Click on photo for
larger view |
 ROCKER
SWITCH, LIGHTED POWER, ORIGINAL Marshall™ , FOUND IN Marshall™ JCM900 SERIES
For JCM900 series.. For most JCM800 models, see the SW-492 below.
For the JCM2000 and JVM series, see the SW-493. Has 4 electrical terminals on back of switch.
1/4" push-on terminals, or solder directly to terminals. Rated 22A @ 125VAC, 16A @ 250VAC. 15/16" x 1 1/16" x 1" deep. Internal neon lamp powered by 125VAC. Does your old Marshall™ power switch
from the JCM800 era have five terminals? See the SW-492
below, instead.
Part #SW-491 |
$12.95 |
|
Click on photo for
larger view |
 ROCKER SWITCH, LIGHTED POWER,
Revisit™ REISSUE,
FOUND IN Marshall™ JCM800 and LATER JMP SERIES - 5 TERMINALS
Most JCM800 and late JMP series power switches have 5 terminals
 on the back of the
switch. These switches were originally made by Arrow for Marshall,
but have been unavailable for many years. For those switches with 5 terminals, this
Revisit™ switch is the correct
replacement. The terminal locations are a mirror image of the
original, but we have a cheat sheet
to show you how to easily wire the new switch. Has
5 electrical terminals on back of switch.
1/4" push-on terminals, or solder directly to terminals. Rated 20A @ 125VAC, 16A @ 250VAC. 15/16" x 1 1/16" x 1" deep. Internal neon lamp powered by 125VAC.
For newer JCM900 and JCM2000 series with 4 terminals on the
power switch, see the SW-491 switch above.
Part #SW-492 |
$18.95 |
|
Click on photo for
larger view |
ROCKER SWITCH, BLACK, USED AS STANDBY SWITCH IN Marshall™ JCM SERIES & OTHERS
Has 4 electrical terminals on back of switch.
1/4" push-on terminals, or solder directly to terminals. 15/16" x 1 1/16" x 1" deep.
Part #SW-490 |
$8.50 |
|
Click on photo for
larger view |
SAVE
WITH MULTIPACK! THIS SET CONTAINS BOTH the POWER AND the STANDBY ROCKER
SWITCHES, FOUND IN Marshall™ JCM900 SERIES & OTHERS
Lighted power switch
has 4 electrical terminals on back of switch.
1/4" push-on terminals, or solder directly to terminals. Rated 22A @ 125VAC, 16A @ 250VAC. 15/16" x 1 1/16" x 1" deep. Internal neon lamp powered by either 125VAC or 250VAC.
Standby switch has 4 electrical terminals on back of switch.
1/4" push-on terminals, or solder directly to terminals. 15/16"
x 1 1/16" x 1" deep.
Part #SW-4901 |
$18.95 |
|
Click on photo for
larger view |
ROCKER SWITCH, LIGHTED POWER,
ORIGINAL Marshall™ , FOUND IN Marshall™ JVM, DSL, and JCM2000 SERIES Used in the
later versions of the TSL100, TSL122, DSL100, DSL50, DSL40, later versions of
the DSL201 and DSL401, JVM210H, JVM410H, JVM215C, etc. Also found in the
DSL-5, DSL-15, and the Mode 4 MF-350. Has 4 electrical terminals on back of switch.
1/4" push-on terminals. Rated 16A. For use on 125VAC
or 250VAC. 15/16" x 1 1/16" x 1" deep. Internal
neon lamp. Original
Marshall part number B8C75184.
Part #SW-493C
|
$11.95 |
|
Click on photo for
larger view |
ROCKER SWITCH,
STANDBY,
ORIGINAL Marshall™ , FOUND IN Marshall™ JVM, JCM2000, DSL, TSL SERIES
Used in the later versions of the TSL100, TSL122, DSL100, DSL50, DSL40, later
versions of the DSL201 and DSL401, JVM210H, JVM410H, JVM215C, etc. Has 4 electrical terminals on back of switch.
1/4" push-on terminals. Rated 16A. 15/16" x 1 1/16" x 1" deep. Original
Marshall part number B8B64025B.
(For the similar standby switch used in previous model series such as the
JCM-900, early versions of the TSL and DSL series, see the SW-490 switch.)
Part #SW-490C |
$9.95 |
|
Click on photo for
larger view |
ROCKER SWITCH,
STANDBY,
WHITE, ORIGINAL Marshall™ , FOUND IN Marshall™ JVM, JCM2000, DSL, TSL SERIES
Used in the later versions of the TSL100, TSL122, DSL100, DSL50, DSL40, later
versions of the DSL201 and DSL401, JVM210H, JVM410H, JVM215C, etc. Has 4 electrical terminals on back of switch.
1/4" push-on terminals. Rated 16A. 15/16" x 1 1/16" x 1" deep. (For the similar standby switch used in previous model series such as the
JCM-900, early versions of the TSL and DSL series, see the SW-490 switch.)
This switch is priced to sell!
Part #SW-490CW |
$2.50 |
|
Click on photo for
larger view |
ROCKER SWITCH,
HI POWER/LOW POWER +
STANDBY,
ORIGINAL Marshall™. FOUND IN Marshall™
SC20C, SC20H, 2525H, 2525C, DSL100HR, DSL40CR. Has 6 electrical terminals on back of switch. MATTE
FINISH (NOT SHINY)
1/4" push-on terminals. Now in stock and ready to rock! Rated 16A. 15/16" x 1 1/16" x 1" deep.
Only used in the SC20C, SC20H, 2525H, 2525C, DSL100HR and DSL40CR.
Part #SW-496 |
$9.95
|
|
Click on photo for
larger view |
MARSHALL
POWER SWITCH FOR VALVESTATE SERIES II AMPS
Power switch for the second ValveState series, including models VS15, VS30R, VS65R, VS100R, VS100RH, VS102R, VS230, VS232 AND VS265. Also for the Bass State 150. Marshall reference numbers S540, S1603, and SW1008.
Switch button not included. The button for this switch is our stock
number K-108. NOTE: This switch does not have the 4 pin
connections on the bottom, so it is necessary to run wires from the 4 terminals
on top (marked in the photo with yellow arrows) to the PC board. It
does have the anchoring pins on the front bracket which are soldered to the PC
board.
Part #SW-160 |
$8.95 |
|
Click on photo for
larger view |
MARSHALL
POWER SWITCH BUTTON FOR VALVESTATE SERIES II AMPS
Power switch button for the second ValveState series,
including models VS15, VS30R, VS65R, VS100R, VS100RH, VS102R, VS230, VS232 AND
VS265. Also for the Bass State 150. Marshall reference numbers SW1008KNOPF. Fits the
SW-160 power switch.
Part #K-108 |
$2.50 |
|
Click on photo for
larger view |
ORIGINAL Marshall™ MINI ROCKER SWITCH FOR Marshall™ MG SERIES
- MARKED 0-1 FOR ON/OFF
DPDT Mini Rocker Switch. Has 4 electrical terminals on back of switch.
Face of switch marked with "0" and "1" for on/off. Original Marshall™ replacement. 0.51" x 0.76" mounting hole diameter, 10A-125 VAC,
6A-250VAC, DPST with .187" tabs.
Part #SW-489 |
$3.95 |
|
Click on photo for
larger view |
ORIGINAL
Marshall™ MINI ROCKER SWITCH FOR Marshall™ MG SERIES - LIGHTED
DPDT Mini Rocker Switch with internal
light. Has 4 electrical terminals on back of switch.
Red lighted version - easier to see than the tiny LED Marshall™ originally
provided as a power-on light. 0.51" x 0.76" mounting hole diameter, 10A-125 VAC,
6A-250VAC, DPST with .187" tabs. To ensure that the light
works properly, make sure that the terminals directly behind the "1" on the
rocker portion feed the power transformer, while the terminals behind the "0"
are connected to the incoming power source.
Part #SW-489L |
$4.95 |
|
Click on photo for
larger view |
ROCKER
SWITCH, HARTKE™, OTHERS, LARGE WIDE BLACK
Has 4 electrical terminals on back of switch
(DPST). Termination is 0.187" (4.8mm) push-on terminals. Made for 0.73" H x 0.85" W mounting
hole (19.0mm X 22mm). Rated 15A @ 125VAC.
Commonly found on Hartke™ amp models HA1400, HA2500, HA3500C, HA4000, HA5000,
HA5500, HA7000 and other models.
Hartke™ part number 8-S310BBIWQ420.
May also be used for the discontinued Marshall™
SWTM0030 power switch found on the Marshall™
AVT50, but note that this switch is not lighted like the original Marshall™
switch.
Part #SW-1802 |
$6.95 |
|
Click on photo for
larger view |
SWITCH, TOGGLE, DPST - Used in Marshall™,
Orange™
-and Trace Elliot™.
Rated at 15A, 125/250VAC. Two position (on/off), double pole (DPST), 4
terminals. Fits
1/2" chassis hole. Solder terminals or push-on terminals. Found
in Marshall™
Reissue models such as the 1959HW, 1959SLP, JTM45 (2245), 2245THW, 1987X, 2061X and 1974X. Original Marshall™
part number SWTM-00021. Found in Orange
AD30, AD200, TH50, and TH200. Found in Trace Elliot Speedtwin C30, Trident,
Bonneville, Velocette, Velo 12R, Velo Twin and V-Type tube amps.
Also found in some Hiwatt™
and Vox™
amps.
Part #SW-641 |
$24.95 |
|
Click on photo for
larger view |
ORIGINAL
Marshall™ PUSH SWITCH
DPDT Mini Short-Throw Push Switch. Has
6 electrical terminals on bottom of switch (DPDT). Used for channel
switching, FX switching on the front panels of many Marshall™ amps from the
1990s. Found in the JMP-1 preamp, 6100 Anniversary, JFX-1
Signal Processor, and early 90s Valvestate MK1 models: VS100R, VS100RH, 8010,
8020, 8040, 8080, 8100, 8200, 8240, 8280. Original Marshall™ part
number S212. For switch cap, see the K-212 or K-213.
Actuator shaft is 2.7mm square.
Part #SW-212 |
$5.95 |
|
Click on photo for
larger view |
ORIGINAL
Marshall™ , VOX, AND Blackstar™ PUSH SWITCH
DPDT Mini Short-Throw  Push Switch. Has
6 electrical terminals on bottom of switch (DPDT). Used by Marshall as
follows:
TSL100:
MID BOOST SWITCH CLEAN SW2
CLEAN/OD SWITCH SW1
OD/CRUNCH SWITCH SW3
DEEP SWITCH OD SW2
DEEP SWITCH CLEAN SW2
V.P.R.SWITCH SW3
OUTPUT MUTE SWITCH SW4
LOOP LEVEL SWITCH A SW2
LOOP LEVEL SWITCH B SW3
MB450H: Classic Channel Boost
DSL40C and DSL100H: SW2 (Channel Select), SW3 (Lead1/Lead2),
SW5 (FX-Loop ON/OFF)
Used in the Vox™
Pathfinder, V9168R, with Reverb. Vox™ part
number V3650 and V904530002. Used in most Blackstar™ Amps as SW2;
also on back PCB: SW1; SW2; and SW3.
Blackstar™ part number MCSWH02002. Also found in other brands of
amplifiers. Actuator shaft is 3.3mm square.
Part #SW-650 |
$4.95 |
|
Click on photo for
larger view |
ORIGINAL
Marshall™, Blackstar™, and Dunlop™ PUSH SWITCH
DPDT Mini Short-Throw Push Switch. Has
12 electrical terminals on bottom of switch (4PDT). Used for Tone Shift
 and Clean/Crunch on the TSL-100, TSL-122, DSL-50 and DSL-100. Also found in
the AVT100, AVT150, AVT275, TSL60, TSL601, TSL602, DSL40C. Also found in other brands of
amplifiers. Found in some Dunlop Wah pedals as the kick switch. Actuator shaft is 3.3mm square. Original Marshall™ part
number SWTP00039. Replaces the Blackstar™ MCSWH02032 Channel Select switch
in the HT1-R, the S145, and other models.
Part #SW-233 |
$6.95 |
|
Click on photo for
larger view |
ORIGINAL
ILLUMINATED Marshall™ PUSH SWITCH
4PDT Mini Short-Throw Push Switch.
Has
14 electrical terminals on bottom of switch (4PDT + LED). Contains
red LED which illuminates through the stem of the switch. Used for channel
switching on certain amp models from the JCM900 series, including the 4100,
4101, 4102, 4500, 4501 and 4502. Original Marshall™ part
number S206. Does NOT include the
clear switch cap - reuse existing cap.
Part #SW-206 |
$6.95 |
|
Click on photo for
larger view |
SQUARE SWITCH CAP - FITS SW-212
This is a black 5mm x 5mm (approx 3/16") square mini-switch cap which fits the SW-212
Marshall™ Push Switch (used primarily for channel switching). Replaces the original S213 switch cap from Marshall™ ,
which has now been discontinued. NOTE: This is
NOT the power switch cap on ValveState Amps. Also,
this switch cap does NOT fit the SW-650, SW-206, SW-256, or SW-701 switch. This square cap is found on
the Marshall™, 6100, 6101, JMP1, JCM600, JCM602, JTM310, JTM312, JTM610, JTM612,
JTM615, JTM622, 8010, AS80R, 8010, 8020, 8040, 8080, 8100, 8200, 8240, 8280, and
9004 models. For switches with actuator shaft of 2.7mm square.
Part #K-213 |
$1.50 |
|
Click on photo for
larger view |
ROUND SWITCH CAP - FITS SW-212 and 090-0012-0
This is a black 5mm (approx 3/16") diameter X 9mm long switch cap which fits the SW-212
and 090-0012-0 Push Switches. Exact replacement for most of the
round caps used on the Gallien-Krueger 400RB-II, II and IV, 700RB-II, 1001RB-II
and similar models. The diameter of this switch cap
is smaller than the original round switch cap from Marshall™ found on some of
the early ValveState models. Does NOT fit the TSL/DSL amps in the JCM2000
series. Does NOT fit the SW-650, SW-701, SW-256 or SW-206 switches. For switches with actuator shaft of 2.7mm square.
Part #K-212 |
$1.50 |
|
Click on photo for
larger view |
 Marshall™ VINTAGE STYLE IMPEDANCE SELECTOR PLUG
This male plug insert fits the speaker impedance selector socket on many vintage Marshall™ amps from 25+ years ago. Frequently lost because it was removable from the rear of the amp.
Part #P-502 |
$15.95 |
|
Click on photo for
larger view |
Marshall™ Impedance/Mode Selector switch.
Correct replacement for PCB mount impedance and high-low mode
switch found on
the back of many Marshall™ JCM900 and
JCM2000 series amplifiers. Also used
as
The impedance switch in Marshall™ 4x12 Cabinets (such as the 1960 series
cabinets). Found in other British-made amplifiers and cabinets
as well. Marshall™ part number S208.
Part #SW-4500 |
$13.95 |
|
Click on photo for
larger view |
SWITCH, STANDARD SIZE TOGGLE -
Rated at 20 Amps (125VAC) or 15 Amps (250VAC). Fits 1/2" chassis
hole. Solder terminals or 1/4" push on, single pole / single throw (SPST).
Two position - on/off. NOTE: RATED FOR AC SERVICE ONLY
AT 250V MAX - DO NOT USE AS A GUITAR AMPLIFIER STANDBY SWITCH
Part #STS-20 |
$3.95 |
|
Click on photo for
larger view |
SWITCH, STANDARD SIZE TOGGLE - Made by
Carling - rated at 15A/125VAC, 10A/250VAC. Two position (on/off), double pole (DPST). Fits
1/2" chassis hole. Solder terminals or 1/4" push-on.
Part #SW-525 |
$10.95 |
|
Click on photo for
larger view |
SWITCH, STANDARD SIZE TOGGLE - MADE BY
ELECTROSWITCH
- RATED AT 6A/125VAC, 3A/250VAC. Two position (on/off), double pole
(DPST). Fits 1/2" chassis hole. Solder terminals.
Replacement for many amps which need a 4-terminal DPST style switch with
soldered connections.
Part #SW-357 |
$8.95 |
|
Click on photo for
larger view |
SWITCH, STANDARD SIZE TOGGLE - Made by
Carling™
- rated at 15A/125VAC, 10A/250VAC. Two position (on/off), single pole (SPST). Fits
1/2" chassis hole. Solder terminals.
Part #SW-526 |
$6.50 |
|
Click on photo for
larger view |
SWITCH, STANDARD SIZE TOGGLE - RATED AT
15 Amps (125VAC) or 10 Amps (250VAC) - TWO POSITION (ON/ON).
Fits 1/2" chassis hole. Screw terminals, or remove screws for
soldered connections. Double-pole double-throw, no center
off - two positions (ON/ON).
Part #STS-15-DPDT |
$4.95 |
|
Click on photo for
larger view |
SWITCH, STANDARD SIZE TOGGLE - RATED AT
15 Amps (125VAC) or 10 Amps (250VAC) - THREE POSITION (ON/OFF/ON).
Fits 1/2" chassis hole. Screw terminals, or remove screws for
soldered connections. Double-pole double-throw, with center
off - three positions (ON/OFF/ON).
Part #STS-15-DPDT-CO |
$5.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
CARLING™ BRAND, SPDT
Found in many type of footswitches, including the earlier versions of the Dunlop Crybaby Wah pedals
(NOT the version F - see FS-435 below for Crybaby GCB-095F). Has 3 electrical terminals (single pole, double throw).
Solder lugs for wire.
Part #FS-492 |
$17.50 |
|
Click on photo for
larger view |
FOOT SWITCH,
CARLING BRAND, SPST,
LATCHING, REPLACEMENT FOR Fender™, ETC.
Carling SPST footswitch. Used in Marshall™ etc. Reverb/tremolo/channel switching pedals.
Has 2 electrical terminals (single pole, single throw).
Solder lugs for wire.
Part #FS-493 |
$9.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
SPDT,
LATCHING, FOR SWITCHING AND EFFECTS
- Marshall™ TYPE.
Has 3 electrical terminals (single pole, double throw). Solder lugs for wire.
Commonly found in Marshall™ footswitch boxes, as well as other brands.
Marshall™ part number SWP802.
Part #FS-398 |
$4.50 |
|
Click on photo for
larger view |
FOOT SWITCH,
SPDT,
PC MOUNT, FOR SWITCHING AND EFFECTS - Marshall™ TYPE, LATCHING
Electrically equivalent and physically the same body size as the FS-398, but
made for direct connection to a PC board. Found in the some Marshall™
footswitch boxes with PC board design (not for the TSL 5-way footswitch,
however). This is a latching switch. Has 3 electrical terminals (single pole, double throw).
Part #FS-398-PC |
$4.50 |
|
 |
FOOT SWITCH,
DPDT, MOMENTARY, FOR SWITCHING AND EFFECTS.
Made for switching and effects units which require a momentary connection
rather than a latching connection. Side solder lugs for wire.
Note: With momentary switches, it is necessary to check the pins
with a meter and determine the normally open and normally closed pins, comparing
to the original switch and design before wiring. Otherwise, it is possible
to wire a momentary switch "backwards" (reversed 180 degrees) and the device
will not work properly.
Part #FS-503 |
$4.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
DPDT, MOMENTARY, FOR SWITCHING AND EFFECTS.
Made for switching and effects units which require a momentary connection
rather than a latching connection. Bottom solder lugs for wire.
Note: With momentary switches, it is necessary to check the pins
with a meter and determine the normally open and normally closed pins, comparing
to the original switch and design before wiring. Otherwise, it is possible
to wire a momentary switch "backwards" (reversed 180 degrees) and the device
will not work properly.
Part #FS-503B |
$4.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
SPDT, MOMENTARY, FOR SWITCHING AND EFFECTS.
Important: This is one of two types of momentary 3-pin SPDT
footswitches using the same footprint. Click on the diagram to the
left, compare the switching with your requirements. The other switch
is the FS-602-PC, with the opposite switching logic. Customer is
responsible for testing and selecting the switch with the correct switching
logic - Studio Sound Electronics is not responsible if the wrong switch is
selected.Made for switching and effects units which require a momentary connection
rather than a latching connection.
PC terminals. Has
3 terminals.
Part #FS-502-PC |
$4.95 |
|
Click on photo for
larger view |
FOOT
SWITCH, SPDT,
MOMENTARY, FOR SWITCHING AND EFFECTS.
Important: This is one of two types of momentary 3-pin SPDT
footswitches using the same footprint. Click on the diagram to the left,
compare the switching with your requirements. The other switch is the
FS-502-PC, with the opposite switching logic. Customer is responsible
for testing and selecting the switch with the correct switching logic - Studio
Sound Electronics is not responsible if the wrong switch is selected. Made for
switching and effects units which require a momentary connection rather than a
"hard" connection (no "click"). PC terminals. Has 3 terminals, a soft-click
momentary. Used in the 5-way foot controller on the Marshall® TSL-100 amps for
the clean, crunch and lead switches.
Part #FS-602-PC |
$4.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
DPDT, MOMENTARY, FOR SWITCHING AND EFFECTS.
Made for switching and effects units which require a momentary connection
rather than a latching connection. PC terminals. Fits the
PEDL-10021 Marshall TSL 5-button foot controller (Reverb and FX positions) Note:
With momentary PC Mount switches, it is necessary to check the pins with a meter
and determine the normally open and normally closed pins, comparing to the
original switch and design before installing. Otherwise, it is possible to
install a momentary switch "backwards" (reversed 180 degrees) and the device
will not work properly.
Part #FS-503-PC |
$4.95 |
CURRENTLY UNAVAILABLE
|
Click on photo for
larger view |
FOOT SWITCH,
DPDT, LATCHING, PC MOUNT, FOR SWITCHING AND EFFECTS.
Electrically equivalent and physically the same body size as the FS-498, but made for direct connection to a PC board.
Found in the Line 6™ XPS-AB power supply for their Variax guitars. Has 6 electrical terminals (double pole, double throw).
Part #FS-498-PC
(Also see our complete line of switches) |
$4.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
ALPHA MINIATURE DPDT,
LATCHING, PC MOUNT, FOR SWITCHING AND EFFECTS.
Smaller body than the FS-498-PC, this switch is used in many stomp boxes. The
physical size of the pushbutton is the same as all of the other switches - only
the rectangular body of the switch is smaller for more compact spaces.
This is a "firm-click" switch - not a momentary. Switch is
marked "L" on the side (for "latching").
This switch is used in the Marshall AVT Stage Foot Controller PEDL-00039
used in conjunction with the AVT-150, AVT-150H, and AVT-275 models.
See this page for more information.
Part #FS-211-PC |
$6.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
ALPHA DPDT, LATCHING, SOLDER
LUGS, FOR SWITCHING AND EFFECTS.
This switch is the same as the FS-211-PC, except it has solder lugs for wire
attachment. Made for effects boxes that do not have a PC board under
the footswitch. The physical size of the pushbutton is the same as all of
the other switches - only the rectangular body of the switch is smaller for more
compact spaces. This is a "firm-click" switch - not a momentary.
Switch is marked "L" on the side (for "latching").
Part #FS-211 |
$6.95 |
|
Click on photo for
larger view |
PREMIUM FOOT SWITCH,
TAIWAY 3PDT, LATCHING, SOLDER
LUGS, FOR SWITCHING AND EFFECTS. LOW PROFILE
Solder lugs for wire attachment, low profile, small body size for compact
spaces. Longer threaded bushing than the FS-311. Softer "click"
during switching than the FS-311 switch. Manufactured by Taiway. Made for effects boxes that do not have a PC board under
the footswitch. 3PDT - perfect for true bypass plus an additional contact
for LED switching. Body size is 17mm L x 13.5mm W x 13mm H.
Data sheet here. This is a
latching switch - not a momentary.
Part #FS-311T |
$8.95
Only 1 left in stock! |
|
Click on photo for
larger view |
FOOT SWITCH,
ALPHA 3PDT, LATCHING, SOLDER
LUGS, FOR SWITCHING AND EFFECTS. LOW PROFILE
Solder lugs for wire attachment, low profile, small body size for compact
spaces. Made for effects boxes that do not have a PC board under
the footswitch. 3PDT - perfect for true bypass plus an additional contact
for LED switching. Body size is 17mm L x 13.5mm W x 13mm H. This is a "firm-click" switch - not a momentary.
Switch is marked "L" on the side (for "latching").
Part #FS-311 |
$6.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
ALPHA DPDT, MOMENTARY, PC MOUNT, FOR SWITCHING AND EFFECTS.
This switch is the same as the FS-211-PC, except it is a slightly softer-click
momentary (no firm
click) for those pedals which require a momentary switch. Switch is
marked "M" on the side for momentary. Momentary switches do not
latch - once the switch is released, the contacts revert to their normal state. Pins for PC
board mounting. The physical size of the pushbutton is the same as all of
the other switches - only the rectangular body of the switch is smaller for more
compact spaces. This switch is used in the Marshall AVT Stage Foot
Controller PEDL-00039 used in conjunction with the AVT-150, AVT-150H, and
AVT-275 models.
See this page for more information.
Note: With momentary PC Mount switches, it
is necessary to check the pins with a meter and determine the normally open and
normally closed pins, comparing to the original switch and design before
installing. Otherwise, it is possible to install a momentary switch
"backwards" (reversed 180 degrees) and the device will not work properly.
Part #FS-211-PC-M |
$6.95 |
|
Click on photo for
larger view |
FOOT SWITCH,
ALPHA DPDT, MOMENTARY, SOLDER
LUGS, FOR SWITCHING AND EFFECTS.
This switch is the same as the FS-211-PC-M, except it has solder lugs for wire
attachment. This switch is a slightly softer-click momentary (no firm click) for those pedals
which require a momentary switch. Switch is marked "M" on the side for
momentary. Momentary switches do not latch - once the switch is
released, the contacts revert to their normal state. Made for effects boxes that do not have a PC board
under the footswitch. The physical size of the pushbutton is the same as
all of the other switches - only the rectangular body of the switch is smaller
for more compact spaces. Note: With momentary switches, it
is necessary to check the pins with a meter and determine the normally open and
normally closed pins, comparing to the original switch and design before wiring.
Otherwise, it is possible to install a momentary switch "backwards" (reversed
180 degrees) and the device will not work properly.
Part #FS-211-M |
$6.95 |
|
Strat™, Stratocaster™, Esquire™, Telecaster™, Tele™, Jazzmaster™, Jaguar™, Mustang™, P.Bass™, J.Bass™ and Fender™ are registered trademarks of Fender™ Musical Instruments. The replacement necks and bodies are for a Fender™ or Squier™ by Fender™ guitar or bass. The distinctive headstock designs and the distinctive body designs of the Stratocaster™, Telecaster™, J.Bass™, P.Bass™ and Tele™ Bass are registered trademarks of Fender™ Musical Instruments Co.
Peavey™ is a registered trademark of Peavey™ Electronics Corporation.
Marshall™ is a registered trademark of Marshall™ Amplification Plc.
Mesa Boogie™ is a registered trademark of MESA/Boogie™ Ltd.
AmpRepairParts.com and Studio Sound Electronics are not affiliated with these companies.
All company names, logos and product names mentioned on these pages are trademarks of their respective owners.
Copyright ©2024 Studio Sound Electronics -
All Rights Reserved
Not responsible for web site errors or omissions.
WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.
For more information go to www.P65Warnings.ca.gov
|
