|
Audio Driver Diaphragms |
|
Photo |
Description |
Price |
Purchase |
Click on photo for
larger view |
Genuine Eminence Diaphragm
16 Ohms
REPLACEMENT 8-OHM AUDIO DIAPHRAGM. TITANIUM COMPRESSION DRIVER, 2" DIAMETER VOICE COIL, 80 WATTS, 16 OHM IMPEDANCE, 1,200-20,000HZ. USED IN MANY PROFESSIONAL HORN DRIVERS, INCLUDING YAMAHA AND CARVIN.
Part #
PSD2002-16DIA |
$39.95 |
Stock no:
PSD2002-16DIA
16 Ohms
$39.95
|
For crossover capacitors, see our crossover capacitor web page
|
|
Speaker
Accessories & Supplies |
Click on photo for
larger view |
L-PAD FACE PLATE AND KNOB, for 3/8" diameter threaded bushing found on most L-Pad Level
controls. Face plate AND knob only! L-Pad ordered separately.
Fits many bass
cabinets including the SWR Goliath, Marcus Miller Golight 410, Workingman
8x10, Working Pro 2x10, Ampeg PN-210HLF, PN-410HLF, SVT-410HLF, SVT-610HLF,
SVT-810SPC, BXT210M,
BXT410HL4, PR-1528HE, PN-115HLF, PR-810H, PB-250, the Kustom G410H, the
Engl B115 as well as many others.
This is the face plate and knob only - L-PAD itself ordered separately.
Raised lettering in charcoal gray instead of white. 3 1/8 inches in
diameter, 7/8 inch depth into cabinet. Requires 2 inch diameter hole
for mounting. Screws not included.
Part #LFP-380 |
$4.50 |
|
8 Ohms
Click on photo for
larger view |
L-PAD, 8 Ohms, 3/8" threaded bushing (3/8" long), with plate, knob and hardware.
May also be used with the LFP-380 face plate and knob. 8 ohms
- for use with 8 ohm speakers, horn drivers or tweeters.
L-pads adjust the relative volume of drivers connected to them by placing added
resistance in series and parallel, keeping impedance a constant 8 ohm load. This
L-pad is rated at 100 watts RMS, is designed to be used with 8 ohm loads,
features a 3/8" shaft length, and comes with mounting hardware. This
style of L-Pad is found on many popular bass cabinets to control the
horn/tweeter level. 2.5 inches in diameter, 1 inch thick.
Included face plate is 2 1/8" x 2 1/8".
Part #LPD-262 |
$19.95 |
|
16 Ohms
Click on photo for
larger view |
L-PAD, 16 Ohms, 3/8" threaded bushing (3/8" long), with plate, knob and hardware.
May also be used with the LFP-380 face plate and knob. 16 ohms - for
use with 8 ohm speakers, horn drivers or tweeters.
L-pads adjust the relative volume of drivers connected to them by placing added
resistance in series and parallel, keeping impedance a constant 8 ohm load. This
L-pad is rated at 100 watts RMS, is designed to be used with 16 ohm loads,
features a 3/8" shaft length, and comes with mounting hardware. This
style of L-Pad is found on many popular bass cabinets to control the
horn/tweeter level. 2.5 inches in diameter, 1 inch thick.
Included face plate is 2 1/8" x 2 1/8".
Part #LPD-261 |
$19.95 |
|
|
|
Upgrade your PA
Cabinets to Neutrik™ speakON™! |
|
|
|
Click on photo for
larger view |
JACK PLATE, BLACK METAL
For two Neutrik™
NL4MP speakON™
connectors
Steel dish pre-punched. Constructed of heavy-duty 1.2
mm/.047" steel. Black oxide finish. Jacks not included - order
separately. Dimensions: 4" x 4 3/8".
See full dimensions here
Part #JP-028 |
$4.95 |
|
|
Click on photo for
larger view |
JACK PLATE, BLACK METAL
For two Switchcraft #11 jacks and two Neutrik™ NL4MP speakON™ connectors.
This allows you to connect to the cabinet via speakON™ connectors or 1/4" plugs.
Constructed of heavy-duty 1.2 mm/.047" steel. Black oxide finish. Jack not
included - order separately. Dimensions: 4" x 4 3/8".
See full dimensions here
Part #JP-322 |
$4.95 |
|
Click on photo for
larger view |
JACK, SPEAKON, CHASSIS-MOUNT - MADE FOR
WIRE ATTACHMENT (3/16" PUSH ON CONNECTORS OR SOLDER TABS).
Made by Neutrik. 4 pins (1+, 1-, 2+, 2-) Used in a variety of brands, including
Peavey™.
Part #J-NL4MP |
$4.95 |
 |
Click on photo for
larger view |
Revisit™
JACK PLATE COMPLETE WITH
SWITCHCRAFT #11 JACK.
Switchcraft #11 jack preinstalled with lock washer and trim washer. Outside diameter 2 inches (51mm). Minor assembly required. Designed to fit flush against a 1 1/8" (29mm) cabinet hole. Easy to install - drill 1 1/8" hole in cabinet, attach speaker wiring to jack and speaker, attach plate to cabinet.
Part #JPC-180 |
$4.95
|
|
Click on photo for
larger view |
 Fender™
STYLE SPEAKER CABINET JACK PLATE ASSEMBLY WITH JACK
As used on blackface and silverface speaker cabinet (Bassman, Bandmaster,
Showman, etc). Complete with long-bushing Switchcraft jack
with nut and trim washer, and two
nickel jack ferrules for the inside and outside of
the cabinet back. For wood panels between 3/8 inch and 1/2 inch thick.
Keep your vintage Fender™ cabinet looking original!
Part #JPC-577 |
$16.95 |
|
Click on photo for
larger view |
CRATE™ JACK PLATE, BLACK PLASTIC, DUAL 1/4" JACK, SIZE 3 3/8" x 3 3/8". Designed to fit in a 3" round hole, easily cut in a cabinet with a 3" hole saw. Jack mounting hole is 3/8", for most Switchcraft
and British type jacks. Easy to install, economical.
Found in many Crate™ speaker cabinets,
including the Crate™
G412SL, GX412XSA, GX412XR, GT112SL, BX-115E and other cabinets. Priced per jack plate.
Jacks not included - order separately below.
Part #JP-225 |
$2.79
|
|
Click on photo for
larger view |
JACK PLATE, BLACK METAL, SINGLE 1/4" JACK, 2" OUTSIDE DIAMETER. Similar in style to vintage Fender™ jack plates. Works well with the Switchcraft J-11 1/4" jacks
that we carry. Hole is 3/8", for most Switchcraft type jacks. Easy to install, economical.
Includes 3 black oxide coarse-thread mounting screws, #6x3/4".
Jack not included - order separately. For size specifications, click here.
Part #JP-180 |
$1.89
|
|
Click on photo for
larger view |
Revisit™ 18 GAUGE COPPER BONDED RED/BLACK ZIP CORD
Make low-cost, efficient speaker cables with this color-coded 18 gauge dual zip
cord. Red and black for easy polarity identification. Resistance
is 0.0097 ohms/ft.
Automotive grade "GPT" PVC insulation, oil and gas resistant, rated
for -20 deg F to +160 deg F. Also perfect
for bias testers, radio, home theatre, automotive, stereo, robotics, and model
train applications. Priced per foot, sold in lengths from 1 foot to
40 feet.
Part #RBZ-18 |
$0.32
(priced per foot) |
|
>
Click on photo for
larger view |
Revisit™
F1 to F2 Faston Push-on Terminal adapters
Used to change the size of speaker terminals from .187" (3/16") to .250"
(1/4"). Also used to change the size of some PC board connectors.
Female .187" to male .250"
Part #F1F2 |
$1.89
(Set of 2 adapters) |
|
Click on photo for
larger view |
Revisit™
F2 to F1 Faston Push-on Terminal Adapters
Used to change the size of speaker terminals from .250" (1/4") to .187"
(3/16"). Also used to change the size of some PC board connectors.
Female .250" to male .187"
Part #F2F1 |
$1.89
(Set of 2 Adapters) |
|
Click on photo for
larger view |
 Revisit™ Fender™
STYLE "SPIDER" DISTRIBUTION CONNECTOR FOR BLACKFACE SPIDER SPEAKER HARNESSES
Replacement vintage style Spider distribution board, used to tie together
speaker wires in some vintage blackface Fender™ amps, particularly the vintage
blackface Super Reverb. Also found in some blackface 2-speaker amps,
including the
Pro Reverb, Twin Reverb, Vibrolux Reverb, and Vibroverb amplifiers from the 60s.
Part #FSJ-428 |
$6.50 |
|
Click on photo for
larger view |
Revisit™
SPEAKER HARNESS
Replacement right-angle plug with 34" cable and 3/16" fast-on connectors.
Used to replace speaker cable in most combo amplifiers where the speakers are
connected to the amplifier chassis via a 1/4" jack and plug. 18ga black zip cord,
right-angle plug and fast-on connectors for attachment to one
speaker.
Part #SCH-280 - NOTE: OUT OF STOCK! NONE AVAILABLE AT THIS TIME. |
$6.99 |
|
|
Click on photo for
larger view
|
SPEAKER JUMPER CABLE
polyvinyl
insulated silver plated copper speaker wire, 18 gauge, twisted
pair, black and white. Terminated at each end in standard
3/16" speaker fast-on connectors. Great for connecting
speakers in parallel in 2x12 or 4x12 cabinets. 24 inches (61
cm) long. Made in USA.
Part #SJ-150
|
$5.99
|
|
|
 |
BUILD YOUR OWN Speaker Harness for Combo Amps: Choose the SJ-150
cable (above) along with the P-287 Plug (below). Cut off the
cable's fast-on connectors on ONE end of the cable. Strip both
conductors of cable back about 1/4" on that end. Solder that end to
the P-287 plug (black to the sleeve, white to the tip.). This
will give you a 24 inch speaker harness. Note:
Cable-building experience strongly recommended. Soldering
equipment needed. |
Total cost for materials will be $5.99 + $3.95 = $9.94. |
 |
Click on photo for
larger view |
PLUG, 1/4", MONO, RIGHT ANGLE,
SOLDER TERMINALS, STRAIN RELIEF
Similar to the Switchcraft 226 right-angle plug. Nickel plated copper alloy.
2-conductor right-angle phone plug, solder terminals.
Part #P-287 |
$3.95 |
|
Click on photo for
larger view |
PLUG, 1/4", NEUTRIK/REAN MONO,
SOLDER TERMINALS, STRAIN RELIEF, EXTRA LARGE BODY
Commercial wide-body 1/4" mono phone plugs designed
specifically for use with heavy-gauge speaker wire. Features machined
turned brass construction, large cable clamp and solder tabs that accept up
to 12 gauge wire. 8mm cable entry. • Nickel Shell • Mfg.
#NYS225
Part #NYS225 |
$4.99 |
|
Click on photo for
larger view |
Revisit™
JACK PLATE COMPLETE WITH
SWITCHCRAFT #11 JACK.
Switchcraft #11 jack preinstalled with lock washer and trim washer. Outside diameter 2 inches (51mm). Minor assembly required. Designed to fit flush against a 1 1/8" (29mm) cabinet hole. Easy to install - drill 1 1/8" hole in cabinet, attach speaker wiring to jack and speaker, attach plate to cabinet.
Part #JPC-180 |
$4.95
|
|
|
|
Speaker Hardware |
|
|
Click on photo for
larger view
|
Black Oxide Stainless Steel Pan
Head 10-32 x 1" Speaker Mounting Screws, Rack Mount Screws
Set of 4 screws. Used to mount speakers, back panels, etc in a
variety of amplifiers. 10-32 thread, 1" long with pan head.
May also be used as rack-mount screws. Stainless steel, will not rust.
Part #SC-202A |
$1.79
(for a set of 4 screws) |
|
Click on photo for
larger view |
SPEAKER BAFFLE MOUNTING
STAINLESS STEEL SCREWS AND WASHERS (SET OF 6) FOR Fender™ Blackface and Silverface Series. Set of 6 screws with oval Philips heads, stainless steel #8, 1 3/4 inches long, and matching set of 6 stainless steel cup washers. This set of
six screws w/washers fastens the speaker baffle board to the cabinet on Fender™
blonde, brownface, blackface and silverface combo amps from
the 60s and 70s, and recent reissues of those BF and SF amps. Replaces Fender part number 011678.
Part #SC-407-6 |
$2.29
(for a pack of 6 screws and washers) |
|
Click on photo for
larger view |
Fender™
GRILLE SCREWS (SET OF 4) FOR BROWN, BLONDE, BLACKFACE AND SILVERFACE HEADS. Set of 4 screws, Stainless Steel, 1 3/4" long, Phillips, oval head, with matching cup washers. Fits all
Fender™ vintage heads such as Bassman, Bandmaster, Showman, Dual Showman,
Tremolux,etc and holds the grille to the front of the cabinet.
Part #FGS-4 |
$1.49
(for a pack of 4 screws and 4 washers)
|
|
Click on photo for
larger view |
SPEAKER BAFFLE MOUNTING
4 COPPER SCREWS AND STAINLESS STEEL KEPS NUTS (SET OF 4) FOR Fender™ TWEED AMPS. Set of
4 screws,
copper 6-32, 1 1/2 inches long, Phillips and matching 6-32 Keps Nuts with
integral washers. This set of
four copper screws connects the speaker baffle board to the cabinet on Fender™
tweed combo amps from
the 50s, as well as recent reissue tweed amps such as the Hot Rod Deluxe and 59 Bassman Reissue. Replaces Fender part number 036618 or
0036618049. For amps which require additional baffle screws, see the
individual screw/nut part number SC-415, below.
Part #SC-415-4 |
$3.99
(for a pack of 4 screws and 4 nuts) |
|
Click on photo for
larger view |
SPEAKER BAFFLE MOUNTING
COPPER SCREW AND STAINLESS STEEL KEPS NUT FOR Fender™ TWEED AMPS. Individual
screw, copper 6-32, 1 1/2 inches long, Phillips and matching 6-32 Keps Nut with
integral washer. These screws connect the speaker baffle board to the cabinet on Fender™
tweed combo amps from
the 50s, as well as recent reissue tweed amps such as the Hot Rod Deluxe and 59
Bassman Reissue. Replaces Fender part number 036618 or
0036618049.
Part #SC-415 |
$1.09
(for a single screw with nut)
|
|
Click on photo for
larger view |
FENDER™
SPEAKER MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 12. Locking
nut and washer included. Phillips head. Drill hole, insert and
tighten screws into wood from front of baffle. Install grill cloth, and
you have professional speaker mounting studs. Replacement for
original Fender™ speaker mounting studs. Fender™ part number
0992094000. Set of 12.
Part #SC-409-12 |
$14.95
(For a pack of 12 screws with nuts and lock washers) |
|
Click on photo for
larger view |
FENDER™
SPEAKER MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 4. Locking
nut and washer included. Phillips head. Drill hole, insert and
tighten screws into wood from front of baffle. Install grill cloth, and
you have professional speaker mounting studs. Replacement for
original Fender™ speaker mounting studs. Fender™ part number
0992094000. Set of 4.
Part #SC-409-4 |
$3.99
(For a pack of 4 screws with nuts and lock washers) |
|
Click on photo for
larger view |
ISOLATION WASHER - 3/8" - For #8 Screws
3/8" outside diameter neoprene bonded flat washer. Perfect for
bolting speakers to cabinets. It will securely hold the speaker in place and
stop any rattling. For use with #8 screws. Ideal for vintage Fender
amps with #8 speaker mounting screws. Set of 4 washers.
Part #SIW-38-4 |
$0.59
(For a set of 4 washers) |
|
Click on photo for
larger view |
ISOLATION WASHER - 1/2" - For #10 Screws
Larger 1/2" outside diameter neoprene bonded flat washer. Perfect for
bolting speakers to cabinets. It will securely hold the speaker in place and
stop any rattling. For use with #10 screws, such as a 10-32 machine screw. Set of 4 washers.
Part #SIW-50-4 |
$0.69
(For a set of 4 washers) |
|
Click on photo for
larger view |
KEPS NUT, ZINC, 8-32
THREAD, SET OF 4 NUTS. Typically used on Fender™ Nickel Chassis Straps bolts, and for
speaker mounting.
Works with all 8-32 screws.
Captive lock washer keeps nut tight. Zinc coating retards oxidation.
Sold in a pack of 4.
Part NT-832-4 |
$0.69
(pack of 4 nuts) |
|
WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. 