tube bases are used to construct tube socket savers, solid-state
rectifiers, bias probes, etc. 8-pin plug with room inside the base
for circuitry and wiring. Sold individually. Part #OTB-100
$3.99 ea
Click on photo for
larger view
TUBE SOCKET, OCTAL 8-PIN, commonly used with the Octal Tube Base to build
bias probes, tube socket savers, tube extenders, etc. This socket
has no mounting bracket. Part #TS-8-810
$4.40
Click on photo for
larger view
PHENOLIC TUBE SOCKET FOR OCTAL TUBES. EXACT REPLACEMENT FOR VINTAGE FENDER, VINTAGE Marshall™ (including the JCM900 Series), and many others. Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes. For 1" to 1 1/8" hole. Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/2" apart.
Unlike some phenolic tube sockets on the market, this one fits the 1" hole found
in most vintage Fenders. Part #TS-8-600
$5.70
Click on photo for
larger view
PHENOLIC TUBE SOCKET FOR OCTAL TUBES. Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes. For 1 1/8" hole.
Bottom mounting (mounted from the inside of the chassis), mounting holes spaced 1 1/2" apart. Part #TS-8-250
$5.15
Click on photo for
larger view
TUBE SOCKET FOR MINIATURE 9-PIN TUBES. EXACT REPLACEMENT FOR MANY MAKES AND MODELS OF AMPS WITH HAND-WIRED TUBE SOCKETS. Fits 12AX7, 12AU7, 12AT7, 6BQ5, EL84 tubes. For 3/4" hole. Top mounting (mounted from the outside of the chassis), mounting holes spaced 1 1/8" apart. Designed to work with the TR-144 or TR-146 tube retainers, or the TS-325S tube shield. Part #TS-9-610
$2.49
Click on photo for
larger view
Marshall™
SMALL BRASS PAN-HEAD SCREWS WITH LOCK WASHERS AND NUTS (SET OF 6). Set
of 6 screws, brass, 3/8" (9.5mm) long, slotted pan head - head is 5.4mm in diameter, 4-40
thread, with lock washer and nut. Used to mount preamp tube sockets
and impedance selectors in classic Marshall™
amps.
Part #MSBS-6
$1.99
(for a pack of 6 screws, 6 lock washers and 6 nuts)
Click on photo for
larger view
Marshall™
SMALL BRASS ROUND-HEAD SCREWS WITH LOCK WASHERS AND NUTS (SET OF 6). Set
of 6 screws, brass, 1/2" (12.7mm) long, slotted round head - head is 5.4mm in diameter, 4-40
thread, with lock washer and nut. Used to mount impedance selectors
and IEC power cord connectors in classic Marshall™
amps.
Part #MLBS-6
$2.49
(for a pack of 6 screws, 6 lock washers and 6 nuts)
Click on photo for
larger view
Marshall™
MEDIUM BRASS ROUND-HEAD SCREWS WITH LOCK WASHERS AND NUTS (SET OF 8). Set
of 8 screws, brass, 3/8" (12.7mm) long, slotted round head - head is 6.1mm in diameter,
6-32
thread, with lock washer and nut. Used to mount power tube sockets,
capacitor cans and ground lugs in classic Marshall™
amps.
Part #MMBS-8
$2.99
(for a pack of 8 screws, 8 lock washers and 8 nuts)
Click on photo for
larger view
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL
WITH 9-PIN TUBE SOCKET AND INTEGRAL TUBE SHIELD BASE . Spring in top of shield fits over the
tube. Fits 12AX7A and similarly sized preamp tubes. 9-Pin tube
socket is made of sturdy Micalex. Replacement for Fender™ and many other brands. Holes in base spaced 1 1/8" apart.
Requires 3/4" hole in chassis. Solder lugs for wire connection to tube
socket.
Shield, base and socket. Part #TS-370
$4.99
Click on photo for
larger view
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL.
Includes new base, if needed. Spring in top of shield fits over the
tube. Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender™ and many other brands. Holes in base spaced 1 1/8" apart.
Shield and base only - socket not included. Part #TS-325S
$2.29
Click on photo for
larger view
TUBE SHIELD, BAYONET "PUSH AND TWIST" TYPE, ALUMINUM, 1 15/16" TALL,
SET OF 6.
Includes new bases, if needed. Spring in top of shield fits over the
tube. Fits 12AX7A and similarly sized preamp tubes. Replacement for Fender™ and many other brands. Holes in base spaced 1 1/8" apart.
This is a great kit to replaced all 6 of the tube shields in many Fender™ amps
with 6 preamp tubes. Shield and base only - socket not included. Part #TS-325S-6
$12.95
(TUBE NOT INCLUDED)
Click on photo for
larger view
Revisit™ PRE-AMP TUBE DAMPER
RINGS.
Use two (or three) of these rings around a pre-amp tube to reduce noise and
microphonics. An economical alternative to more expensive tube dampers.
Will withstand high temperatures of pre-amp tubes, reusable when you change
tubes. Set of 6 rings - will equip either 2 or 3 tubes, depending on the number of rings you choose for each tube. Note: Tube shields will not fit over the damper rings, and must be removed from the tubes.These
dampers are NOT for 9-pin power tubes, such as the EL84 or 6BQ5. Part #PTD-6
$4.95
(Set of 6 rings)
Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8DB2C1D.
Short Tank, Medium Decay, input impedance 310 ohms, output 2575 ohms, insulated
input and grounded output. Designed for horizontal
mounting, open side up. Primarily found in the Marshall™ 4100,
4101, 4102, 4500, 4501, 4502 in situations where the tank is mounted "upside
down".
See explanation of Korean-made Accutronics Reverb Tank numbering system here.
See a chart which lists AC impedance and DC resistance measurements for reverb
tanks here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.
View the 2-year warranty details
here. Part #8DB2C1A
"Bringing back the sound of vintage Accutronics tanks"
$42.89
Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8DB2C1D.
Short Tank, Medium Decay, input impedance 310 ohms, output 2575 ohms, insulated
input and grounded output. Mounts on vertical wall, long axis
horizontal, connectors down.
Primarily found in the Marshall™ 4100, 4101, 4102, 4500, 4501, 4502, 5150,
5205, 8080, 8100, 8240, AS50, AS50R, AS80R, AVT50, AVT50H, JCM600, JCM602,
JTM310, JTM312, JTM610, JTM612, JTM615, JTM622, MA50C, G25R, G50RCD, VS100R,
VS100RH, VS102R, VS230, VS232, VS265, and VS65R.
See explanation of Korean-made Accutronics Reverb Tank numbering system here.
See a chart which lists AC impedance and DC resistance measurements for reverb
tanks here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.
View the 2-year warranty details
here. Part #8DB2C1D
"Bringing back the sound of vintage Accutronics tanks"
$42.89
Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8DB3C1B.
Short Tank, Long Decay, input impedance 310 ohms, output 2575 ohms, insulated
input and grounded output. Mounts horizontal, open side down. Primarily used by
Marshall™ JCM900.
See explanation of Korean-made Accutronics Reverb Tank numbering system here.
See a chart which lists AC impedance and DC resistance measurements for reverb
tanks here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.
View the 2-year warranty details
here.
Part #8DB3C1B
"Bringing back the sound of vintage Accutronics tanks"
$42.89
Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8FB2B1F. Short
Tank, Medium Decay, input impedance 1925 ohms, output 2575 ohms, grounded input
and insulated output. Mounts on vertical wall with long axis vertical, output side
up.
See explanation of Korean-made Accutronics Reverb Tank numbering system here.
See a chart which lists AC impedance and DC resistance measurements for reverb
tanks here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.
View the 2-year warranty
details here. Part #8FB2B1F
"Bringing back the sound of vintage Accutronics tanks"
$42.89
Click on photo for larger view
Revisit™ Reverb Tank, 9" long, 3 spring, equivalent to Accutronics 8FB3C1B. Short
Tank, Long Decay, input impedance 1925 ohms, output 2575 ohms, insulated input
and grounded output. Mounts horizontal, open side down.
See explanation of Korean-made Accutronics Reverb Tank numbering system here.
See a chart which lists AC impedance and DC resistance measurements for reverb
tanks here.
Unlike some tanks, Revisit™ Reverb Tanks include the soft mounting grommets to acoustically decouple the outer channel from the amplifier cabinet.
View the 2-year warranty
details here. Part #8FB3C1B
"Bringing back the sound of vintage Accutronics tanks"
$42.89
Click on photo for
larger view
Rubber mounting grommets for reverb tanks, package of four.
Provides shock absorption for tanks mounted directly to the inside of a wooden
amp cabinet. Mounting Hole Diameter = 3/8" Outer Diameter = 1/2"
Part #RRG-4
$1.99
(For a pack of 4 grommets - In Stock)
Click on photo for
larger view
3 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices.
Dual cable, excellent shielding properties, 3 feet long.
Part #RC-173
$8.95
In Stock
Click on photo for
larger view
4 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices.
Dual cable, excellent shielding properties, 4 feet long.
Part #RC-174
$8.95
In stock
Click on photo for
larger view
5 foot Revisit™ right angle RCA cables for Reverb Tanks and other electronic devices.
Dual cable, excellent shielding properties, 5 feet long.
Part #RC-175
$8.95
In stock
Click on photo for
larger view
Marshall™ CORNERS, FRONT OF
CABINET
Front corner set, ¾" radius. Includes 12
gold rivets for attaching to cabinet. For heads, combos and straight
speaker cabinets. Will not fit slanted speaker cabinets,
such as the 1960A. For slanted cabinets, see the MC-1092 set.
Part #MC-1091
$10.95
(For a set of 4 corners with 12 rivets)
Under new ownership (Zounds, Inc. of Sweden), Marshall is currently not shipping
parts. See the RC-1091 as a substitute set of corners.
Click on photo for
larger view
Revisit™
Quality Reproduction of Marshall™ CORNERS, FRONT OF
CABINET
Front corner set, ¾" radius. Includes 12
gold rivets for attaching to cabinet. For
Marshall™
heads, combos and straight
speaker cabinets. Replace your
Marshall™
corners with quality parts at 25% less than Marshall™
prices.
Will not fit slanted speaker cabinets,
such as the 1960A. For slanted cabinets, see the MC-1092 set.
Part #RC-1091
$7.95
(For a set of 4 corners with 12 rivets)
Click on photo for
larger view
Marshall™
SPECIAL CORNERS, FRONT OF
SLANTED SPEAKER CABINETS
Front corner set, ¾" radius. Includes 12
gold rivets for attaching to cabinet. Two top angled corners for the
left and right top corners of angled speaker cabinets, and two straight corners for the bottom front
corners. For slanted speaker cabinets ONLY,
such as the 1960A, MG412AG, MX412A Part #MC-1092
$16.95
(For a set of 4 corners with 12 rivets)
Under new ownership (Zounds, Inc. of Sweden), Marshall is currently not shipping
parts.
Click on photo for
larger view
Marshall™ CORNERS, REAR OF
CABINET
Rear corner set, ¾" radius. Includes 16
gold rivets for attaching to cabinet. For heads, combos and speaker
cabinets.
Part #MC-1090
$11.95
(For a set of 4 corners with 16 rivets)
Under new ownership (Zounds, Inc. of Sweden), Marshall is currently not shipping
parts. See the RC-1090 as a substitute set of corners.
Click on photo for
larger view
Revisit™
Quality Reproduction of Marshall™ Corners, Rear of
Cabinet
Rear corner set, 3/4" radius. Includes
16
gold rivets for attaching to cabinet. For Marshall™
heads, combos and
speaker cabinets. Replace your
Marshall™
corners with quality parts at 25% less than Marshall™
prices.
Part #RC-1090
$8.95
(For a set of 4 rear corners with 16 rivets)
Click on photo for
larger view
Marshall™
GOLD RIVETS
For attaching Marshall™ corners to cabinets. Gold, package of 12 rivets. Part #MR-109
$4.95
(For a set of 12 gold rivets)
Click on photo for
larger view
Marshall™
SILVER RIVETS
For attaching Marshall™ corners to cabinets. Silver, package of 12 rivets. Part #MR-109S
$4.95
(For a set of 12 silver rivets)
Click on photo for
larger view
MARSHALL™
HANDLE STRAP FOR TSL100 HEAD. Original Marshall™ handle strap for the
MAH-294 Handle. Sold
individually. Includes metal strap insert and rubber strap.
Genuine Marshall. Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Save money by replacing only the worn strap! Ends
and clamps not included.
Part #MHS-294
$9.95
(each)
Click on photo for
larger view
MARSHALL™ END CAPS FOR MAH-294 HANDLE.
Handle end caps for the MAH-294 Handle. Sold in sets of two caps. NOTE: DOES NOT HAVE THE MARSHALL LOGO ON THE CAPS.
Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Save money by replacing only the parts
the handle needs! Strap, screws and clamps not included. Set
of two end caps.
Part #MHC-294-2
$6.95
(for a set of 2 end caps)
Click on photo for
larger view
MARSHALL™ INTERNAL END CLAMPS FOR MAH-294 HANDLE.
Handle internal clamps for the MAH-294 Handle. Sold in sets of two end clamps.
Genuine Marshall.
Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Save money by replacing only the parts
the handle needs! Strap, black end caps, screws and strap not included. Note:
These are unfinished metal caps - designed to be used only with the
snap-on MHC-294-2 end caps. Set
of two end clamps.
Part #MIC-294-2
$4.99
(for a set of 2 end clamps)
Click on photo for
larger view
Marshall™
METRIC HANDLE SCREWS
Pack of 2 metric handle screws for Marshall™
MAH-294 handle. Original Marshall™ , designed to work with the OEM
metric T-Nuts. Set of 2 Flat-head counter-sunk Phillips,
M5 x 0.8, length 25 mm.
Found primarily on
JCM900, JCM2000, larger Valvestate, and JVM series amps.
Part #SC-404
$1.99
(for a pack of 2 Marshall™ metric screws)
Click on photos for
larger view
(Assembled)
Marshall™
HANDLE Genuine Marshall™ Handle for modern heads and combo amps. Used
primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Original Marshall™ part number M-PACK-00031. Kit contains:
(2) Countersunk screws - M5 x 0.8, overall
length of 25 mm
(2) Mounting brackets
(2) Black bracket covers with Marshall™
logo
(1) Rubber handle with metallic insert
Center-to-center screw mounting distance
is 8 3/8" (213mm).
Overall length of assembled and mounted
handle is 101/4"(260mm).
Replacement screws are the Marshall™ SC-404
screws, below
Part #MAH-294
$21.95
Click on photos for
larger view
(Assembled)
Marshall™
AFTERMARKET HANDLE Identical to the Genuine Marshall™ Handle MAH-294, except does not
have the "Marshall" name imprinted on the end caps. Save compared to the price of the original Marshall™ handle. For modern heads and combo amps. Used
primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Replaces Original Marshall™ part number M-PACK-00031
or stock number MAH-294. Kit contains:
(2) Countersunk screws - M5 x 0.8, overall
length of 25 mm
(2) Mounting brackets
(2) Black bracket covers (no Marshall™
logo)
(1) Rubber handle with metallic insert
Center-to-center screw mounting distance
is 8 3/8" (213mm).
Overall length of assembled and mounted
handle is 101/4"(260mm).
Replacement screws are the Marshall™ SC-404
screws, below
Part #RAH-294
$15.99
Click on photo for
larger view
Marshall™
METRIC HANDLE SCREWS
Pack of 2 metric handle screws for Marshall™
MAH-294 handle. Original Marshall™ , designed to work with the OEM
metric T-Nuts. Set of 2 Flat-head counter-sunk Phillips,
M5 x 0.8, length 25 mm.
Found primarily on
JCM900, JCM2000, larger Valvestate, and JVM series amps.
Part #SC-404
$1.99
(for a pack of 2 Marshall™ metric screws)
Click on photo for
larger view
Marshall™ LOGO, WHITE PLASTIC, 9" LONG
- TSL122 The 9 inch long Marshall™ logo - medium size. As used on the
TSL122 combo. This logo is 9" long - please measure the old logo in order to ensure that you
order the correct size. Part #ML-901
$38.95
Availability date uncertain. Has been on backorder from Marshall since
May, 2023.
Click on photo for
larger view
Marshall™ LOGO, WHITE PLASTIC,
11" LONG - TSL100 The 11 inch long Marshall™ logo - large size. As used on the 2100,
2205, 2203, 2204, 2210, 2550, 2553, 2554, 2558, 4102, 4001, 4210, 4211, 4212,
4100, 4101, 4103, 4010, 4500, 5213, 5210, 5212, DSL100, 1986, 1960B
cabinet, 1959JMP, 1936, TSL100, 6100, 6101, JCM1959, 2558V, 3005, 2555SL,
AS1960, 2100SLX, TSL60, 1987JCM, DSL50, 3005, 1960AX, and some other models This logo is
11" long - please measure the old logo in order to ensure that you order the
correct size. Part #ML-1101
$39.95
Availability date uncertain. Has been on backorder from Marshall since
May, 2023.
Click on photo for
larger view
Marshall™
TOP VENT, 8 SCREW OR RIVET HOLES, MOST JCM800 AND JCM900 HEADS This original Marshall vent is for most JCM800 and JCM900 heads from the
1980s and 1990s. Check the measurement of your existing vent - the MV-211
vent measures 17 5/8" x 3". Rivets/screws not included. Part #MV-211
$13.95
Availability date uncertain. Has been on backorder from Marshall since
December, 2023.
Click on photo for
larger view
STAINLESS STEEL CHASSIS SCREWS WITH WASHERS, Marshall™ METRIC Replacements for the standard M6 metric screws used to hold the chassis in
virtually every Marshall™ head. Washers included. Package of 4
stainless steel screws, with 4 washers. Part #MCB-4
$3.99
(Set of 4 screws w/washers)
Click on photo for
larger view
STAINLESS STEEL
COMBO CHASSIS SCREWS, Marshall™ METRIC (NOT BLACK!) SET OF 4
SCREWS. Unpainted replacements for the standard M6 metric screws used to hold the chassis in virtually every
larger Marshall™
combo (typically 50 watts & up). Note that these
screws are plain stainless steel - NOT BLACK LIKE the ORIGINALS. You may paint the top
black if you choose. We recommend that you only paint the top - do not
paint the threads. 35mm long, replaces Marshall part number MESCRW00001.
Found in the JTM610, JTM612, JTM612, JTM615, JTM622, JCM601, JCM602, 2101, 2501,
2502, 4101, 4102, 4501, 4502, TSL601, TSL601, and TSL122. Set of 4 screws.
See the CW-400-4 washers below for a set of suitable washers. Part #MCS-5140-4
$2.29
(Set of 4 screws)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 4. OD 1/2", ID 3/16"
Typically found on larger combo amp cabinets and 4x12 cabinets, such as
Marshall™ . Set of 4 washers.
Part #CW-400-4
$0.99
(for a set of 4 washers)
Click on photo for
larger view
Marshall™ CHASSIS WASHERS Replacements for the standard washers used with the MCB-4 chassis screws under virtually every Marshall™
head. Note: Not for Marshall Combo amps.
Also fits Orange and Trace Elliot amps which use chassis bolts to secure the
chassis. Package of 4 washers. Part #MCW-4
$1.99
(Set of 4 washers)
Click on photo for
larger view
CHASSIS CAGE NUTS, Marshall™ M6 METRIC Replacements for the standard M6 metric cage nuts used on the chassis in virtually every Marshall™ head. Package of 4 cage nuts. Mates with the MCB-4
or MCS-5140-4 screws, above. Part #MCN-4
$4.59
(Set of 4 nuts)
Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS
(SET OF 8) FOR CLOSED BACK CABINETS (SUCH AS Marshall™, Fender™ Bassman,
Bandmaster, etc ). Set
of 8 screws, Stainless Steel, 1 3/4" long, Phillips, oval head. Use with the
CW-400-8 cup washers.
Part #SC-400-8
$1.99
(for a pack of 8 screws)
Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS
(SET OF 17) FOR CLOSED BACK CABINETS (SUCH AS Marshall™, Fender™ Bassman,
Bandmaster, etc ). Set
of 17 screws, Stainless Steel, 1 3/4" long, Phillips, oval head. Use with the
CW-400-17 cup washers. A set of 17 screws completely replaces
all of the screws on most Marshall™ 4x12 cabinets, including the 1960 models.
Part #SC-400-17
$3.89
(for a pack of 17 screws)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 17. OD 1/2", ID 3/16"
Typically found on larger combo amp cabinets and 4x12 cabinets, such as
Marshall™ . Set of 17 washers. Some of the larger Marshall
4x12 cabinets, such as certain model 1960 cabinets, have 17 screws and washers in the back
panel.
Part #CW-400-17
$3.79
(for a set of 17 washers)
Click on photo for
larger view
Marshall™
HEAD BACK PANEL STAINLESS STEEL SCREWS AND WASHERS
(SET OF 4) FOR FULL SIZE HEADS. Set of 4 screws, Stainless Steel, 1 1/2" long, Phillips, oval head, with matching cup washers.
Fits most large Marshall™ heads starting in the 1990s, including the JCM-800,
JCM-900, JCM-2000 and JVM series.
Note: The screw heads in this package have a slight oval shape, as opposed
to many Marshall™ head back panel screws which have a flat head. This oval
shape helps improve the "bite" of the screwdriver, and helps prevent the screw
head from being mangled over time.
Part #MBP-4
$1.49
(for a pack of 4 screws and 4 washers)
Click on photo for
larger view
Marshall™ STYLE FOOTSWITCH Revisit™ aftermarket replacement for the original Marshall™ footswitch -
same quality, just without the Marshall™ logo and Marshall™ price tag.
Sturdy metal construction. Mono 1/4" Plug, 16 ft. cable.
Standard design - footswitch operation shorts the tip to the sleeve - will work
with other makes and models of amplifiers as well as Marshall™.
Replaces Marshall™ stock numbers P801 and PEDL-00008. Works with the
Marshall™ models 1962, 8040, 2555, 2550, 2558, 2553, 2554. JTM60
models: JTM600-610-615-612-622. JCM600 models 600-601-602.
JCM900 models 2100-2500-2501-2101-2502. JTM30 models 310-312.
DBS models 7200-7400-72410-72115. Rackmount amps 9100-9200. MG
Series I model G50RCD. IBS models 3520-5522-3540. Part #FBS-470
$29.95
Click on photo for
larger view
Marshall™ STYLE DUAL FOOTSWITCH Revisit™ aftermarket replacement for the original Marshall™ dual footswitch - same quality, just without the Marshall™ logo
and Marshall™ price tag. Sturdy metal construction. Standard design - operation of one of the footswitches shorts the tip to the sleeve, while the other switch shorts the ring to the sleeve.
Latching switches. Replaces Marshall™ stock number P802, P803, P804,
P805, PEDL-00009, PEDL-00010, PEDL-00015, PEDL-00017. Fits the
Marshall™ JCM900 series: 4100-4500-4101-4501-4102-4502. The
JCM800 series 2210-2205-4210-4212-4211. The ValveState series:
8080-8100-8200-8280-8240. The MG Series 1: G80RCD-G100RCD. The Acoustic Soloist: AS80R.
Can work with other makes and models of amplifiers as well as Marshall™
- commonly used on most models of Trace Elliot guitar amps (not the bass amps,
however). Also used on Gibson™ Goldtone amplifiers, and Framus Ruby
I, Ruby II, CS, and Red Rogue models.
1/4" Stereo plug, 16 ft. cable. Will also work on the
Fender 1990s and 2000s Reissue 65 Twin-Super-Deluxe-Princeton Reverb
amps. Part #FBS-471
$37.95
Click on photo for
larger view
UNIVERSAL STYLE
DUAL FOOTSWITCH WITH REMOVABLE CABLE. Revisit™
replacement for foot switch boxes with stereo 1/4" plug for the amplifier
connection. 10 foot long cable is removable from the foot switch box - has a stereo 1/4" plug
for connection at both the foot switch end and the amplifier end.
Replaces Marshall™ stock number P802, P803, P804, P805, PEDL-00009, PEDL-00010,
PEDL-00015, PEDL-00017. Fits the Marshall™ JCM900 series:
4100-4500-4101-4501-4102-4502. The JCM800 series
2210-2205-4210-4212-4211. The ValveState series:
8080-8100-8200-8280-8240. The MG Series 1: G80RCD-G100RCD. The Acoustic Soloist: AS80R. Includes the dual footswitch box and the
stereo cable (10 ft).
Advantages of the removable cable include:
Easy to replace cable - no disassembly or
soldering needed
Easy to change to a different
configuration footswitch by changing the cable (for example, to a mono
Y-cord for Roland amps)
Cable has metal 1/4" plugs with spring
strain reliefs for durability
Part #FBS-671
$44.95
Click on photo for
larger view
Marshall™ STYLE JACK PLATE, STEREO / MONO
Marshall™ style reproduction jack plate as found on the
Marshall™ 1960A, 1960B, Vintage Modern 425A or 425B Marshall™ 4x12
cabinets. Replaces Marshall part number M-196X-50-01. Includes
speaker wires terminated in 1/4" push-on connectors. Made in the USA
by Mojo.
Part #JP-800R
$49.95
Click on photo for
larger view
Complete
Genuine Marshall™ JACK PLATE, STEREO / MONO
Marshall™ jack plate as found on the
Marshall™ 1960A, 1960B, Vintage Modern 425A or 425B Marshall™ 4x12
cabinets. Marshall part number M-196X-50-01.
Part #JP-800
$69.95
CURRENTLY UNAVAILABLE FROM MARSHALL. USE JP-800R
(ABOVE) AS A REPLACEMENT.
Click on photo for
larger view
Marshall™
JACK PLATE REPAIR KIT
Replaces the common failure parts on
the JP-800 mono/stereo jack plate (shown above) as found on the 1960A, 1960B,
Vintage Modern 425A or 425B Marshall™ 4x12
cabinets. Kit contains both jacks and a new mono/stereo select
switch. If the plastic housing and the PC board are intact, this kit
replaces all of the functional components on the jack plate.
Part #RK-800
$14.95
Strat™, Stratocaster™, Esquire™, Telecaster™, Tele™, Jazzmaster™, Jaguar™, Mustang™, P.Bass™, J.Bass™ and Fender™ are registered trademarks of Fender™ Musical Instruments. The replacement necks and bodies are for a Fender™ or Squier™ by Fender™ guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster™, Telecaster™, J.Bass™, P.Bass™ and Tele™ Bass are registered trademarks of Fender™ Musical Instruments Co.
Peavey™ is a registered trademark of Peavey™ Electronics Corporation.
Marshall™ is a registered trademark of Marshall™ Amplification Plc.
Mesa Boogie™ is a registered trademark of MESA/Boogie™ Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.
JACK,
1/4", MONO PC MOUNT PLASTIC, BRITISH STYLE WITH CHROME NUT AND CHROME TRIM RING
Complete Marshall™ Potentiometer Kit, 8 SINGLE GANG POTS
AND 1 DUAL GANG POT.
ORIGINAL Marshall™ REPLACEMENT PARTS.
KNOB, Revisit™ Quality Reproduction of Marshall™ Knob, Push-on Knurled, Single
Knob.
Excellent quality aftermarket Marshall™ control knobs, push-on type.
Designed for the "knurled" type control shafts.
Black with gold top. Used on the
JCM-900 series amplifiers.
Since Marshall™ has recently changed the appearance of their original
Marshall™ brand knobs (duller and more of an orange-gold color), we believe
these reproduction knob are now actually closer in appearance to the original
Marshall™ knobs.
CAPACITOR, F&T BRAND, AXIAL LEAD
ELECTROLYTIC, VARIOUS VALUES AND VOLTAGES AVAILABLE (SEE OPTIONS) Made
in Germany. Founded in 1948 by Heinz Fischer and Alfred Tausche, F&T Capacitors has over 75 years of experience in producing some of the finest
capacitors available today. F&T Caps are known for their great stability and
reliability. Values available include 10uF/500V, 16uF/475V, 22uF/500V,
30uF/500V, 47uF/500V, 80uF/450V, 100uF/100V, 100uF/450V, and 220uF/300V.
Revisit™ PRE-AMP TUBE DAMPER
RINGS.
Use two (or three) of these rings around a pre-amp tube to reduce noise and
microphonics. An economical alternative to more expensive tube dampers.
Will withstand high temperatures of pre-amp tubes, reusable when you change
tubes. Set of 6 rings - will equip either 2 or 3 tubes, depending on the number of rings you choose for each tube. Note: Tube shields will not fit over the damper rings, and must be removed from the tubes. These
dampers are NOT for 9-pin power tubes, such as the EL84 or 6BQ5. 
Marshall™ STYLE JACK PLATE, STEREO / MONO
Complete
Genuine Marshall™ JACK PLATE, STEREO / MONO
WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.