(Disregard color code in the picture. The actual resistor is
brown-red-red-gold) |
RESISTOR,
FLAMEPROOF, 820 OHM, 3 WATT. Found in some versions of the
Fender Blues and Hot Rod series amps as part of the power feed circuit to the
footswitch.
Part #820FP3 |
$0.45 each
In stock |
|
|
(Disregard color code in the picture. The actual resistor is
brown-red-red-gold) |
RESISTOR,
FLAMEPROOF, 1.2K OHM, 3 WATT. Found in some versions of the
Fender Blues and Hot Rod series amps as part of the power feed circuit to the
footswitch.
Part #1200FP3 |
$0.45 each
In stock |
|
Click on photo for
larger view |
CAPACITOR, CERAMIC DISC, RADIAL. Replacement for the ceramic disc
120pF "Bright Switch" capacitor in larger Fender Blackface and Silverface amps.
Capacitor is soldered to terminals on the Bright Switch on both channes.
Turning on the Bright Switch at lower volume allows more higher frequency tones
through the amp circuitry, producing a brighter sound.
Part #C-CD-120PF |
$0.75
In stock |
|
Click on photo for
larger view |
WASHER, FOR BRITISH STYLE (CLIFF) JACKS.
This washer goes behind the faceplate on British style plastic nut and
chrome nut jacks to provide proper spacing. Jacks come with the
washers included, but the washers are easily lost. Without the washers,
the jacks will not fit properly.
Part #W-583 |
$0.24
In stock |
|
Click on photo for
larger view |
ROCKER SWITCH,
POWER OR STANDBY,
WHITE Fits in rectangular cutout of 0.86" wide x 1.15" tall
(22mm x 29mm). Fits most any amp which uses a large rocker switch
(Marshall, etc). 4 terminals push-on terminals on back of switch (switches
both the hot and neutral sides.) May be used for either Power or Standby.
Note - not illuminated.
This switch is priced to sell!
Part #SW-490CW |
$2.50
In stock |
|
Click on photo for
larger view |
 JACK,
1/4", CHROME NUT, CLOSED CIRCUIT, PC MOUNT, EXTENDED PCB PINS, TIP-SLEEVE,
4 PINS.
Usually found in amplifiers or pedals built in China or Taiwan.
Frequently used in Kustom™ products. 4 pins, PC mount, with
chrome nut and washer. Note "extended" pins as shown in photo.
Part #J-580SL |
$3.95
In stock |
|
15 FEET
Click on photo for
larger view |
Revisit™
INSTRUMENT CABLE 15 FEET
Revisit 1/4" musical instrument cables
provide the reliable link that lets you concentrate on a great performance. Also
great for unbalanced line level interconnection, too.
15 feet long, 1/4" straight connectors.
22 AWG oxygen-free copper stranded center conductor for maximum signal transfer
Coaxial construction and copper 95% braided
shield reduce noise
Premium jacket materials provide ease of
handling and long service life
Gold plated straight 1/4" connectors for
long-term conductivity
Part #GCB-15 |
$12.99
In stock |
|
20 FEETClick on photo for
larger view |
Revisit™
INSTRUMENT CABLE 20 FEET
Revisit 1/4" musical instrument cables
provide the reliable link that lets you concentrate on a great performance. Also
great for unbalanced line level interconnection, too.
20 feet long, 1/4" straight connectors.
22 AWG oxygen-free copper stranded center conductor for maximum signal transfer
Coaxial construction and copper 95% braided
shield reduce noise
Premium jacket materials provide ease of
handling and long service life
Gold plated straight 1/4" connectors for
long-term conductivity
Part #GCB-20 |
$13.99 Only one is left in
stock! |
|
20 FEETClick on photo for
larger view |
Revisit™
INSTRUMENT CABLE RIGHT-ANGLE 20 FEET
Revisit 1/4" musical instrument cables
provide the reliable link that lets you concentrate on a great performance. Also
great for unbalanced line level interconnection, too.
20 feet long, 1/4" straight and right-angle connectors.
- 22 AWG oxygen-free copper stranded center
conductor for maximum signal transfer
- Made to handle all the abuse musicians can
dish out
- Coaxial construction and copper 95%
braided shield reduce noise
- Premium jacket materials provide ease of
handling and long service life
- Gold plated straight/right-angle 1/4"
connectors for long-term conductivity
- Durable metal shell for extra shielding
and long service life
Part #RGCB-20 |
$14.99 |
 |
|
REVISIT™ CHANNEL SELECT TOGGLE SWITCH
FOR Peavey™ (SHORT BAT-HANDLE, ORIGINAL)
2P3TSP Toggle Switch used for the front panel
channel select switch on the Triple XXX and Triple XXX II amp series.
Used as the resonance switch in the Ultra 112, Ultra 212, Ultra 410 combos and
Ultra Plus head. Replaces original Peavey™ part number
71322368 or 31322368. See also the SW-236L, below.
Part #SW-236A |
$4.95
In stock |
|
|
REVISIT™ CHANNEL SELECT TOGGLE SWITCH
FOR Peavey™ (LONG BAT-HANDLE, EASIER TO SWITCH)
2P3TSP Toggle Switch used for the front panel
channel select switch on the Triple XXX and Triple XXX II amp series.
Used as the resonance switch in the Ultra 112, Ultra 212, Ultra 410 combos and
Ultra Plus head. Replaces original Peavey™ part number
71322368 or 31322368. (This version has a longer handle than the
original, for easier switching.)
Part #SW-236L |
$4.95
In stock |
|
Click on photo for
larger view |
SWITCH, STANDARD SIZE HEAVY-DUTY
TOGGLE -
Rated at 20 Amps (125VAC) or 10 Amps (250VAC). Fits 1/2" chassis
hole. Screw terminals. Single pole / single throw (SPST).
Two position - on/off.
Part #STS-8 |
$2.95
In stock |
|
Click on photo for
larger view |
JACK,
1/4", CHROME NUT, CLOSED CIRCUIT, PC MOUNT, EXTENDED PCB PINS, TIP-RING-SLEEVE,
6 PINS. Usually found in amplifiers or pedals built in China or Taiwan.
Frequently used in Kustom® products. 6 pins, PC mount, with chrome nut and
washer. Note "extended" pins as shown in photo. For data sheet
showing dimensions,
click here
Part #J-581SL |
$3.95
In stock
|
|
Click on photo for
larger view |
JACK,
1/4", CHROME NUT, CLOSED CIRCUIT, PC MOUNT, EXTENDED PCB PINS, TIP-SLEEVE,
4 PINS.
Usually found in amplifiers or pedals built in China or Taiwan.
Frequently used in Kustom™ products. 4 pins, PC mount, with
chrome nut and washer. Note "extended" pins as shown in photo.
Part #J-580SL |
$3.95
In stock |
|
 |
Adapter, RCA PLUG TO RCA
PLUG
Allows connection of standard RCA cable to each
other.
Part
#P-282 |
$0.89
In stock
|
|
Click on photo for
larger view |
JACK, 1/4", PC MOUNT, STEREO,
3 PINS, SWITCHED, INSULATED. Used in many Peavey™
and SWR™ models. Switched tip contact.
Original Peavey™ part number 71466165. Original SWR™ part number
0066442000. Nut and washer are included. 3 pins.
Part #J-526A |
$7.75
In stock |
|
Click on photo for
larger view |
PHENOLIC TUBE SOCKET FOR OCTAL TUBES. Fits 6L6, EL34, 6V6 output tubes, and 5U4, 5Y3, and GZ34 rectifier tubes. For 1-1/8" hole.
Bottom mounting (mounted from the inside of the chassis), mounting holes spaced 1 1/2" apart.
Part #TS-8-250 |
$5.15
In stock |
|
Click on photo for
larger view
|
Black Oxide Stainless Steel Pan
Head 10-32 x 1" Speaker Mounting Screws, Rack Mount Screws
Set of 4 screws. Used to mount speakers, back panels, etc in a
variety of amplifiers. 10-32 thread, 1" long with pan head.
May also be used as rack-mount screws. Stainless steel, will not rust.
Part #SC-202A |
$1.79
(for a set of 4 screws)
In stock |
|
Click on photo for
larger view |
CAPACITOR, electrolytic 2200uF @ 63V with radial snap-in leads.
Made by Chemi-Con. Dimensions: 22mm x
35mm.
Part #RAD-2200-63 |
$6.95
In stock |
|
Click on photo for
larger view |
 Revisit™ BiasEasy™
800
The Bias Easy™ 800 measures the
current in the power tubes of your amp. Includes two 8-pin probes with gold
plated pins and socket, power adapter and
operating instructions. Fully assembled and ready to use. For 8-pin
power tubes such as 6L6, 6V6, 5881, 6550, EL34, KT88, KT66, KT100, etc.
Not for 7591 tubes.
The Bias Easy™ 800 allows you to monitor the bias
setting safely and easily. While adjusting the bias control pot of your amp, the
Bias Easy™ shows the actual current flowing through each of two power tubes.
A switch on the meter allows you to go back and forth between the two tubes.
This lets you set and evaluate the full reasonable biasing range your amp and
tubes offer so that you may find the perfect setting. Complete
instructions are
included.
The bias setting has a dramatic impact on the
amp's tone, response, break-up and dynamic character.
Part #RBE-800 |
$89.95
In stock |
|
Click on photo for
larger view |
Revisit™ BiasEasy™
1200 Quad Tube Amp Bias Tester
The Bias Easy™ 1200 measures the
current in the power tubes of your amp. Designed for amplifiers with
4 power tubes, such as 100 watt Marshalls and the Fender Twin Reverb.
(May also be used on amps with only 2 power tubes). Includes four 8-pin probes with
gold
plated pins and socket, power adapter and
operating instructions. Fully assembled and ready to use. For 8-pin
power tubes such as 6L6, 6V6, 5881, 6550, EL34, KT88, KT66, KT100, etc.
Not for 7591 tubes.
The Bias Easy™ 1200 allows you to monitor the bias
setting safely and easily. While adjusting the bias control pot of your amp, the
Bias Easy™ 1200 shows the actual current flowing through each of the four power tubes.
A rotary switch on the meter allows you to check each tube for current flow. This lets you set and evaluate the full reasonable biasing range your amp and
tubes offer so that you may find the perfect setting. Complete
instructions are
included.
The bias setting has a dramatic impact on the
amp's tone, response, break-up and dynamic character.
Part #RBE-1200 |
$124.95
In stock |
|
Click on photo for
larger view |
POTENTIOMETER WITH SWITCH,
POTENTIOMETER WITH SWITCH,
Used as the replacement for
Fender part number 012561. Distortion control in the
Fender Super Twin and the Fender PS-300 (sometimes referred to as the 300-PS).
Has flattened D-shaft and rotary switch control. The pot is a B100K.
Part #012561 |
$8.95
In stock |
|
Click on photo for
larger view |
BALL
HEAD MESH GRILLE AND WINDSCREEN FOR SHURE™
Fits
the majority of "58-style" microphones, including the Shure™
SM58, SM48, Beta 58A, SM58LC, SV100, RK143G, PGX2, Pyle™
PDMIC58, and virtually any other ball-style handheld microphone.
Save with this excellent
Revisit™
reproduction at a fraction of the cost of the
replacement Shure™
grille.
Part #MG-58 |
$9.95
In stock |
|
|
Click on photo for
larger view |
 REVISIT
POLARITY REVERSING ADAPTER CABLE
Fixes the frustrating problem of having a power supply designed for "center
pin positive" and a pedal which requires "center pin negative". Or
vice-versa! This ingenious adapter cable reverses the center pin
with the outside ring, allowing you to successfully use a "backwards" pedal with
your pedal power supply. The connectors are the popular 2.1mm x 5.5mm
size. 5 inches long.
Part #PRC-129 |
$2.29
In stock |
|
Click on photo for
larger view |
 ROCKER SWITCH,
HI POWER/LOW POWER +
STANDBY,
ORIGINAL Marshall™. FOUND IN Marshall™
SC20C, SC20H, 2525H, 2525C, DSL100HR, DSL40CR. Has 6 electrical terminals on back of switch. MATTE
FINISH (NOT SHINY)
1/4" push-on terminals. Now in stock and ready to rock! Rated 16A. 15/16" x 1 1/16" x 1" deep.
Only used in the SC20C, SC20H, 2525H, 2525C, DSL100HR and DSL40CR.
Part #SW-496 |
$9.95
In stock
|
|
Click on photo for
larger view |
 KNOB, Music Man™, SET-SCREW
Music Man™ style amp knob, skirted with 1-10 numbering. Traditional
"Witches Hat" design. For vintage Music Man™ amps. With set-screw,
for 1/4" smooth shaft pots.
These are different than the Fender skirted knobs. A lot of people
put Fender knobs on Music Man amps, but they won't exactly match the other
knobs. This is the exact replacement for Music Man.
Part #K-155 |
$5.50
In stock |
|
W-TAPER
Click on photo for
larger view |
POT,
W-TAPER,
PC MOUNT, 16mm DIAMETER BODY, 7mm DIAMETER THREADED BUSHING, KNURLED SHAFT
Found in many Hartke amps as well as
other amps and pedals.
Typically used as an EQ pot. W-Taper pots are reverse audio taper
up to the midpoint, but regular audio taper past the midpoint.
Available with or without "center click detent" which marks the midpoint with a
slight click you can feel as you turn the pot. Diameter of the body of the pot is slightly smaller than a dime.
Available in the two most common values of W20K and W100K. Both
values are available with or without the center click detent.
Click on photo for more detail.
INCLUDES NUT & WASHER
(For spare or replacement nut,
order the PNW-16 nut and washer set found here).
Part #P-W16-XX |
$3.95
In stock |
|
Click on photo for
larger view |
Marshall™ VINTAGE RED INDICATOR LIGHT
- 120 VOLT.
Indicator light, round. 120 Volts. 3/8" mounting hole. Used
in vintage Marshall™ designs such as the JTM-45 and JTM-100 from the early
1960s. Also is a good replacement for the obsolete Peavey red pilot
lights on vintage Peavey amps. 120 volt lamp -
designed to run on the switched line voltage (North America only).
Mounting nut is included.
Part #MPL-6010R
|
$12.95
In stock |
|
Click on photo for
larger view |
KNOB, Fender™ style "mini witch's hat", skirted
1-10
Fender™ style amp knob, black, chrome center disc, skirted, with 1-10 numbering. Knob is a
slip-on, designed to fit a knurled shaft pot. Base
is 7/8"
diameter. Fits
any split knurled shaft pot, such as those found on certain models of the
Sidekick series, the Rumble series etc. Also will fit other
amp brands with knurled shaft pots.
Part #K-338 |
$1.95
In stock |
|
Click on photo for
larger view |
SWITCH, STANDARD SIZE TOGGLE - MADE BY
ELECTROSWITCH
- RATED AT 6A/125VAC, 3A/250VAC. Two position (on/off), double pole
(DPST). Fits 1/2" chassis hole. Solder terminals.
Replacement for many amps which need a 4-terminal DPST style switch with
soldered connections.
Part #SW-357 |
$8.95
In stock |
|
Click on photo for
larger view
|
Fender™
RCA VIBRATO SHORTING PLUG
by
Revisit™ - GOLD-PLATED. Did you know that on
vintage Fender™ amps (Blackface, Silverface), the reverb
will work without a footswitch plugged in, but the vibrato will not?
This handy-dandy little RCA shorting plug will fix that problem, if you do
not own or prefer not to use a footswitch on your vintage 60s or 70s Fender™
amp. This version is made of gold-plated brass for a low
resistance connection and highest immunity to oxidation. Just plug this little RCA plug gadget into the vibrato
footswitch jack on the back panel, and your vibrato will come alive.
Turn the intensity knob to zero to cut out the vibrato when this plug is
inserted.
Part #FSP-200
|
$2.50
In stock
|
|
Click on photo for
larger view
|
Black Oxide Stainless Steel Pan
Head 4-40 x 5/16" Screws and Nuts, Set of 4
Set of 4 small black screws with matching nuts. Stainless steel
with black oxide finish. Used in a variety of applications on both guitars
and amplifiers.
Part #SCBN-440 |
$1.69
(for a set of 4 screws with nuts)
In stock |
|
Click on photo for
larger view
|
REVISIT™
3-POSITION SLIDE SWITCH FOR Peavey™
2P3T Slide Switch used for Impedance,
Power Level, or Damping on the back panel of several Peavey™
amps. Found in the
Peavey Windsor Studio, 6505 112 Combo, Joe Satriani JSX, ValveKing 212 Combo, ValveKing Head, 5150-II,
Supreme 160/Transtube Supreme and XXL models. Replaces original Peavey™ part number
71322328 or 31322328. Mounting hardware included
Part #SW-313 |
$9.95
In stock |
|
Click on photo for
larger view |
ROCKER
SWITCH, MESA/BOOGIE, BASS 400+
1/4" push-on terminals.
Made for 1.07" H x 0.88" W mounting hole. Rated 20A @ 125VAC.
15A @ 250VAC. Used for Power or Standby on the Bass 400+. Original
Mesa/Boogie
part number 600505.
Part #SW-547 |
$7.99
In stock |
|
Click on photo for
larger view |
FUSE HOLDER, HIGH QUALITY, USED ON VINTAGE Marshall™ AMPS
Marshall™ style fuse holder. Threaded mount for chassis hole diameters between 5/8" and 11/16". Flush design, fuse cap removed with screwdriver. Used on Marshalls from the 60's, 70's
and 80`s, including the
JCM 800. This low profile fuse holder will
make an excellent replacement for your original amplifier that is in need of
repair or restoration. Easy to install and ready to serve you for years! Fits
5mm X 20mm (GDC, GMA) size fuses.
Part #FH-421 |
$6.50
In stock |
|
|
KNOB,
Revisit™ Marshall™, PUSH ON D-SHAFT (Read applicable models!)
Standard Revisit™
Marshall™
style control knob, push-on type, for D-Shaft pots used in
the following Marshall™
amp models: DSL-201 combo, DSL-401 combo,
DSL-40C combo, TSL-122 combo, TSL-601 combo, TSL-602 combo, JVM205H head,
JVM210H head, JVM410H head, VS15 combo, VS30R combo, VS65R combo, VS100R
combo, VS100RH head, VS102R combo, VS230 combo, VS265 combo, AVT20 combo, AVT50
combo, AVT50H head, AVT100 combo, AVT150 combo, AVT150H head, AVT275 combo, AS100D combo, MA50C
Combo, MA100C Combo, MG10, MG15, MG15FX, MG30FX, MG50FX, MG100FX, MG100HFX,
MG102FX.
For the similar knob used on DSL and TSL JCM2000 series heads, MA series heads,
and JVM series combos see the MKDS knob elsewhere on this page.
The R-MKDS-C Knob is constructed so that the pointer on the front of the knob is
180 degrees away from the flat spot in the shaft hole on the back side of the
knob.
Part #R-MKDS-C |
$2.99
(Single Knob)
In stock |
|
Click on photo for
larger view |
JACK, 1/4", PC MOUNT, STEREO,
6 PINS, SWITCHED, INSULATED.
Original Peavey part number 31466165 and 71466165. Found in some versions
of the 5150, 6505, 5150-II and 6505+, as well as the pre-EQ jack on the KB60.
Used as the input jack on the older version of the Basic 112. Nut and washer included.
Part #J-625 |
$8.95
In stock |
|
Click on photo for
larger view |
 REPLACEMENT
HOUSING 3/8" SCREWS FOR MXR™ PEDALS (VINTAGE VERSION)
Set of 4 housing screws for MXR™, Way Huge and
other pedals which use 6-32 x 3/8" screws, including pedals which use Bud or
Hammond style enclosures.Early MXR™
pedals (1972-1987) require a 3/8" screw to attach the bottom cover.
The D-ECB-590 screw is too long for the vintage MXR pedals.
Part #D-ECB-589 |
$0.59
(for a set of 4 screws)
In stock |
|
Click on photo for
larger view |
Revisit™ BiasEasy™
200
Cathode Current Measuring Probe
For 8-pin power tubes such as 6L6, 6V6, 5881, 6550,
EL34, KT88, KT66, KT100, etc.
Requires separate digital volt-ohmmeter capable of reading current.
This device reads cathode current.
Note: This
adapter will NOT test 7591 tubes. Quality throughout, with a ceramic
socket, gold-plated socket pins and gold-plated banana plugs to ensure solid connections and
accurate readings.Not a kit - this
device is fully assembled and ready to use! Complete with detailed
instructions.
Used with a basic multimeter (Get Yours Here).
Part #RBE-200 |
$29.95
In stock |
|
Click on photo for
larger view |
IEC
POWER CONNECTOR, PEAVEY™,
NON-FUSED, PCB MOUNT
Used in the Peavey™ 6505+ 112 Combo (not 6505
or 6505+ heads), ValveKing series, including
the ValveKing 112 and 212 combos, and the ValveKing Head amplifiers.
Also used in the XR684 and XR1600F Powered Mixers, and the Peavey™
S14 and S24 mixing consoles.
Original Peavey™ part number 70901428 and
30901428.
Datasheet here.
Part #30901428 |
$5.95
In stock |
|
Click on photo for
larger view |
10 OHM, 5A NTC (Negative
Temperature Coefficient) type Thermistor.
Fender part number 028503. Used in many Fender amp models
since the 1990s. Also used in some Mesa Boogie amps. It is installed in series in a circuit
between the transformer and incoming AC power. This thermistor is rated for
5A maximum current, and is 19mm in diameter. By limiting
inrush current, it protects the transformer and other components in the power
supply at turn-on. This thermistor should only be used on amps which
have a 5 amp fuse or less.
Download data sheet here.
Part #CL-60 |
$3.99
In stock |
|
Click on photo for
larger view |
MULTI-TURN
TRIM POT, 50K Ohms, TOP ADJUSTMENT SCREW. This 3/8" X 3/8" X 1/8" pot may be used to modify some amplifiers
and install a bias adjust control. 50k Ohms, 0.5 watts, 25
turns. This is the pot most often used to add adjustable bias to the Fender™
Blues Junior.
Instructions for the Blues Junior Bias Mod are
found here.
Part #3296W-B50K |
$2.79
In stock |
|
New Style:
Old Style:
Click on photo for
larger view |
POT - Fender™ BIAS POT 25K LINEAR, SCREW
New style Fender™ 25K linear bias potentiometer. Used in
the reissue 59 Bassman, reissue Hot Rod Deluxe/Deville, reissue Blues
Deluxe/Deville. Fender™ part # 0027873000. This
pot is a drop-in replacement for the original discontinued "blue" bias pot.
Part #FBP-AP25KL |
$2.95
In stock |
|
|
|
 Fender™
TILT-BACK LEG SCREWS AND CAPTIVE NUTS
Pack of 2 stainless steel tilt-back leg screws,
1-1/2 inches long, along with hex nuts with special nylon inserts. Used on tilt-back legs of larger Fender™ combo
amps and speaker cabinets. Replaces Fender™ part numbers 021998 and
022277.
Part #SCW-403T-2 |
$1.79
(for a pack of 2 screws and
2 nuts)
In stock |
|
WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm.