|
Photo |
Description |
Price |
Purchase |
Click on photo for
larger view |
 Fender™
Amp Tweed Block Logo Revive the look of your vintage-style or modern
Fender™ amp with a genuine Fender™ amplifier logo.
Fender™ tweed amp logo includes mounting pins and is designed for the following
amplifiers: Pro Junior™, Blues Junior™, JazzMaster™ Ultralight. Approx.
2 15/16" wide and 7/8" tall. Original Fender™ part number
0994096000.
Part #FAL-917 |
$25.95
(each) |
|
Click on photo for
larger view |
Fender™ AMP
"TAIL" LOGO. New original Fender™
reproduction. Fender™ logo with
"tail", cast
metal. Similar to the original logo found on blackface amps from the
1960s. Used on the upper left corner of the
grill cloth on most blackface era Fender™ amps. Approx. 4 1/2" wide, the "F" in
the logo is about 2 1/2" inches tall. Original Fender™ part number
0994093000. Mounting screws are included.
Part #FAL-912 |
$25.95
(each) |
|
Click on photo for
larger view |
Fender™ AMP LOGO,
FLAT BLACK. New original Fender™
reproduction, used in many recent and current model Fenders. "Flat" Fender™ logo,
with black "tail", cast
metal, mounting screws included. Used on the upper left corner of the
grill cloth on some recent and vintage era Fender™ amps. Approx. 5 1/2" wide, the "F" in
the logo is about 2 7/8" inches tall. Original Fender™ part
number 0994095000.
Part #FAL-916 |
$25.95
(each) |
|
Click on photo for
larger view
|
Black Logo Mounting Screws
Set of 4 logo mounting screws.
These are #5 x 7/16" black oxide
screws, set of 4. Fit the AL-921 Ampeg logo, and the Fender
FAL-912 logo.
Part #LS-504 |
$0.99
(for a set of 4 screws) |
|
Click on photo for
larger view |
Fender™ LARGE COMBO AMP COSMETIC REFURB KIT For original
1960s blackface and pre-1975 silverface Fender™ Twin Reverb, Super Reverb, Pro Amp, Pro
Reverb, Concert, Vibrosonic models which use 5 5/8" long chassis straps.
(Not designed for the Blackface or Silverface REISSUES. NOT for
vintage Fender™ Speaker Cabinets or Heads, such as Bassman, Bandmaster, Showman,
Tremolux, etc. Not for the Bassman Ten Combo.)
Model not listed? - Contact us. Not for amps made after 1974,
not for reissued blackface and silverface amps. Contains original
Fender™ handle with mounting hardware, 5 5/8" chassis straps with bolts and keps
nuts,
nickel 15/16" glides, set of cabinet corners with mounting screws.
Spruce up the looks of your vintage amp! For additional
refurbishing, see the Fender™ logo plates here,
Fender™ knobs here, Fender™ lamp jewels
here and Fender™ casters
here
Part #FRK-5 |
$34.95 |
|
Click on photo for
larger view |
Fender™ MEDIUM
COMBO AMP COSMETIC REFURB KIT For original
1960s blackface and pre-1975 silverface Fender™ Deluxe, Deluxe Reverb, Princeton,
Princeton Reverb, Tremolux, Musicmaster Bass, Vibrolux Reverb models which use 4 5/8" long chassis straps. (Not designed for the Blackface or Silverface REISSUES. NOT for
vintage Fender™ Speaker Cabinets or Heads, such as Bassman, Bandmaster, Showman,
Tremolux, etc. Not for the Bassman Ten Combo.)
Model not listed? - Contact us. Not for amps made after 1974,
not for reissued blackface and silverface amps. Contains original
Fender™ handle with mounting hardware, 4 5/8" chassis straps with bolts and keps
nuts,
nickel 15/16" glides, set of cabinet corners with mounting screws.
Spruce up the looks of your vintage amp! For additional
refurbishing, see the Fender™ logo plates here,
Fender™ knobs here, Fender™ lamp jewels
here and Fender™ casters
here
Part #FRK-4 |
$33.95 |
|
Click on photo for
larger view |
Fender™ SMALL
COMBO AMP COSMETIC REFURB KIT For original
1960s and pre-1975 silverface Fender™ Champ, Vibro Champ, Bronco models which
use 3 5/8" long chassis straps.
Model not listed? - Contact us. Not for amps made after 1974,
not for reissued blackface and silverface amps. Contains original
Fender™ handle with mounting hardware, 3 5/8" chassis straps with bolts and keps
nuts,
nickel 15/16" glides.
Spruce up the looks of your vintage amp! For additional
refurbishing, see the Fender™ logo plates here,
Fender™ lamp jewels here and Fender™ knobs here
Part #FRK-3 |
$26.95 |
|
Click on photo for
larger view |
CUP WASHER, STAINLESS STEEL, SMALL, SET OF 4. OD 3/8", ID 5/32".
Typically found on the back panel of some Fender™ Blonde/Brown era amps, and some Blackface vintage
amps. Set of 4 washers. Fender™ part number 0037215049. OUTSIDE EDGE OF WASHER IS BARELY
LARGER THAN THE HEAD OF THE Fender™ BACK PANEL SCREWS.
Part # CW-401-4 |
$0.99
(for a set of 4 washers) |
|
Click on photo for
larger view |
CUP WASHER, STAINLESS STEEL, SMALL, SET OF 8. OD 3/8", ID 5/32".
Typically found on the back panel of some Fender™ Blonde/Brown era amps, and some Blackface vintage
amps. Set of 8 washers. Fender™ part number 0037215049. OUTSIDE EDGE OF WASHER IS BARELY
LARGER THAN THE HEAD OF THE Fender™ BACK PANEL SCREWS.
Part # CW-401-8 |
$1.79
(for a set of 8 washers) |
|
Click on photo for
larger view |
CUP WASHER, STAINLESS STEEL, MEDIUM, SET OF 4. OD 7/16", ID 3/16"
Typically found on the back panel of some Fender™ Blackface/Silverface vintage
amps and the reissues of those amps. Larger than the CW-401-4 Currently out of stock. -
Fender™ was not consistent in which washers they used on back panels over the
years. Set of 4 washers.
Part #CW-501-4 |
$0.99
(for a set of 4 washers) |
|
Click on photo for
larger view |
CUP WASHER, STAINLESS STEEL, MEDIUM, SET OF 8. OD 7/16", ID 3/16"
Typically found on the back panel of some Fender™ Blackface/Silverface vintage
amps and the reissues of those amps. Larger than the CW-401-4 Currently out of stock. /
CW-401-8 Currently out of stock. sets -
Fender™ was not consistent in which washers they used on back panels over the
years. Set of 8 washers.
Part #CW-501-8 |
$1.79
(for a set of 8 washers) |
|
Click on photo for
larger view |
Ground Lug Terminals - Angled
Made from tin-plated brass - will not rust. Used to connect a ground wire to a screw and nut on a chassis.
Angled,
with two holes for soldering wires. With built-in lock washer to keep the screw
and nut from loosening. Designed for a #8 size screw.
Pack of 5 terminals.
Part #GL-113 |
$1.39
(Pack of 5 terminals)
|
|
Click on photo for
larger view |
TERMINAL STRIPS, 6 LUG, SET OF
2. Perfect for amplifier circuit additions or modifications.
Center post for mounting to chassis. All 6 terminals are isolated
from ground. Each terminal strip is 2-5/8 inches
long. The lugs are set on 3/8 inch centers. Each lug
will accept wires up to 16ga - smaller gauge allows multiple wires to be
connected to each lug. Set contains 2 terminal strips as pictured.
Mounting hardware not included.
Part #TS-825 |
$2.99
(for a set of 2 terminal strips) |
|
Click on photo for
larger view |
TERMINAL STRIPS, 7 LUG, SET OF
2. Perfect for amplifier circuit additions or modifications.
End terminals on each strip are the mounting lugs, so they become a ground lug
if attached to a metal chassis. Each terminal strip is 2-5/8 inches
long. The lugs are set on 3/8 inch centers. Each lug
will accept wires up to 16ga - smaller gauge allows multiple wires to be
connected to each lug. Set contains 2 terminal strips as pictured.
Mounting hardware not included.
Part #TS-712 |
$3.69
(for a set of 2 terminal strips) |
|
BLACK FENDER HANDLE
Click on photo for
larger view |
ORIGINAL
BLACK Fender™ GUITAR AMP HANDLE.
Black amplifier handle with vinyl sleeve over steel strap and
one-screw mounting nickel-plated end caps. Includes mounting
hardware (two screws and T-nuts).
Introduced on Blonde, Brown, and Blackface™-era Fender™ amplifiers. Used
on 65 Twin Reverb™, 65 Deluxe Reverb™, 65 Super Reverb™, 65 Princeton
Reverb™, 64 Vibroverb Custom, Custom Vibrolux™, Vibro-King™ 212 Enclosure,
Blues Junior™, Pro Junior™, Acoustasonic™ Jr. DSP, Acoustasonic 30, Acoustasonic
SFX II, Bassman™ 25, Bassman 60, Jazzmaster Ultralight™ Enclosure, Princeton
650™, Cyber Champ™, Rumble™ 112, Rumble 2x8, Super-Sonic™ 100 Head, Super-Sonic
Twin, Super Champ™ X2/XD, and Bullet 15 DSP amplifier. Fits most vintage
and modern amplifiers. 7 3/4" center to center screw placement. 9 1/4" handle length without
end caps.
Original Fender™ part number 0990947000.
Part #FAH-332 |
$17.99 |
|
BROWN FENDER HANDLE
Click on photo for
larger view |
ORIGINAL
BROWN Fender™ GUITAR AMP HANDLE.
Brown amplifier handle with vinyl sleeve over steel strap and
one-screw mounting nickel-plated end caps. Includes mounting
hardware (two screws and T-nuts).
Introduced on some Blonde and Brownface-era Fender™ amplifiers. 7 3/4" center to center screw placement. 9 1/4" handle length without
end caps.
Original Fender™ part number 0990944000.
Part #FAH-944 |
$16.99 |
|
Click on photo for
larger view |
GUITAR AMP HANDLE - SIMILAR TO Fender™ HANDLE.
Black handle strap, metal reinforced. Nickel metal caps - may be used
as replacement for vintage
and reissue Fender™ amps. Handle strap is 7/8"
wide. Designed for screw holes set 7 3/4 inches apart.
Looks similar to the original Fender™ part number 0990947000. Screws and T-Nuts included.
Part #FAH-261 |
$8.49 |
|
Click on photo for
larger view |
ORIGINAL 4-SCREW Fender™ GUITAR AMP HANDLE.
Black handle strap, metal reinforced, with nickel-plated end caps - two screws in each end cap. Used on Cyber Twin, Cyber Twin SE, Cyber Deluxe, Stage™
series, Deluxe 90 DSP/900, Ultimate Chorus™, Princeton 65 DSP, 65 Twin Custom™,
94 (Evil) Twin™, "The Twin", Deluxe VM, Bandmaster VM Head, Steel King, Power Chorus, and
Bassman™ 300 amplifiers Includes
mounting screws and nuts.
Fender™ part number 0990948000. 8"
center to center. 9 1/4" handle length without end caps. Also fits
some some Music Man heads and combo amps.
Part #FAH-264 |
$19.95 |
|
|
Click on photo for
larger view |
Fender™ VINTAGE HANDLE SCREWS
Pack of 2 stainless steel handle screws for Fender™
style FAH-332, FAH-261 or FAH-262 handle. 1" Long, 10-32 threads. Designed
to work with a 10-32 T-Nut, in cabinet wood of 3/4" or less.
Will not work with external nut - must be a T-Nut. Will not work
with cabinet wood thicker than 3/4".
See Data Sheet here
Part #SC-403 |
$0.99
(for a pack of 2 screws) |
|
|
Click on photo for
larger view |
Fender™
EXTRA LONG VINTAGE HANDLE SCREWS
Pack of 2 stainless steel extra long handle screws for Fender™
style FAH-332, FAH-261 handle. Used for vintage Fender™ style strap
handles used on speaker cabinets, such as Bandmaster, Bassman, Showman,
and Blonde or Blackface Tremolux. 1-1/4" Long, 10-32 threads. Designed
to work with a 10-32 T-Nut, in cabinet wood of 1-1/8" or less.
Will not work with external nut - must be a T-Nut. Will not work
with cabinet wood thicker than 1-1/8".
See Data Sheet here
Part #SC-403A |
$0.99
(for a pack of 2 screws) |
|
Click on photo for
larger view |
Premium-quality steel T-nuts feature six razor-sharp teeth and extra-long barrels.
1/4"-20 coarse thread.
The result is a T-nut that goes in straighter and holds tighter than ordinary T-nuts. As a bonus, the 6-prong design ensures that your T-nut will stay in place even when working at the edge of a driver hole. We guarantee that these are the finest T-nuts that you will find on the market. Recommended hole size is 1/4", thread is 10-32,
barrel length is 11mm, or about 7/16". Pack of 4 nuts.
Part 6-TNUT-1032 |
$1.59
(pack of 4) |
|
(Brown)
Click on photo for
larger view |
Fender™ STYLE GUITAR AMP HANDLE.
Brown handle strap, "dogbone" style. Nickel end hooks - replacement for vintage
and modern Fender™ amps. Replacement for Fender™ part number 0990946000. Does
not contain Fender™ logo, so it may be used on other brands of amps. Used on vintage
and modern brownface and blonde tolex amps such as the 59 Bassman, Hot Rod
Deluxe, Blues Deluxe, Blues Deville, Super-Sonic etc. Color of handle strap is
brown. Screws not included - order screw SC-402 separately (takes a
pack of 4
screws).
Part #FAH-328 |
$7.99 |
|
(Black)
Click on photo for
larger view |
Fender™ STYLE GUITAR AMP HANDLE.
Black handle strap, "dogbone" style. Nickel end hooks -
replacement for vintage and modern Fender™ amps. Replacement for Fender™ part number 0990943000. Does
not contain Fender™ logo, so it may be used on other brands of amps. Used on vintage
and modern black tolex amps such as the Hot Rod
Deville, Blues Deluxe, Blues Deville, Super-Sonic, etc. Color of handle strap is
black. Screws not included - order screw SC-402 separately (takes a
pack of 4
screws).
Part #FAH-329 |
$7.99 |
|
|
Click on photo for
larger view |
Fender™ "DOGBONE" HANDLE SCREWS
Pack of 4
nickel "Dogbone" handle screws for Fender™
style FAH-328 and FAH-329 handles. Fits the handle on the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, and Blues Deville, as well as other Fender™ amps of similar design. Also
works with Hiwatt handles and other British design amp handles. 8-32
thread.
Part #SC-402 |
$1.59
(for a pack of 4 screws) |
|
Click on photo for
larger view |
Premium-quality steel T-nuts feature
three razor-sharp teeth
and 8-32 fine thread. Works with all 8-32 screws - recommended for mounting
many guitar amp handles. Pack of 4 nuts.
Part TNUT-832 |
99 cents
(pack of 4) |
|
Click on photo for
larger view |
Fender™ VINTAGE STYLE GUITAR AMP HANDLE,
RAISED, MEDIUM BROWN
STITCHED SIMULATED LEATHER.
Medium brown simulated leather handle strap, replacement for Fender™ "tweed" style amps (as
well as other vintage amps). Has slight "raised" bump near the center of the
handle. Medium brown, white stitched. 5-7/8" from post position
to post position, total length of strap when completely flat is 8-3/4". Comes complete with two
nickel-plated handle mounts and four screws.
Part #GAH-282 |
$18.95 |
|
Click on photo for
larger view |
Fender™ or Ampeg™ VINTAGE STYLE GUITAR AMP HANDLE, RAISED,
BLACK STITCHED
SIMULATED LEATHER. Black raised handle strap, made of simulated leather,
replacement for Fender™ "tweed" style amps or vintage Ampeg amps (as well as
other vintage amps). Has slight "raised" bump near the center of the handle.
Black, white stitched. 5-7/8" from post position to post position, total
length of strap when completely flat is 8-3/4". Mounts and screws
are included.
Part #GAH-782 |
$18.95 |
|
Click on photo for
larger view |
HANDLE MOUNTING KIT - FOR STRAP HANDLES
Complete set of hardware for mounting one leather style strap handle,
including machine screws and T-Nuts. Excellent for repairing
strap handles where the old wood screws have pulled out of their holes.
Remove amp chassis, drill new holes with 3/16" or 5mm drill bit, tap in T-Nuts on
the underside and mount the handle. Fits Fender™ "tweed" style
amps and some vintage Ampeg™ amps. Works with our handles GAH-282, GAH-782. Part #THH-2 |
$4.95 |
|
Click on photo for
larger view |
Fender™ Nickel Chassis Straps - Large (5") for Twin, Bassman, Super, Showman, Vibro-King, Pro, Pro Reverb, Prosonic, etc. Includes
2 straps, no screws or nuts.
Screw spacing is 5 inches center-to-center, strap length is 5 5/8"
end-to-end.
Part #FCS-5-2 |
$7.95
(Two chassis straps, screws and nuts NOT included)
|
|
Click on photo for
larger view |
Fender™ Nickel Chassis Straps - Medium (4") For Deluxe, Vibrolux, etc. Includes
2 chassis straps, no screws or nuts.
Screw spacing is 4 inches center-to-center, strap length is 4 5/8"
end-to-end.
Part #FCS-4-2 |
$7.49
(Two 4 in. chassis straps, screws and nuts NOT included) |
|
Click on photo for
larger view |
Fender™ Nickel Chassis Straps - Small (3") For
Champ, Music Master Bass, etc. Includes 2 chassis straps, no screws or
nuts.
Screw spacing is 3 inches center-to-center, strap length is 3 5/8"
end-to-end.
Part #FCS-3-2 |
$6.99
(Two 3 in. chassis straps, screws and nuts NOT included) |
|
Click on photo for
larger view |
Fender™ Chassis Bolt Set -
Works with all Fender™
Nickel or Revisit™ Chassis Straps for Blackface, Silverface
through 1975, and reissued
Blackface models. Includes 4 bolts and 4 matching nuts with integral
lock washers. Fender part number 0022236049.
Part #FCB-4 |
$5.95
(4 bolts, 4 nuts - complete set for one amp) |
|
Click on photo for
larger view |
Fender™ Chassis Bolt Set - Works with all Fender™ Nickel Chassis Straps
on 1976+ and early 80s (ultralinear) Silverface models. Includes 4 bolts
8-32, 1 1/2" long. Stainless steel.
Part #FNCB-4 |
$1.95
(4 bolts - complete set for one amp) |
|
Click on photo for
larger view |
KEPS NUT, ZINC, 6-32
THREAD, SET OF 4 NUTS. Typically used on Fender™ speaker baffle
mounting on vintage and reissue "tweed" amps.
Works with all
6-32 screws.
Captive lock washer keeps nut tight. Zinc coating retards oxidation.
Sold in a pack of 4.
Part NT-632-4 |
$0.59
(pack of 4 nuts) |
|
Click on photo for
larger view |
KEPS NUT, ZINC, 8-32
THREAD, SET OF 4 NUTS. Typically used on Fender™ Nickel Chassis Straps bolts, and for
speaker mounting.
Works with all 8-32 screws.
Captive lock washer keeps nut tight. Zinc coating retards oxidation.
Sold in a pack of 4.
Part NT-832-4 |
$0.69
(pack of 4 nuts) |
|
Click on photo for
larger view |
KEPS NUT, ZINC, 10-32
THREAD, SET OF 4 NUTS. Typically used on Fender™ chassis
mounting screws on vintage "tweed" amps from the 1950s.
Works with all
10-32 screws.
Captive lock washer keeps nut tight. Zinc coating retards oxidation.
Sold in a pack of 4.
Part NT-1032-4 |
$0.79
(pack of 4 nuts) |
|
 |
ORIGINAL Fender™
THUMBSCREWS Fender™ piggyback thumbscrews, holds head to cabinet on
Showman, Bandmaster, Tremolux, Tone Master™
212, Super-Sonic™ 212 and Super-Sonic 60 speaker enclosures and other head/cabinet sets. Heavy
nickel plated
steel, heavy knurling on knob. Set Of Two. Genuine Fender™ part number 0990720000.
Part #TS-251 |
$12.95
(Set of 2 Thumbscrews) |
|
|
|
Fender™
TILT-BACK LEG SCREWS AND CAPTIVE NUTS
Pack of 2 stainless steel tilt-back leg screws,
1-1/2 inches long, along with hex nuts with special nylon inserts. Used on tilt-back legs of larger Fender combo
amps and speaker cabinets. Replaces Fender part numbers 021998 and 022277.
Part #SCW-403T-2 |
$1.79
(for a pack of 2 screws and
2 nuts) |
|
|
|
Fender™
TILT-BACK LEG STOP SCREWS
Pack of 2 stainless steel tilt-back leg stop screws,
3/4 inches long. Used on the tilt-back legs stops of larger Fender combo
amps and speaker cabinets.
Part #SC-506-2 |
$0.99
(for a pack of 2 screws) |
|
Click on photo for
larger view |
BACK
PANEL STAINLESS STEEL SCREWS (SET OF 4) FOR OPEN BACK CABINETS (such as Fender™ Blonde, Brown, Blackface and Silverface
Combo Series). Set of 4 screws, stainless steel, 1 1/4 inches long, Phillips, oval head. This set of four
screws fits either the top or bottom rear panels on Fender™ combo amps from the
50s, 60`s and 70s, and recent reissues of those BF and SF amps. Use with
either the CW-401 or CW-501 cup washers.
Part #SC-401-4 |
$0.99
(for a pack of 4 screws) |
|
Click on photo for
larger view |
BACK
PANEL STAINLESS STEEL SCREWS (SET OF 8) FOR OPEN BACK CABINETS (such as Fender™ Blonde, Brown, Blackface and Silverface
Combo Series). Set of 8 screws, stainless steel, 1 1/4 inches long, Phillips, oval head. This set of
eight screws fits both the top and bottom rear panels on Fender™ combo amps from
the 50s, 60`s and 70s, and recent reissues of those BF and SF amps. Set of 8
completely replaces all of the screws on the two back panels. Use with
either the CW-401 or CW-501 cup washers.
Part #SC-401-8 |
$1.79
(for a pack of 8 screws) |
|
Click on photo for
larger view |
BACK PANEL STAINLESS STEEL SCREWS (SET
OF 8) FOR CLOSED BACK CABINETS (SUCH AS Fender™ Bassman, Bandmaster,
etc ). Set
of 8 screws, Stainless Steel, 1 3/4" long, Phillips, oval head. Use with the
CW-400 cup washers.
Part #SC-400-8 |
$1.99
(for a pack of 8 screws)
|
|
Click on photo for
larger view |
BACK PANEL STAINLESS STEEL SCREWS
(SET OF 28) FOR CLOSED BACK CABINETS (SUCH AS Fender™ BASSMAN 2x12, BANDMASTER
2x12, etc). Set
of 28 #8 screws, Stainless Steel, 1 3/4" long, Phillips, oval head. Use with the
CW-400-28 cup washers. A set of 28 screws completely replaces
all of the screws on most vintage Bassman™ 2x12 and Bandmaster™ 2x12 cabinets
Part #SC-400-28 |
$5.69
(for a pack of 28 screws)
|
|
Click on photo for
larger view |
BACK PANEL STAINLESS STEEL SCREWS
(SET OF 28) FOR CLOSED BACK CABINETS (SUCH AS Fender™ BASSMAN 2x15). Set
of 36 #8 screws, Stainless Steel, 1 3/4" long, Phillips, oval head. Use with the
CW-400-36 cup washers. A set of 36 screws completely replaces
all of the screws on most vintage Bassman™ 2x15 cabinets.
Part #SC-400-36 |
$6.99
(for a pack of 36 screws)
|
|
Click on photo for
larger view |
SATIN BLACK
BACK PANEL
STAINLESS STEEL SCREWS (SET OF 4) FOR OPEN BACK CABINETS (such as Fender™ Blonde, Brown, Blackface and Silverface Series). Set of 4 screws,
satin black stainless steel, 1 1/4 inches long, Phillips, oval head. This set of four
screws fits either the top or bottom rear panels on Fender™ combo amps from the
60`s and 70s, and recent reissues of those BF and SF May be used with the
BCW-10 cup washers. See data sheet
Part #SC-405-4 |
$0.99
(for a pack of 4 screws) |
|
Click on photo for
larger view |
SATIN BLACK BACK PANEL
STAINLESS STEEL SCREWS (SET OF 8) FOR OPEN BACK CABINETS (such as Fender™ Blonde, Brown, Blackface and Silverface Series). Set of 8 screws,
satin black stainless steel, 1 1/4 inches long, Phillips, oval head. This set of
eight screws fits both the top and bottom rear panels on Fender™ combo amps from
the 60`s and 70s, and recent reissues of those BF and SF amps. Set of 8
completely replaces all of the screws on the two back panels. May be used
with the BCW-10 cup washers. See data sheet
Part #SC-405-8 |
$1.89
(for a pack of 8 screws) |
|
Click on photo for
larger view |
CUP WASHER, BLACK METAL, PACK OF 10. Used with #8 Black screws, on
amps and speaker cabinets.
Part #BCW-10 |
$2.49
(pack of 10) |
|
Click on photo for
larger view
|
Black Oxide Stainless Steel Pan
Head 10-32 x 1" Speaker Mounting Screws, Rack Mount Screws
Set of 4 screws. Used to mount speakers, back panels, etc in a
variety of amplifiers. 10-32 thread, 1" long with pan head.
May also be used as rack-mount screws. Stainless steel, will not rust.
Part #SC-202A |
$1.79
(for a set of 4 screws) |
|
Click on photo for
larger view |
SPEAKER BAFFLE MOUNTING
STAINLESS STEEL SCREWS AND WASHERS (SET OF 6) FOR Fender™ Blackface and Silverface Series. Set of 6 screws with oval Philips heads, stainless steel #8, 1 3/4 inches long, and matching set of 6 stainless steel cup washers. This set of
six screws w/washers fastens the speaker baffle board to the cabinet on Fender™
blonde, brownface, blackface and silverface combo amps from
the 60`s and 70s, and recent reissues of those BF and SF amps. Replaces Fender part number 011678.
Part #SC-407-6 |
$2.29
(for a pack of 6 screws and washers) |
|
Click on photo for
larger view |
Fender™
GRILLE SCREWS (SET OF 4) FOR BROWN, BLONDE, BLACKFACE AND SILVERFACE HEADS. Set of 4 screws, Stainless Steel, 1 3/4" long, Phillips, oval head, with matching cup washers. Fits all
Fender™ vintage heads such as Bassman, Bandmaster, Showman, Dual Showman,
Tremolux, etc and holds the grille to the front of the cabinet.
Part #FGS-4 |
$1.49
(for a pack of 4 screws and 4 washers)
|
|
Click on photo for
larger view |
SPEAKER BAFFLE MOUNTING
COPPER SCREWS AND STAINLESS STEEL KEPS NUTS (SET OF 4) FOR Fender™ TWEED AMPS. Set of
4 screws,
copper 6-32, 1 1/2 inches long, Phillips and matching 6-32 Keps Nuts with
integral washers. This set of
four copper screws connects the speaker baffle board to the cabinet on Fender™
tweed combo amps from
the 50s, as well as recent reissue tweed amps such as the Hot Rod Deluxe and 59 Bassman Reissue. Replaces Fender part number 036618 or
0036618049. For amps which require additional baffle screws, see the
individual screw/nut part number SC-415, below.
Part #SC-415-4 |
$3.99
(for a pack of 4 screws and 4 nuts) |
|
Click on photo for
larger view |
SPEAKER BAFFLE MOUNTING
COPPER SCREW AND STAINLESS STEEL KEPS NUT FOR Fender™ TWEED AMPS. Individual
screw, copper 6-32, 1 1/2 inches long, Phillips and matching 6-32 Keps Nut with
integral washer. These screws connect the speaker baffle board to the cabinet on Fender™
tweed combo amps from
the 50s, as well as recent reissue tweed amps such as the Hot Rod Deluxe and 59
Bassman Reissue. Replaces Fender part number 036618 or
0036618049.
Part #SC-415 |
$1.09
(for a single screw with nut)
|
|
Set of 4 screws shown. Set of 5 screws also available.
Click on photo for
larger view
|
SPEAKER BAFFLE MOUNTING
STAINLESS STEEL SCREWS AND STAINLESS STEEL KEPS NUTS (SETS OF 4 OR 5) FOR Fender™
BLUES DELUXE, BLUES DEVILLE, BLUES JUNIOR III, HOT ROD DELUXE OR HOT ROD DEVILLE AMPS WITH
BLACK TOLEX. Sets of either 4 or 5 screws,
stainless steel 6-32, 1 1/2 inches long, flat stainless washers, Phillips and matching 6-32 Keps
Nuts with integral washers. This set of four
nickel style screws
connects the speaker baffle board to the cabinet on Fender™ amps.
Blues Junior III needs the 4-screw set, other larger amps with black tolex need
the 5-screw set.
Replaces Fender part number 050858 or
0050858000. For amps covered in Tweed Tolex, see the SC-415 screws.
Part #SC-414-X |
4-screw set:
$2.79
5-screw set:
$3.29 |
|
Click on photo for
larger view |
Fender™ Style Stainless Steel Corner Screws, Set of
8
Oval-head Phillips corner screws for counter-sunk amp corners,
such as the FVC-2L and FVC-3 Fender™ corners. 3/4 inches long, Phillips head,
stainless steel for long rust-free life. Set
of 8 screws, for four FVC-2L corners.
Part #SC-406-8
|
$2.99
(for a pack of 8 screws) |
|
Click on photo for
larger view |
Fender™ Style Stainless Steel Corner Screws, Set of
12
Oval-head Phillips corner screws for counter-sunk amp corners,
such as the FVC-2L and FVC-3 Fender™ corners. 3/4 inches long, Phillips head,
stainless steel for long rust-free life. Set
of 12 screws, for four FVC-3 corners.
Part #SC-406-12
|
$4.29
(for a pack of 12 screws) |
|
|
Click on photo for
larger view |
Fender™ STAINLESS STEEL BACK-PANEL SCREWS
Pack of 6 stainless steel back panel screws suitable for Fender™ reissue "Tweed" series amps. Fits the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, Blues Junior and Blues Deville, and 59 Bassman reissue.
3/4" long, 10-32 thread. Fender™ Original Part number 0015990049.
Pack of 6 screws. Made of stainless steel, for longer life and no
worries about rust or oxidation.
These screws are not
nickel-plated.
Part #FBP-6 |
$2.99
(for a pack of 6 screws) |
|
|
Click on photo for
larger view |
Fender™ STYLE STAINLESS STEEL CHASSIS MOUNTING SCREWS
Pack of 6 stainless steel chassis mounting screws
suitable for Fender™ reissue "Tweed" series amps.
Mounts the chassis to the cabinet on top as well as the sides of the cabinet. Fits the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe,
Blues Junior, Pro Junior, and Blues Deville, 59 Bassman reissue.
1 1/2" long, 10-32 thread. Replacement for Fender™ Part number
0036619049.
Pack of 6 screws. Made of stainless steel, for longer life and no
worries about rust or oxidation. Note: These screws are not
nickel-plated.
For original Fender screws, see the FGCM-6 set.
Part #FCM-6 |
$2.99
(for a pack of 6 screws) |
|
|
Click on photo for
larger view |
Genuine Fender™
NICKEL-PLATED STEEL CHASSIS MOUNTING SCREWS
Pack of 6 nickel-plated steel chassis mounting screws
suitable for Fender™ reissue "Tweed" series amps.
Mounts the chassis to the cabinet on top as well as the sides of the cabinet. Fits the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe,
Blues Junior, Pro Junior, and Blues Deville, 59 Bassman reissue. 1 1/2" long,
10-32 thread.
Pack of 6 screws. 10-32 X 1-1/2 TH PHS Nickel-Plated Screws.
Genuine Fender™ Original Part number 0036619049.
Part #FGCM-6 |
$5.95
(for a pack of 6 screws) |
|
|
Click on photo for
larger view |
Fender™
STYLE ZINC-PLATED STEEL CABINET WASHERS
Pack of 6 zinc-plated steel cabinet
washers
suitable for Fender™ reissue "Tweed" series amps. Used on
the chassis mounting screws as well as the back-panel mounting screws. Fits the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe,
Blues Junior, Pro Junior, and Blues Deville, 59 Bassman reissue.
Pack of 6 washers. A replacement for Fender™ Part number 0022327049.
Part #FCW-6 |
$0.50
(for a pack of 6 washers) |
|
|
Click on photo for
larger view |
Fender™ STYLE STAINLESS STEEL CHASSIS MOUNTING SCREWS
WITH KEPS NUTS
Pack of 6 stainless steel chassis mounting screws
and matching KEPS nuts for Fender™ original "Tweed" series amps.
Mounts the chassis to the cabinet on top as well as the sides of the cabinet.
Fits the Fender™ original
Tweed amps from the 1950s: Tweed Vibrolux, Tweed Twin, Tweed Tremolux, Tweed Super, Tweed Pro, Tweed Princeton, Tweed Harvard, Tweed Deluxe,
Tweed Champ, and Tweed Bassman. 1 1/2" long, 10-32 thread.
Replacement for Fender™ Original Part number 0992095000.
Pack of 6 screws with 6 nuts.
Screws made of stainless steel, for longer life
and no worries about rust or oxidation. These screws are not
nickel-plated.
Part #FVCM-6 |
$3.99
(for a pack of 6 screws and 6 nuts) |
|
|
Click on photo for
larger view |
Genuine Fender™ NICKEL-PLATED STEEL CHASSIS MOUNTING SCREWS
WITH KEPS NUTS
Pack of 6 nickel-plated steel chassis mounting screws
and matching zinc-plated KEPS nuts for Fender™ original "Tweed" series amps.
Mounts the chassis to the cabinet on top as well as the sides of the cabinet.
Fits the Fender™ original
Tweed amps from the 1950s: Tweed Vibrolux, Tweed Twin, Tweed Tremolux, Tweed Super, Tweed Pro, Tweed Princeton, Tweed Harvard, Tweed Deluxe,
Tweed Champ, and Tweed Bassman. 1 1/2" long, 10-32 thread.
Pack of 6 screws with 6 nuts. 10-32
X 1-1/2 TH PHS Nickel-Plated Screws. Fender™ Original Part number 0992095000.
Part #FGVC-6 |
$6.95
(for a pack of 6 screws and 6 nuts) |
|
|
Click on photo for
larger view |
Fender™ "DOGBONE" HANDLE SCREWS
Pack of 4
nickel "Dogbone" handle screws for Fender™
style FAH-328 and FAH-329 handles. Fits the handle on the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, and Blues Deville, as well as other Fender™ amps of similar design. Also
works with Hiwatt handles and other British design amp handles.
8-32 thread.
Part #SC-402 |
$1.59
(for a pack of 4 screws) |
|
|
Click on photo for
larger view |
Fender™ VINTAGE HANDLE SCREWS
Pack of 2 stainless steel handle screws for Fender™
style FAH-332, FAH-261 handle. 1" Long, 10-32 threads. Designed
to work with a 10-32 T-Nut, in cabinet wood of 3/4" or less.
Will not work with external nut - must be a T-Nut. Will not work
with cabinet wood thicker than 3/4".
See Data Sheet here
Part #SC-403 |
$0.99
(for a pack of 2 screws) |
|
|
Click on photo for
larger view |
Fender™
EXTRA LONG VINTAGE HANDLE SCREWS
Pack of 2 stainless steel extra long handle screws for Fender™
style FAH-332, FAH-261 handle. Used for vintage Fender™ style strap
handles used on speaker cabinets, such as Bandmaster, Bassman, Showman,
and Blonde or Blackface Tremolux. 1-1/4" Long, 10-32 threads. Designed
to work with a 10-32 T-Nut, in cabinet wood of 1-1/8" or less.
Will not work with external nut - must be a T-Nut. Will not work
with cabinet wood thicker than 1-1/8".
See Data Sheet here
Part #SC-403A |
$0.99
(for a pack of 2 screws) |
|
|
Click on photo for
larger view |
Fender™ SELF-TAPPING SCREWS
Used in vintage Fender™ blackface and silverface
amps for a variety of
tasks. Used to attach capacitor pans, tube sockets, transformers on smaller amps, chokes, etc.
Pack of 12 screws. Replaces Fender™ part number 029913.
Part #SC-410-12 |
$3.50
(for a pack of 12 screws) |
|
Click on photo for
larger view |
FENDER™
SPEAKER MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 12. Locking
nut and washer included. Phillips head. Drill hole, insert and
tighten screws into wood from front of baffle. Install grill cloth, and
you have professional speaker mounting studs. Replacement for
original Fender™ speaker mounting studs. Fender™ part number
0992094000. Set of 12.
Part #SC-409-12 |
$14.95
(For a pack of 12 screws with nuts and lock washers) |
|
Click on photo for
larger view |
FENDER™
SPEAKER MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 4. Locking
nut and washer included. Phillips head. Drill hole, insert and
tighten screws into wood from front of baffle. Install grill cloth, and
you have professional speaker mounting studs. Replacement for
original Fender™ speaker mounting studs. Fender™ part number
0992094000. Set of 4.
Part #SC-409-4 |
$3.99
(For a pack of 4 screws with nuts and lock washers) |
|
Click on photo for
larger view |
ISOLATION WASHER - 3/8" - For #8 Screws
3/8" outside diameter neoprene bonded flat washer. Perfect for
bolting speakers to cabinets. It will securely hold the speaker in place and
stop any rattling. For use with #8 screws. Ideal for vintage Fender
amps with #8 speaker mounting screws. Set of 4 washers.
Part #SIW-38-4 |
$0.59
(For a set of 4 washers) |
|
Click on photo for
larger view |
ISOLATION WASHER - 1/2" - For #10 Screws
Larger 1/2" outside diameter neoprene bonded flat washer. Perfect for
bolting speakers to cabinets. It will securely hold the speaker in place and
stop any rattling. For use with #10 screws, such as a 10-32 machine screw. Set of 4 washers.
Part #SIW-50-4 |
$0.69
(For a set of 4 washers) |
|
Click on photo for
larger view |
Vintage Fender™ Combo Style Blackface and Silverface 2-Leg Wrap-Around Cabinet Corner
with Lip - Bright Nickel Plated Steel
(Not designed for the Blackface or Silverface REISSUES. NOT for
vintage Fender™ Speaker Cabinets or Heads, such as Bassman, Bandmaster, Showman, etc)
Recreation of the vintage Fender™ corners with
counter-sunk screw holes. Set of 4, includes screws.
For 1/2" radius corner.
Applicable to the 60s and most 70s Blackface and Silverface amps with
counter-sunk screw holes. NOT FOR the REISSUES! NOT FOR
SPEAKER CABINETS OR HEADS - COMBOS ONLY.
Part #FVC-2L
|
$5.99
(Set of 4 corners with screws) |
|
Click on photo for
larger view |
Vintage Fender™ Style Blackface and Silverface 2-Leg Wrap-Around Cabinet Corner
with Lip - Bright Nickel Plated Steel
(Not designed for the Blackface or Silverface REISSUES. NOT for
vintage Fender™ Speaker Cabinets or Heads, such as Bassman, Bandmaster, Showman,
Tremolux, etc)
Recreation of the vintage Fender™ corners with
counter-sunk screw holes. For 1/2" radius corners. Set of
2, includes oval-head tapered stainless screws.
Part #FVC-2L-2
|
$3.19
(Set of 2 corners with screws) |
|
Click on photo for
larger view |
Vintage Fender™ Style 3-Leg Corners with
counter-sunk screw holes, set of 2. Bright nickel-plated steel. Recreation of the vintage
style corners with
counter-sunk screw holes from the 60s and 70s.
These
corners have 3 legs (two long, one short), for 1/2" radius corners with solid
material on all three sides (no recesses). Typically used as the
rear bottom corners on the Fender Bassman Ten Combo, the Deluxe 112, etc. Set of 2, includes oval-head
tapered stainless screws.
Part #FVC-3
|
$3.50
(Set of 2 corners with screws) |
|
Click on photo for
larger view |
Vintage Fender™ Style 2-Leg and 3-Leg Corners with
counter-sunk screw holes. Bright nickel-plated steel.
Recreation of the vintage style corners with counter-sunk screw holes from
the 60s and 70s. Two FVC-2L type corners with two legs and a lip, and
two FVC-3 corners with three legs. Typically used around the bottom of the
Bassman Ten (or Bassman 10) Combo Amp from 1972 to 1982. Set of 4
corners total - two FVC-2L for the front, and two FVC-3 for the back. Includes oval-head
tapered stainless screws.
Part #FVC-23
|
$6.50
(Set of 4 corners with screws) |
|
Click on photo for
larger view |
Fender™ Style Stainless Steel Corner Screws, Set of
8
Oval-head Phillips corner screws for counter-sunk amp corners,
such as the FVC-2L and FVC-3 Fender™ corners. 3/4 inches long, Phillips head,
stainless steel for long rust-free life. Set
of 8 screws, for four FVC-2L corners.
Part #SC-406-8
|
$2.99
(for a pack of 8 screws) |
|
Click on photo for
larger view |
Fender™ Style Stainless Steel Corner Screws, Set of
12
Oval-head Phillips corner screws for counter-sunk amp corners,
such as the FVC-2L and FVC-3 Fender™ corners. 3/4 inches long, Phillips head,
stainless steel for long rust-free life. Set
of 12 screws, for four FVC-3 corners.
Part #SC-406-12
|
$4.29
(for a pack of 12 screws) |
|
Click on photo for
larger view |
Black Oval-Head Corner Screws, Set of
8
Black oval-head Phillips corner screws for counter-sunk amp corners.
Works with Vox black plastic corners, and Fender style black metal corners with
recessed screw holes. #6 x 3/4 inches long, Phillips head,
black oxide. Screws are beveled under the head for use in countersunk
holes. Length measured from the edge of the head to tip of the
screw. Set
of 8 screws.
Part #SC-411-8 |
$1.50
(For a set of 8 black oval-head Phillips screws) |
|
Click on photo for
larger view |
 Fender™ Style Pop-Out 2" Caster Wheels - Set
of 4.
Great for Fender™ and many other brands of amps or cabinets. Each
wheel capable
supporting 45 lbs, or 180 lbs total for the set of 4. Wheels 2" in
diameter. The same type of removable caster wheels used on Fender™ amps
since the 1960s. Note:
Mounting screws NOT included. Must drill 5/8" hole in bottom of
cabinet to accommodate post for wheel.
Part #FCW-4R |
$30.95
(Set of 4 pop-out casters)
NOT SOLD OUTSIDE the USA
|
|
Click on photo for
larger view |
Fender™ Style Flat Mount 2" Caster Wheels - Set
of 4.
Great for Fender™ and many other brands of amps or cabinets. Each
wheel capable of supporting 45 lbs, or 180 lbs total for the set of 4.
Wheels 2" in diameter. Specifications found
here. Note:
Mounting screws NOT included.
Part #FCW-4F |
$30.95
(Set of 4 casters)
NOT SOLD OUTSIDE the USA |
|
Click on photo for
larger view |
 NICKEL GLIDE FEET,
Revisit™, PACK OF 4, SCREWS INCLUDED.
Nickel cover over rubber foot. 15/16" Diameter, 0.33" Tall.
Replacement for glides used
on many Fender™ amplifiers, including the blackface and silverface designs.
Set of 4, includes 7/8" wood screws. Replaces Fender™ part number 0993900000.
Part #SG-239 |
$4.95
(pack of 4 with screws) |
|
Click on photo for
larger view |
GENUINE Fender™
SPHINX GLIDE FEET, PACK OF 4, SCREWS INCLUDED.
- Set of four metal amplifier cabinet glide feet with
rubber bushings and mounting screws. 1-1/4" diameter.
Fender™ part number 0993900000.
- Fits Cyber-Champ™, Stage™ 100/112SE, Ultimate Chorus,
Princeton 65 DSP/650, GE-112 Enclosure, Tone-Master™ Enclosures, Vibro-King™
212 Enclosure, Pro Reverb, Deluxe 90 DSP/900, Acoustasonic™ 30/SFX II,
Stage™ 1000/1600, Super-Sonic™ Series, Bassman™ Enclosures, Concert™, "The
Twin", 65 Twin Custom™ 15, Steel King™, Hot Rod Deluxe™ Enclosures, Cyber
Deluxe, and Cyber-Twin™ amplifiers.
- Fits most vintage and modern Fender™
amplifiers, but is larger than the traditional 1" diameter glide on
most blackface and silverface amps.
Part #SG-939 |
$12.99
(pack of 4 with screws) |
|
Click on photo for
larger view |
NICKEL GLIDE FEET, Fender™ STYLE, PACK OF 4,
3 PRONG HAMMER TYPE.
Older style 3-prong glide feet for Fender™
amplifiers - metal cap has 3 prongs, and the cap is hammered into the base of
the amplifier.
Part #CG-068 |
$3.95
(pack of 4) |
|
Click on photo for
larger view |
 Capacitor cover for
Fender™ Twin Reverb and other full-size Fender™ silverface and blackface
amps, such as the Super Reverb, Pro Reverb, Bandmaster and Bassman heads. Mounting centers are 7" x 3.5" Measurements are 7 1/8" x 3
1/2" x 1 1/4". Original Fender™ part number 0037854000.
Part #CC-170 |
$34.95 |
|
WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. 
