BALL
HEAD MESH GRILLE AND WINDSCREEN FOR SHURE™ Fits
the majority of "58-style" microphones, including the Shure™
SM58, SM48, Beta 58A, SM58LC, SV100, RK143G, PGX2, Pyle™
PDMIC58, and virtually any other ball-style handheld microphone.
Save with this excellent
Revisit™
reproduction at a fraction of the cost of the
replacement Shure™
grille. Part #MG-58
$9.95
Click on photo for
larger view
Ampeg™ "a" Logo Used on modern Ampeg Speaker Cabinets, this 3 inch x 4 inch plastic logo is
affordably priced. Mounting screws not included. Use
LS-504 for mounting screws.
Mounting centers are
2 1/4" x 2 ⅜". Part #AL-921
$5.95
Click on photo for
larger view
Black Logo Mounting Screws Set of 4 logo mounting screws.
These are #5 x 7/16" black oxide
screws, set of 4. Fit the AL-921 Ampeg logo, and the Fender
FAL-912 logo. Part #LS-504
$0.99
(for a set of 4 screws)
Click on photo for
larger view
Fender™
Amp Tweed Block Logo Revive the look of your vintage-style or modern
Fender™ amp with a genuine Fender™ amplifier logo.
Fender™ tweed amp logo includes mounting pins and is designed for the following
amplifiers: Pro Junior™, Blues Junior™, JazzMaster™ Ultralight. Approx.
2 15/16" wide and 7/8" tall. Original Fender™ part number
0994096000.
Part #FAL-917
$25.95
(each)
Click on photo for
larger view
Fender™ AMP
"TAIL" LOGO. New original Fender™
reproduction. Fender™ logo with
"tail", cast
metal. Similar to the original logo found on blackface amps from the
1960s. Used on the upper left corner of the
grill cloth on most blackface era Fender™ amps. Approx. 4 1/2" wide, the "F" in
the logo is about 2 1/2" inches tall. Original Fender™ part number
0994093000. Mounting screws are included.
Part #FAL-912
$25.95
(each)
Click on photo for
larger view
Fender™ AMP LOGO,
FLAT BLACK. New original Fender™
reproduction, used in many recent and current model Fenders. "Flat" Fender™ logo,
with black "tail", cast
metal, mounting screws included. Used on the upper left corner of the
grill cloth on some recent and vintage era Fender™ amps. Approx. 5 1/2" wide, the "F" in
the logo is about 2 7/8" inches tall. Original Fender™ part
number 0994095000.
Part #FAL-916
$25.95
(each)
Click on photo for
larger view
Marshall™
LOGO, WHITE PLASTIC, 6" LONG The mini Marshall™ logo - smallest size. As used on the
DSL201 combo, DSL401 combo, some of the smaller sized MG series combos, VS15,
VS30R, 1912 Cab, JCM600, JCM602, AS50, 3005, 4501, 5005, 8010, 8015, MG10,
MG10MKII, MG15RCD, MG30RCD, MG215RCD, TSL602, JCM3005, and some other models.
This logo is 6" long - please measure the old logo in order to ensure that you
order the correct size. Part #ML-601
$38.95
Since
Marshall has new ownership for the past year, Marshall hardware parts are
becoming nearly impossible to replenish.
Availability date uncertain. Has been on backorder from Marshall since
May, 2023.
Click on photo for
larger view
Marshall™ LOGO, WHITE PLASTIC, 9" LONG
- TSL122 The 9 inch long Marshall™ logo - medium size. As used on the
TSL122 combo. This logo is 9" long - please measure the old logo in order to ensure that you
order the correct size. Part #ML-901
$38.95
Availability date uncertain. Has been on backorder from Marshall since
May, 2023.
Click on photo for
larger view
Marshall™
LOGO, WHITE PLASTIC, 11" LONG The 11 inch long Marshall™ logo - large size. As used on the 2100,
2205, 2203, 2204, 2210, 2550, 2553, 2554, 2558, 4102, 4001, 4210, 4211, 4212,
4100, 4101, 4103, 4010, 4500, 5213, 5210, 5212, DSL100, 1986, 1960B
cabinet, 1959JMP, 1936, TSL100, 6100, 6101, JCM1959, 2558V, 3005, 2555SL,
AS1960, 2100SLX, TSL60, 1987JCM, DSL50, 3005, 1960AX, and some other models This logo is
11" long - please measure the old logo in order to ensure that you order the
correct size. Part #ML-1101
$39.95
Availability date uncertain. Has been on backorder from Marshall since
May, 2023.
Click on photo for
larger view
Marshall™
REAR VENT, GOLD MESH, JTM AND JMP SERIES
NOTE: This is NOT the top vent! This original Marshall vent is for the H-shaped head back panels on the
vintage JMP and JTM amps from the 1960s. Check the measurement on
your back panel - the MV-210 vent measures 16 7/8" x 2 1/4". Part #MV-210
$34.95
Click on photo for
larger view
Marshall™
TOP VENT, 8 SCREW OR RIVET HOLES, MOST JCM800 AND JCM900 HEADS This original Marshall vent is for most JCM800 and JCM900 heads from the
1980s and 1990s. Check the measurement of your existing vent - the MV-211
vent measures 17 5/8" x 3". Rivets/screws not included. Part #MV-211
$13.95
Availability date uncertain. Has been on backorder from Marshall since
December, 2023.
Click on photo for
larger view
Marshall™
TOP VENT, POP-IN, FOR CERTAIN VALVESTATE AVT MODELS This original Marshall vent is for the AVT50, AVT100, and AVT275 heads and
combos. Replaces the plastic vent immediately behind the handle, and
is roughly the size of the handle. Check the measurement of your existing vent - the MV-218
vent measures 10 1/4" x 1 9/16" Part #MV-218
$8.95
Click on photo for
larger view
Vox™
BRASS VENT, VINTAGE STYLE Found on several vintage Vox™
amps from the 1960s, including the original AC15 and AC30. The vintage Vox™ amps
typically used 3 of these vents across the top of the cabinet. This
recreation from Tube Amp Doctor is hand-crafted in Germany to be a perfect match
for the original brass vents.
Measures 0.720" x 4.805" (122 x 18.3mm).
Sold individually. Special order, allow 3 business days.
Part #VV-225
$14.50
Click on photo for
larger view
CUP WASHER, BLACK METAL, PACK OF 10. Used with #8 Black screws, on
amps and speaker cabinets. Part #BCW-10
$2.49
(pack of 10)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, SMALL, SET OF 4. OD 3/8", ID 5/32".
Typically found on the back panel of some Fender™ Blonde/Brown era amps, and some Blackface vintage
amps. Set of 4 washers. Fender™ part number 0037215049. OUTSIDE EDGE OF WASHER IS BARELY
LARGER THAN THE HEAD OF THE Fender™ BACK PANEL SCREWS.
Part # CW-401-4 Currently out of stock.
$0.99
(for a set of 4 washers)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, SMALL, SET OF 8. OD 3/8", ID 5/32".
Typically found on the back panel of some Fender™ Blonde/Brown era amps, and some Blackface vintage
amps. Set of 8 washers. Fender™ part number 0037215049. OUTSIDE EDGE OF WASHER IS BARELY
LARGER THAN THE HEAD OF THE Fender™ BACK PANEL SCREWS.
Part # CW-401-8 Currently out of stock.
$1.79
(for a set of 8 washers)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, MEDIUM, SET OF 4. OD 7/16", ID 3/16"
Typically found on the back panel of some Fender™ Blackface/Silverface vintage
amps and the reissues of those amps. Larger than the CW-401-4 Currently out of stock. -
Fender™ was not consistent in which washers they used on back panels over the
years. Set of 4 washers.
Part #CW-501-4
$0.99
(for a set of 4 washers)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, MEDIUM, SET OF 8. OD 7/16", ID 3/16"
Typically found on the back panel of some Fender™ Blackface/Silverface vintage
amps and the reissues of those amps. Larger than the CW-401-4 Currently out of stock. /
CW-401-8 Currently out of stock. sets -
Fender™ was not consistent in which washers they used on back panels over the
years. Set of 8 washers.
Part #CW-501-8
$1.79
(for a set of 8 washers)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 4. OD 1/2", ID 3/16"
Typically found on larger combo amp cabinets and 4x12 cabinets, such as
Marshall™ . Set of 4 washers.
Part #CW-400-4
$0.99
(for a set of 4 washers)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 8. OD 1/2", ID 3/16"
Typically found on larger combo amp cabinets and 4x12 cabinets, such as
Marshall™ . Set of 8 washers.
Part #CW-400-8
$1.95
(for a set of 8 washers)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 17. OD 1/2", ID 3/16"
Typically found on larger combo amp cabinets and 4x12 cabinets, such as
Marshall™ . Set of 17 washers. Some of the larger Marshall
4x12 cabinets, such as certain model 1960 cabinets, have 17 screws and washers
in the back panel.
Part #CW-400-17
$3.79
(for a set of 17 washers)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF
28. OD 1/2", ID 3/16"
Complete set of 28 stainless steel cup washers for the vintage Fender Bassman
2x12 and Bandmaster 2x12 cabinets. Set of 28 washers. Use
with the SC-400-28 set of screws.
Part #CW-400-28
$5.59
(for a set of 28 washers)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF
36. OD 1/2", ID 3/16"
Complete set of 36 stainless steel cup washers for the vintage Fender Bassman
2x15 cabinets. Set of 36 washers. Use
with the SC-400-36 set of screws.
Part #CW-400-36
$6.89
(for a set of 36 washers)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, EXTRA LARGE. OD 9/16", ID 1/4"
Typically found on larger 4x12 cabinets, and other pro audio speaker cabinet
applications. Set of 4 washers.
Part #CW-502-4
$0.99
(for a set of 4 washers)
Click on photo for
larger view
JACK LOCK WASHER, METAL Replacement lock washer for all Alpha pots with 3/8" bushing and Mesa Boogie pots,
as well as Switchcraft 1/4" jacks. Part #W-38
$0.49
Click on photo for
larger view
SAVE WITH MULTIPACK!
JNUT-38 JACK NUT AND WASHER, METAL,
SWITCHCRAFT™, SET OF 6 Genuine Switchcraft™ nut and washer set for the blackface/silverface Fender™ bias pot, Mesa Boogie pots, and the
CTS or Alpha pots with 3/8" bushing (found on original vintage Fender™
blackface and silverface), as well as Peavey™ and Switchcraft™
1/4" jacks. Does NOT fit the 24mm Marshall™ pots. Set of
6 washers and 6 nuts. Part #JNUT-38-6
$4.50
(Set of 6 washers and 6 nuts)
JACK NUT AND WASHER, METAL,
SWITCHCRAFT™ Genuine Switchcraft™ nut and washer set for the blackface/silverface Fender™ bias pot, Mesa Boogie pots, and the
CTS or Alpha pots with 3/8" bushing (found on original vintage Fender™
blackface and silverface), as well as Peavey™ and Switchcraft™
1/4" jacks. Does NOT fit the 24mm Marshall™ pots. Part #JNUT-38
$0.89
(Set of 1 washer and 1 nut)
Click on photo for
larger view. Jack is in the picture to demonstrate how the washers
are installed - jack is NOT included with the washers.
INSULATING SHOULDER WASHER, FIBER Pair of fiber insulating shoulder washers for Switchcraft jacks with metal
bushings. Used to mount standard jacks in a 1/2" diameter chassis
hole, while insulating the metal bushing (ground) of the jack from the chassis.
ID 3/8", OD 1/2". Works great when replacing isolated plastic jacks with a
more durable metal jack, which is frequently done on the input jacks of the
Fender™ Hot Rod Deville/Deluxe and Blues Deville/Deluxe. Two washers
are used on each jack, and the "shoulders" are placed facing each other through
the chassis. The washers not only isolate the ground of the jack
electrically for noise reduction, but also stabilize the jack in the 1/2"
diameter hole. Jack shown in picture NOT included. Works
well with the Switchcraft J-11, J-L11, J-12A, J-L12A, J-12B, J-L12B, J-13,
J-13A, J-112APC, J-112BX, J-114BX, J-521 and J-524 jacks. Part #ISW-3069
$0.49
(For a pair of washers. Each jack needs two washers.)
Click on photo for
larger view
Fender™ Nickel Chassis Straps - Large (5") for Twin, Bassman, Super, Showman, Vibro-King, Pro, Pro Reverb, Prosonic, etc. Includes
2 straps, no screws or nuts.Screw spacing is 5 inches center-to-center, strap length is 5 5/8"
end-to-end. Part #FCS-5-2
$7.95
(Two chassis straps, screws and nuts NOT included)
Click on photo for
larger view
Fender™ Nickel Chassis Straps - Medium (4") For Deluxe, Vibrolux, etc. Includes
2 chassis straps, no screws or nuts.Screw spacing is 4 inches center-to-center, strap length is 4 5/8"
end-to-end. Part #FCS-4-2
$7.49
(Two 4 in. chassis straps, screws and nuts NOT included)
Click on photo for
larger view
Fender™ Nickel Chassis Straps - Small (3") For
Champ, Music Master Bass, etc. Includes 2 chassis straps, no screws or
nuts.Screw spacing is 3 inches center-to-center, strap length is 3 5/8"
end-to-end. Part #FCS-3-2
$6.99
(Two 3 in. chassis straps, screws and nuts NOT included)
Click on photo for
larger view
Mesa/Boogie™ Nickel Chassis Strap - Large (6"),
bright nickel finish. Single chassis strap, no screws. Screw spacing is 5.31 inches center-to-center, strap length is
6 inches
end-to-end.
Original Mesa/Boogie part number 407520. Sold individually -
ordering quantity of 1 delivers 1 strap. Part #MBCS-6
$8.50
(Sold individually - One chassis strap, screws NOT included)
Click on photo for
larger view
Fender™ Chassis Bolt Set -
Works with all Fender™
Nickel or Revisit™ Chassis Straps for Blackface, Silverface
through 1975, and reissued
Blackface models. Includes 4 bolts and 4 matching nuts with integral
lock washers. Fender part number 0022236049. Part #FCB-4
$5.95
(4 bolts, 4 nuts - complete set for one amp)
Click on photo for
larger view
Mesa/Boogie™
Stainless Steel
Screw - 4 inches long, 10-24 thread. Used with the MBCS-6
chassis straps.Original Mesa/Boogie part number
302190. Sold individually - ordering quantity of 1 delivers 1 screw.
Each amplifier requires a total of 4 screws. Part #MBCB
$1.39
(Sold individually - Each amp uses 4 screws)
Click on photo for
larger view
Fender™ Chassis Bolt Set - Works with all Fender™ Nickel Chassis Straps
on 1976+ and early 80s (ultralinear) Silverface models. Includes 4 bolts
8-32, 1 1/2" long. Stainless steel. Part #FNCB-4
$1.95
(4 bolts - complete set for one amp)
Click on photo for
larger view
Peavey™
Stainless Steel
Screw - 4 inches long, 10-24 thread. Used on a variety of vintage
Peavey amps which had chassis straps on top of the amp cabinet. Sold individually - ordering quantity of 1 delivers 1 screw.
Each amplifier requires a total of 4 screws. Part #PBCB
$1.39
(Sold individually - Each amp uses 4 screws)
Click on photo for
larger view
Fender™ STAINLESS STEEL BACK-PANEL SCREWS
Pack of 6 stainless steel back panel screws suitable for Fender™ reissue "Tweed" series amps. Fits the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, Blues Junior and Blues Deville, and 59 Bassman reissue.
3/4" long, 10-32 thread. Fender™ Original Part number 0015990049.
Pack of 6 screws. Made of stainless steel, for longer life and no
worries about rust or oxidation.
These screws are not
nickel-plated. Part #FBP-6
$2.99
(for a pack of 6 screws)
Click on photo for
larger view
Fender™ STYLE STAINLESS STEEL CHASSIS MOUNTING SCREWS
Pack of 6 stainless steel chassis mounting screws
suitable for Fender™ reissue "Tweed" series amps.
Mounts the chassis to the cabinet on top as well as the sides of the cabinet. Fits the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe,
Blues Junior, Pro Junior, and Blues Deville, 59 Bassman reissue.
1 1/2" long, 10-32 thread. Replacement for Fender™ Part number
0036619049.
Pack of 6 screws. Made of stainless steel, for longer life and no
worries about rust or oxidation. Note: These screws are not
nickel-plated.
For original Fender screws, see the FGCM-6 set. Part #FCM-6
$2.99
(for a pack of 6 screws)
Click on photo for
larger view
Genuine Fender™
NICKEL-PLATED STEEL CHASSIS MOUNTING SCREWS
Pack of 6 nickel-plated steel chassis mounting screws
suitable for Fender™ reissue "Tweed" series amps.
Mounts the chassis to the cabinet on top as well as the sides of the cabinet. Fits the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe,
Blues Junior, Pro Junior, and Blues Deville, 59 Bassman reissue. 1 1/2" long,
10-32 thread.
Pack of 6 screws. 10-32 X 1-1/2 TH PHS Nickel-Plated Screws.
Genuine Fender™ Original Part number 0036619049.
Part #FGCM-6
$5.95
(for a pack of 6 screws)
Click on photo for
larger view
Fender™
STYLE ZINC-PLATED STEEL CABINET WASHERS
Pack of 6 zinc-plated steel cabinet
washers
suitable for Fender™ reissue "Tweed" series amps. Used on
the chassis mounting screws as well as the back-panel mounting screws. Fits the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe,
Blues Junior, Pro Junior, and Blues Deville, 59 Bassman reissue.
Pack of 6 washers. A replacement for Fender™ Part number 0022327049. Part #FCW-6
$0.50
(for a pack of 6 washers)
Click on photo for
larger view
Fender™ STYLE STAINLESS STEEL CHASSIS MOUNTING SCREWS
WITH KEPS NUTS
Pack of 6 stainless steel chassis mounting screws
and matching KEPS nuts for Fender™ original "Tweed" series amps.
Mounts the chassis to the cabinet on top as well as the sides of the cabinet.
Fits the Fender™ original
Tweed amps from the 1950s: Tweed Vibrolux, Tweed Twin, Tweed Tremolux, Tweed Super, Tweed Pro, Tweed Princeton, Tweed Harvard, Tweed Deluxe,
Tweed Champ, and Tweed Bassman. 1 1/2" long, 10-32 thread.
Replacement for Fender™ Original Part number 0992095000.
Pack of 6 screws with 6 nuts.
Screws made of stainless steel, for longer life
and no worries about rust or oxidation. These screws are not
nickel-plated. Part #FVCM-6
$3.99
(for a pack of 6 screws and 6 nuts)
Click on photo for
larger view
Genuine Fender™ NICKEL-PLATED STEEL CHASSIS MOUNTING SCREWS
WITH KEPS NUTS
Pack of 6 nickel-plated steel chassis mounting screws
and matching zinc-plated KEPS nuts for Fender™ original "Tweed" series amps.
Mounts the chassis to the cabinet on top as well as the sides of the cabinet.
Fits the Fender™ original
Tweed amps from the 1950s: Tweed Vibrolux, Tweed Twin, Tweed Tremolux, Tweed Super, Tweed Pro, Tweed Princeton, Tweed Harvard, Tweed Deluxe,
Tweed Champ, and Tweed Bassman. 1 1/2" long, 10-32 thread.
Pack of 6 screws with 6 nuts.10-32
X 1-1/2 TH PHS Nickel-Plated Screws. Fender™ Original Part number 0992095000.
Part #FGVC-6
$6.95
(for a pack of 6 screws and 6 nuts)
ORIGINAL Fender™
THUMBSCREWS Fender™ piggyback thumbscrews, holds head to cabinet on
Showman, Bandmaster, Tremolux, Tone Master™
212, Super-Sonic™ 212 and Super-Sonic 60 speaker enclosures and other head/cabinet sets. Heavy nickel plated
steel, heavy knurling on knob. Set Of Two. Genuine Fender™ part number 0990720000. Part #TS-251
$12.95
(Set of 2 Thumbscrews)
Fender™
TILT-BACK LEG SCREWS AND CAPTIVE NUTS
Pack of 2 stainless steel tilt-back leg screws,
1-1/2 inches long, along with hex nuts with special nylon inserts. Used on tilt-back legs of larger Fender combo
amps and speaker cabinets. Replaces Fender part numbers 021998 and
022277. Part #SCW-403T-2
$1.79
(for a pack of 2 screws and
2 nuts)
Fender™
TILT-BACK LEG STOP SCREWS
Pack of 2 stainless steel tilt-back leg stop screws,
3/4 inches long. Used on the tilt-back legs stops of larger Fender combo
amps and speaker cabinets. Part #SC-506-2
$0.99
(for a pack of 2 screws)
Click on photo for
larger view
BACK PANEL
STAINLESS STEEL SCREWS (SET OF 4) FOR OPEN BACK CABINETS (such as Fender™ Blonde, Brown, Blackface and Silverface Series). Set of 4 screws, stainless steel, 1 1/4 inches long, Phillips, oval head. This set of four
screws fits either the top or bottom rear panels on Fender™ combo amps from the 60s and 70s, and recent reissues of those BF and SF amps. Use with
either the CW-401 or CW-501 cup washers. Part #SC-401-4
$0.99
(for a pack of 4 screws)
Click on photo for
larger view
BACK PANEL
STAINLESS STEEL SCREWS (SET OF 8) FOR OPEN BACK CABINETS (such as Fender™ Blonde, Brown, Blackface and Silverface Series). Set of 8 screws, stainless steel, 1 1/4 inches long, Phillips, oval head. This set of
eight screws fits both the top and bottom rear panels on Fender™ combo amps from the 60s and 70s, and recent reissues of those BF and SF amps. Set of 8
completely replaces all of the screws on the two back panels. Use with
either the CW-401 or CW-501 cup washers. Part #SC-401-8
$1.79
(for a pack of 8 screws)
Click on photo for
larger view
SATIN BLACKBACK PANEL
STAINLESS STEEL SCREWS (SET OF 4) FOR OPEN BACK CABINETS (such as Fender™ Blonde, Brown, Blackface and Silverface Series). Set of 4 screws,
satin black stainless steel, 1 1/4 inches long, Phillips, oval head. This set of four
screws fits either the top or bottom rear panels on Fender™ combo amps from the
60s and 70s, and recent reissues of those BF and SF May be used with the
BCW-10 cup washers. See data sheet Part #SC-405-4
$0.99
(for a pack of 4 screws)
Click on photo for
larger view
SATIN BLACK BACK PANEL
STAINLESS STEEL SCREWS (SET OF 8) FOR OPEN BACK CABINETS (such as Fender™ Blonde, Brown, Blackface and Silverface Series). Set of 8 screws,
satin black stainless steel, 1 1/4 inches long, Phillips, oval head. This set of
eight screws fits both the top and bottom rear panels on Fender™ combo amps from
the 60s and 70s, and recent reissues of those BF and SF amps. Set of 8
completely replaces all of the screws on the two back panels. May be used
with the BCW-10 cup washers. See data sheet Part #SC-405-8
$1.89
(for a pack of 8 screws)
Click on photo for
larger view
CUP WASHER, BLACK METAL, PACK OF 10. Used with #8 Black screws, on
amps and speaker cabinets. Part #BCW-10
$2.49
(pack of 10)
Click on photo for
larger view
SPEAKER BAFFLE MOUNTING
STAINLESS STEEL SCREWS AND WASHERS (SET OF 6) FOR Fender™ Blackface and Silverface Series. Set of 6 screws with oval Philips heads, stainless steel #8, 1 3/4 inches long, and matching set of 6 stainless steel cup washers. This set of
six screws w/washers fastens the speaker baffle board to the cabinet on Fender™
blonde, brownface, blackface and silverface combo amps from
the 60s and 70s, and recent reissues of those BF and SF amps. Replaces Fender part number 011678. Part #SC-407-6
$2.29
(for a pack of 6 screws and washers)
Click on photo for
larger view
Fender™
GRILLE SCREWS (SET OF 4) FOR BROWN, BLONDE, BLACKFACE AND SILVERFACE HEADS. Set of 4 screws, Stainless Steel, 1 3/4" long, Phillips, oval head, with matching cup washers. Fits all
Fender™ vintage heads such as Bassman, Bandmaster, Showman, Dual Showman,
Tremolux,etc and holds the grille to the front of the cabinet. Part #FGS-4
$1.49
(for a pack of 4 screws and 4 washers)
Click on photo for
larger view
SPEAKER BAFFLE MOUNTING
COPPER SCREWS AND STAINLESS STEEL KEPS NUTS (SET OF 4) FOR Fender™ TWEED AMPS. Set of
4 screws,
copper 6-32, 1 1/2 inches long, Phillips and matching 6-32 Keps Nuts with
integral washers. This set of
four copper screws connects the speaker baffle board to the cabinet on Fender™
tweed combo amps from
the 50s, as well as recent reissue tweed amps such as the Hot Rod Deluxe and 59 Bassman Reissue. Replaces Fender part number 036618 or
0036618049. For amps which require additional baffle screws, see the
individual screw/nut part number SC-415, below. Part #SC-415-4
$3.99
(for a pack of 4 screws and 4 nuts)
Click on photo for
larger view
SPEAKER BAFFLE MOUNTING
COPPER SCREW AND STAINLESS STEEL KEPS NUT FOR Fender™ TWEED AMPS. Individual
screw, copper 6-32, 1 1/2 inches long, Phillips and matching 6-32 Keps Nut with
integral washer. These screws connect the speaker baffle board to the cabinet on Fender™
tweed combo amps from
the 50s, as well as recent reissue tweed amps such as the Hot Rod Deluxe and 59
Bassman Reissue. Replaces Fender part number 036618 or
0036618049. Part #SC-415
$1.09
(for a single screw with nut)
Set of 4 screws shown. Set of 5 screws also available.
Click on photo for
larger view
SPEAKER BAFFLE MOUNTING
STAINLESS STEEL SCREWS AND STAINLESS STEEL KEPS NUTS (SETS OF 4 OR 5) FOR Fender™
BLUES DELUXE, BLUES DEVILLE, BLUES JUNIOR III, HOT ROD DELUXE OR HOT ROD DEVILLE AMPS WITH
BLACK TOLEX. Sets of either 4 or 5 screws,
stainless steel 6-32, 1 1/2 inches long, flat stainless washers, Phillips and matching 6-32 Keps
Nuts with integral washers. This set of four
nickel style screws
connects the speaker baffle board to the cabinet on Fender™ amps.
Blues Junior III needs the 4-screw set, other larger amps with black tolex need
the 5-screw set.
Replaces Fender part number 050858 or
0050858000. For amps covered in Tweed Tolex, see the SC-415 screws. Part #SC-414-X
4-screw set:
$2.79
5-screw set:
$3.29
Click on photo for
larger view
Black Oxide Stainless Steel Pan
Head 10-32 x 1" Speaker Mounting Screws, Rack Mount Screws Set of 4 screws. Used to mount speakers, back panels, etc in a
variety of amplifiers. 10-32 thread, 1" long with pan head.
May also be used as rack-mount screws. Stainless steel, will not rust.
Part #SC-202A
$1.79
(for a set of 4 screws)
Click on photo for
larger view
Black Oxide Stainless Steel Pan
Head 4-40 x 5/16" Screws and Nuts, Set of 4 Set of 4 small black screws with matching nuts. Stainless steel
with black oxide finish. Used in a variety of applications on both guitars
and amplifiers. Part #SCBN-440
$1.69
(for a set of 4 screws with nuts)
Click on photo for
larger view
#8 BACK PANEL STAINLESS STEEL SCREWS (SET
OF 8) FOR OPEN BACK CABINETS. Set
of 8 screws, Stainless Steel, #8, 1 1/4" long, Phillips, oval head. Used with the
CW-400 cup washers. These screws are larger in diameter than the typical Fender back panel screws, but fit a number of other combo amps with
open-back cabinets.
Part #SC-2265-8
$1.59
(for a pack of 8 screws)
Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS (SET OF 8) FOR CLOSED BACK CABINETS (SUCH AS
Marshall™). Set
of 8 screws, Stainless Steel, 1 3/4" long, Phillips, oval head. Use with the
CW-400-8 cup washers.
Part #SC-400-8
$1.99
(for a pack of 8 screws)
Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS
(SET OF 17) FOR CLOSED BACK CABINETS (SUCH AS Marshall™). Set
of 17 screws, Stainless Steel, 1 3/4" long, Phillips, oval head. Use with the
CW-400-17 cup washers. A set of 17 screws completely replaces
all of the screws on most Marshall™ 4x12 cabinets, including the 1960 models.
Part #SC-400-17
$3.89
(for a pack of 17 screws)
Click on photo for
larger view
Marshall™
HEAD BACK PANEL STAINLESS STEEL SCREWS AND WASHERS
(SET OF 4) FOR FULL SIZE HEADS. Set of 4 screws, Stainless Steel, 1 1/2" long, Phillips, oval head, with matching cup washers.
Fits most large Marshall™ heads starting in the 1990s, including the JCM-800,
JCM-900, JCM-2000 and JVM series.
Note: The screw heads in this package have a slight oval shape, as opposed
to many Marshall™ head back panel screws which have a flat head. This oval
shape helps improve the "bite" of the screwdriver, and helps prevent the screw
head from being mangled over time.
Part #MBP-4
$1.49
(for a pack of 4 screws and 4 washers)
Click on photo for
larger view
Marshall™
METRIC HANDLE SCREWS
Pack of 2 metric handle screws for Marshall™
MAH-294 handle. Original Marshall™ , designed to work with the OEM
metric T-Nuts. Set of 2 Flat-head counter-sunk Phillips,
M5 x 0.8, length 25 mm.
Found primarily on
JCM900, JCM2000, larger Valvestate, and JVM series amps.
Part #SC-404
$1.99
(for a pack of 2 Marshall™ metric screws)
Click on photo for
larger view
Marshall™
SMALL BRASS PAN-HEAD SCREWS WITH LOCK WASHERS AND NUTS (SET OF 6). Set
of 6 screws, brass, 3/8" (9.5mm) long, slotted pan head - head is 5.4mm in diameter, 4-40
thread, with lock washer and nut. Used to mount preamp tube sockets
and impedance selectors in classic Marshall™
amps.
Part #MSBS-6
$1.99
(for a pack of 6 screws, 6 lock washers and 6 nuts)
Click on photo for
larger view
Marshall™
SMALL BRASS ROUND-HEAD SCREWS WITH LOCK WASHERS AND NUTS (SET OF 6). Set
of 6 screws, brass, 1/2" (12.7mm) long, slotted round head - head is 5.4mm in diameter, 4-40
thread, with lock washer and nut. Used to mount impedance selectors
and IEC power cord connectors in classic Marshall™
amps.
Part #MLBS-6
$2.49
(for a pack of 6 screws, 6 lock washers and 6 nuts)
Click on photo for
larger view
Marshall™
MEDIUM BRASS ROUND-HEAD SCREWS WITH LOCK WASHERS AND NUTS (SET OF 8). Set
of 8 screws, brass, 3/8" (12.7mm) long, slotted round head - head is 6.1mm in diameter,
6-32
thread, with lock washer and nut. Used to mount power tube sockets,
capacitor cans and ground lugs in classic Marshall™
amps.
Part #MMBS-8
$2.99
(for a pack of 8 screws, 8 lock washers and 8 nuts)
Click on photo for
larger view
REPLACEMENT
HOUSING SCREWS FOR MXR™ PEDALS (MODERN VERSION)
Set of 4
housing screws for MXR™, Way Huge and
other pedals which use 6-32 x 1/2" screws, including pedals which use Bud or
Hammond style enclosures.
Replacement
screws for Dunlop™ DCB10 DC Brick, MXR™ M101 Phase 90, MXR™ M102 Dyna Comp,
MXR™
M103 Blue Box, MXR™ M104 Distortion+, MXR™ M115 Distortion III, MXR™ M132
SuperComp, MXR™ M133 Micro Amp, MXR™ M134 Stereo Chorus, MXR™ M169 Carbon Copy
Analog Delay, MXR™ M173 Classic 108 Fuzz, MXR™ M182 El Grande Bass Fuzz,
MXR™
MC401 Custom Audio Electronics Boost, MXR™ MC402 Boost Overdrive, Dunlop™ ZW44 Zakk Wylde Overdrive and others.
Part #D-ECB-590
$0.59
(for a set of 4 screws)
Click on photo for
larger view
REPLACEMENT
HOUSING 3/8" SCREWS FOR MXR™ PEDALS (VINTAGE VERSION)
Set of 4 housing screws for MXR™, Way Huge and
other pedals which use 6-32 x 3/8" screws, including pedals which use Bud or
Hammond style enclosures.
Early MXR™
pedals (1972-1987) require a 3/8" screw to attach the bottom cover.
The D-ECB-590 screw is too long for the vintage MXR pdeals.
Part #D-ECB-589
$0.59
(for a set of 4 screws)
Click on photo for
larger view
FENDER™SPEAKER MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 12. Locking
nut and washer included. Phillips head. Drill hole, insert and
tighten screws into wood from front of baffle. Install grill cloth, and
you have professional speaker mounting studs. Replacement for
original Fender™ speaker mounting studs. Fender™ part number
0992094000. Set of 12.
Part #SC-409-12
$14.95
(For a pack of 12 screws with nuts and lock washers)
Click on photo for
larger view
FENDER™SPEAKER MOUNTING SCREW WITH BOTH WOOD AND MACHINE THREADS, SET OF 4. Locking
nut and washer included. Phillips head. Drill hole, insert and
tighten screws into wood from front of baffle. Install grill cloth, and
you have professional speaker mounting studs. Replacement for
original Fender™ speaker mounting studs. Fender™ part number
0992094000. Set of 4.
Part #SC-409-4
$3.99
(For a pack of 4 screws with nuts and lock washers)
Click on photo for
larger view
ISOLATION WASHER - 3/8" - For #8 Screws
3/8" outside diameter neoprene bonded flat washer. Perfect for
bolting speakers to cabinets. It will securely hold the speaker in place and
stop any rattling. For use with #8 screws. Ideal for vintage Fender
amps with #8 speaker mounting screws. Set of 4 washers.
Part #SIW-38-4
$0.59
(For a set of 4 washers)
Click on photo for
larger view
ISOLATION WASHER - 1/2" - For #10 Screws
Larger 1/2" outside diameter neoprene bonded flat washer. Perfect for
bolting speakers to cabinets. It will securely hold the speaker in place and
stop any rattling. For use with #10 screws, such as a 10-32 machine screw. Set of 4 washers.
Part #SIW-50-4
$0.69
(For a set of 4 washers)
Click on photo for
larger view
REPLACEMENT
HOUSING SCREWS FOR MXR PEDALS
Set of 4 housing screws for MXR, Way Huge and
other pedals which use 6-32 x 1/2" screws, including pedals which use Bud or
Hammond style enclosures.
Replacement
screws for Dunlop DCB10 DC Brick, MXR M101 Phase 90, MXR M102 Dyna Comp, MXR
M103 Blue Box, MXR M104 Distortion+, MXR M115 Distortion III, MXR M132
SuperComp, MXR M133 Micro Amp, MXR M134 Stereo Chorus, MXR M169 Carbon Copy
Analog Delay, MXR M173 Classic 108 Fuzz, MXR M182 El Grande Bass Fuzz, MXR
MC401 Custom Audio Electronics Boost, MXR MC402 Boost Overdrive, Dunlop ZW44
Zakk Wylde Overdrive and others.
Part #D-ECB590
$0.59
(for a set of 4 screws)
Click on photo for
larger view
Fender™ SELF-TAPPING SCREWS
Used in vintage Fender™ blackface and silverface
amps for a variety of
tasks. Used to attach capacitor pans, tube sockets, transformers on smaller amps, chokes, etc.
Pack of 12 screws. Replaces Fender™ part number 029913. Part #SC-410-12
$3.50
(for a pack of 12 screws)
Click on photo for
larger view
SELF-TAPPING
#6 SCREWS #6 x ⅜ zinc type AB.
Type AB screws tap their own mating internal thread. They require a preformed
hole for installation into metallic materials but not necessary for wood or
plastic materials. Screws have a point at the end of the threads.
Pack of 5 screws. Part #SC-238-5
$0.99
(for a pack of 5 screws)
Click on photo for
larger view
Fender™ "DOGBONE" HANDLE SCREWS
Pack of 4
nickel "Dogbone" handle screws for Fender™
style FAH-328 and FAH-329 handles. 8-32 thread. Fits the handle on the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, and Blues Deville, as well as other Fender™ amps of similar design. Also
works with Hiwatt and Vox™ handles and other British design amp handles. Part #SC-402
$1.59
(for a pack of 4 screws)
Click on photo for
larger view
10-32 THREAD HANDLE SCREWS
Pack of 4 stainless steel handle screws for
handles which require 4 screws. 1" Long, 10-32 threads. Designed
to work with a 10-32 T-Nut, in cabinet wood of 3/4" or less.
Will not work with external nut - must be a T-Nut. Will not work
with cabinet wood thicker than 3/4".
See Data Sheet here Part #SC-403-4
$1.95
(for a pack of 4 screws)
Click on photo for
larger view
Fender™ VINTAGE HANDLE SCREWS
Pack of 2 stainless steel handle screws for Fender™
style FAH-332, FAH-261 handle. 1" Long, 10-32 threads. Designed
to work with a 10-32 T-Nut, in cabinet wood of 3/4" or less.
Will not work with external nut - must be a T-Nut. Will not work
with cabinet wood thicker than 3/4".
See Data Sheet here Part #SC-403
$0.99
(for a pack of 2 screws)
Click on photo for
larger view
Fender™
EXTRA LONG VINTAGE HANDLE SCREWS
Pack of 2 stainless steel extra long handle screws for Fender™
style FAH-332, FAH-261 handle. Used for vintage Fender™ style strap
handles used on speaker cabinets, such as Bandmaster, Bassman, Showman,
and Blonde or Blackface Tremolux. 1-1/4" Long, 10-32 threads. Designed
to work with a 10-32 T-Nut, in cabinet wood of 1-1/8" or less.
Will not work with external nut - must be a T-Nut. Will not work
with cabinet wood thicker than 1-1/8".
See Data Sheet here Part #SC-403A
$0.99
(for a pack of 2 screws)
Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS
(SET OF 28) FOR CLOSED BACK CABINETS (SUCH AS Fender™ BASSMAN 2x12, BANDMASTER
2x12, etc). Set
of 28 #8 screws, Stainless Steel, 1 3/4" long, Phillips, oval head. Use with the
CW-400-28 cup washers. A set of 28 screws completely replaces
all of the screws on most vintage Bassman™ 2x12 and Bandmaster™ 2x12 cabinets
Part #SC-400-28
$5.69
(for a pack of 28 screws)
Click on photo for
larger view
BACK PANEL STAINLESS STEEL SCREWS
(SET OF 28) FOR CLOSED BACK CABINETS (SUCH AS Fender™ BASSMAN 2x15). Set
of 36 #8 screws, Stainless Steel, 1 3/4" long, Phillips, oval head. Use with the
CW-400-36 cup washers. A set of 36 screws completely replaces
all of the screws on most vintage Bassman™ 2x15 cabinets.
Part #SC-400-36
$6.99
(for a pack of 36 screws)
Click on photo for
larger view
BLACK HANDLE SCREWS
Pack of 2 stainless-steel handle screws finished
in satin black for use
with black end-cap handles, such as our GAH-1 or GAH-271B. 1-1/4" Long, 10-32 threads, finished in satin black to match black end caps. Designed
to work with a 10-32 T-Nut, in cabinet wood of 3/4" or less.
Will not work with external nut - must be a T-Nut. Will not work
with cabinet wood thicker than 3/4".
See Data Sheet here Part #SC-403B
$0.99
(for a pack of 2 screws)
Click on photo for
larger view
GUITAR PICKGUARD SCREWS, CHROME. Set of 12 chrome screws for
electric guitar pickguards.
Part #PGSC-12
$2.49
(pack of 12 screws)
Click on photo for
larger view
GUITAR PICKGUARD SCREWS, BLACK. Set of 12 black screws for
electric guitar pickguards.
Part #PGSB-12
$2.49
(pack of 12 screws)
Click on photo for
larger view
Fender™ Style Stainless Steel Corner Screws, Set of
8 Oval-head Phillips corner screws for counter-sunk amp corners,
such as the FVC-2L and FVC-3 Fender™ corners. 3/4 inches long, Phillips head,
stainless steel for long rust-free life. Set
of 8 screws, for four FVC-2L corners.
Part #SC-406-8
$2.99
(for a pack of 8 screws)
Click on photo for
larger view
Fender™ Style Stainless Steel Corner Screws, Set of
12
Oval-head Phillips corner screws for counter-sunk amp corners,
such as the FVC-2L and FVC-3 Fender™ corners. 3/4 inches long, Phillips head,
stainless steel for long rust-free life. Set
of 12 screws, for four FVC-3 corners.
Part #SC-406-12
$4.29
(for a pack of 12 screws)
Click on photo for
larger view
Nickel-plated Truss-Head Corner Screws
Flat pan type truss-head corner screws for NON counter-sunk
nickel corners,
such as our NPC-157-2, NPC-157-2L and NPC-157-3 corners. 1/2 inch long,
Phillips head, nickel plated. Sold individually.
Part #SC-225
$0.39
(each)
Click on photo for
larger view
Black Truss-Head Corner Screws
Flat pan type black truss-head corner screws for NON counter-sunk
black corners,
such as our SCC-130-2, SCC-130-2L and SCC-130-3 corners. 1/2 inch long,
Phillips head, black powder coated. Sold individually.
Part #SC-304
$0.35
(each)
Click on photo for
larger view
STAINLESS STEEL CHASSIS SCREWS WITH WASHERS, Marshall™ METRIC Replacements for the standard M6 metric screws used to hold the chassis in
virtually every Marshall™ head. Washers included. Package of 4
stainless steel screws, with 4 washers. Part #MCB-4
$3.99
(Set of 4 screws w/washers)
Click on photo for
larger view
STAINLESS STEEL
CHASSIS SCREWS, 10-24 THREAD, SET OF 4
SCREWS. These 10-24 screws are used on a limited number of amplifiers as chassis
mounting screws. Oval head, 1-1/2 inches long, stainless steel,
10-24 thread. Set of 4 screws. Generally used with the extra-large CW-502 cup
washer. Part #SC-412-4
$1.99
(Set of 4 screws)
Click on photo for
larger view
BLACK PAN-HEAD WOOD SCREWS, #6 X 3/4", PACK OF 10. Deep
threads, sharp point, pan head with Philips drive. #6 screw, 3/4 inch
long, pack of 10.
Part #SCR-435
$0.79
(pack of 10)
BLACK PAN-HEAD WOOD SCREWS, #8 X 1/2", PACK OF 10. Deep
threads, sharp point, pan head with Philips drive. #8 screw, 1/2 inch
long, pack of 10.
Part #BWS8-5
$0.99
(pack of 10)
BLACK PAN-HEAD WOOD SCREWS, #8 X 3/4", PACK OF 10. Deep
threads, sharp point, pan head with Philips drive. #8 screw, 3/4 inch
long, pack of 10.
Part #BWS8-75
$1.10
(pack of 10)
BLACK PAN-HEAD WOOD SCREWS, #8 X 1", PACK OF 10. Deep
threads, sharp point, pan head with Philips drive. #8 screw, 1 inch long,
pack of 10.
Part #BWS8-1
$1.25
(pack of 10)
BLACK PAN-HEAD WOOD SCREWS, #8 X 1 1/2", PACK OF 10.
Deep threads, sharp point, pan head with Philips drive. #8 screw, 1-1/2
inches long, pack of 10.
Part #BWS8-15
$1.39
(pack of 10)
Click on photo for
larger view
STAINLESS STEEL
COMBO CHASSIS SCREWS, Marshall™ METRIC (NOT BLACK!) SET OF 4
SCREWS. Unpainted replacements for the standard M6 metric screws used to hold the chassis in virtually every
larger Marshall™
combo (typically 50 watts & up). Note that these
screws are plain stainless steel - NOT BLACK LIKE THE ORIGINALS. You may paint the top
black if you choose. We recommend that you only paint the top - do not
paint the threads. 35mm long, replaces Marshall part number MESCRW00001.
Found in the JTM610, JTM612, JTM612, JTM615, JTM622, JCM601, JCM602, 2101, 2501,
2502, 4101, 4102, 4501, 4502, TSL601, TSL601, and TSL122. Set of 4 screws.
See the CW-400-4 washer set below for suitable washers. Part #MCS-5140-4
$2.29
(Set of 4 screws)
Click on photo for
larger view
CUP WASHER, STAINLESS STEEL, LARGE, SET OF 4. OD 1/2", ID 3/16"
Typically found on larger combo amp cabinets and 4x12 cabinets, such as
Marshall™ . Set of 4 washers.
Part #CW-400-4
$0.99
(for a set of 4 washers)
Click on photo for
larger view
STAINLESS STEEL CHASSIS SCREWS WITH WASHERS,
Orange™ METRIC Replacements for the standard M6-1.00 50mm metric screws used to hold the chassis in
UK-built Orange™ heads and combos. Washers
included. Package of 4 stainless steel screws, with 4 washers. Part #OCB-4
$4.99
(Set of 4 screws w/washers)
Click on photo for
larger view
STAINLESS STEEL CHASSIS SCREWS WITH WASHERS,
Trace Elliot™ METRIC Replacements for the standard M6-1.00 35mm metric screws used to hold the chassis in
UK-built Trace Elliot™ heads and combos. Washers
included. Package of 4 zinc-plated steel screws, with 4 washers. Part #TCB-4
$3.99
(Set of 4 screws w/washers)
Click on photo for
larger view
Hex footswitch nut, pack of
4
These replacement nuts fit all
Carling™
brand footswitches and toggle switch and some (but not
all) other switches which are not made by Carling™.
Carling™
toggle switches are used in Fender™
amps. Hex outer
surface (9/16"), M12 thread for 15/32" bushing.
Part HFN-4
$0.99
(for a pack of 4 nuts)
Click on photo for
larger view
SAVE WITH MULTIPACK!
JNUT-38 JACK NUT AND WASHER, METAL,
SWITCHCRAFT™, SET OF 6 Genuine Switchcraft™ nut and washer set for the blackface/silverface Fender™ bias pot, Mesa Boogie pots, and the
CTS or Alpha pots with 3/8" bushing (found on original vintage Fender™
blackface and silverface), as well as Peavey™ and Switchcraft™
1/4" jacks. Does NOT fit the 24mm Marshall™ pots. Set of
6 washers and 6 nuts. Part #JNUT-38-6
$4.50
(Set of 6 washers and 6 nuts)
Click on photo for
larger view
JACK NUT AND WASHER, METAL,
SWITCHCRAFT™ Genuine Switchcraft™ nut and washer set for the blackface/silverface Fender™ bias pot, Mesa Boogie pots, and the
CTS or Alpha pots with 3/8" bushing (found on original vintage Fender™
blackface and silverface), as well as Peavey™ and Switchcraft™
1/4" jacks. Does NOT fit the 24mm Marshall™ pots. Part #JNUT-38
$0.89
(Set of 1 washer and 1 nut)
NUT AND WASHER, NICKEL, KOBICONN
OR JALCO TYPE. Fits J-506, J-506A, J-507, J-530, J-531
, J-532, J-533, J-533G,
J-539, J-539G, J-540, J-545, J-6074, J-6075, J-560. Part #JN-916
$0.75
Click on photo for
larger view
NUT, NICKEL, REAN TYPE, Fender™, AMPS 1999 - Present. Fender™ nut, fits J-508 and J-509 jacks. (Note: you can use this nut on the Cliff J-502, J-503, J-504, J-505, J-503L and J-504L jacks as well, if you wish to change your amps appearance.) Part #J-510
$ 0.85
Click on photo for
larger view
WASHER, FOR BRITISH STYLE (CLIFF) JACKS. This washer goes behind the faceplate on British style plastic nut and
chrome nut jacks to provide proper spacing. Jacks come with the
washers included, but the washers are easily lost. Without the washers,
the jacks will not fit properly. Part #W-583
$0.18
for each washer.
(Jacks not included).
Click on photo for
larger view
JACK NUT, PLASTIC, BRITISH STYLE, REPLACEMENT FOR Marshall™ AND OTHERS.
Note: Replaces most black plastic jack nuts EXCEPT for
Roland. Will NOT fit Roland jacks.
Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and
J-504L jacks. Also fits the J-518 and J-519 jacks. Part #J-5NT
$0.50
Click on photo for
larger view
JACK NUT MULTI-PACK - SAVE!
6 JACK NUTS, PLASTIC, BRITISH STYLE, REPLACEMENT FOR Marshall™ AND OTHERS.
Note: Replaces most black plastic jack nuts EXCEPT for
Roland. Will NOT fit Roland jacks. Replacement jack nut as found on the J-502, J-503, J-504, J-505, J-503L and
J-504L jacks. Also fits the J-518 and J-519 jacks. Part #J-5NT-6
$2.39
Click on photo for
larger view
JACK NUT, PLASTIC,
BRITISH STYLE, RED
Replacement nut for the J-503, J-504.
Red nuts on these jacks typically are used on later model Marshall™ amps to
designate the 'speaker' jacks. Part #J-5NTR
$1.00
Click on photo for
larger view
JACK NUT, PLASTIC, BRITISH STYLE, WHITE
Replacement nut for the J-555 and J-556 jacks.
Will also fit the J-502, J-503, J-504, J-505, J-503L and J-504L black jacks, if you wish to create a two-tone effect. Part #J-5NTW
$1.00
Click on photo for
larger view
JACK
NUT/FERULE, CHROME, with BLACK PLASTIC BEZEL/WASHER - BRITISH CLIFF STYLE Replacement nut and bezel washer for the J-501, J-501S, J-580, J-581, J-580L and J-581L jacks.
Note: The threads on this nut are coarse (3/8-20), and are for
genuine Cliff jacks. Note:
There are some generic jacks on the
market with finer thread nuts.
This nut will not fit those jacks. This nut is for
BRITISH CLIFF STYLE jacks. Bezel is
included with this nut. Part #JN-200W
$0.95
Click on photo for
larger view
JACK
NUT/FERULE, BLACK, with INTEGRAL BLACK PLASTIC BEZEL - BRITISH STYLE Replacement nut and bezel washer which will fit the J-501, J-501S, J-580, J-581, J-580L,
and J-581L jacks.
Note: The threads on this nut are coarse (3/8-20), and are for
genuine Cliff UK jacks. Note:
There are some generic jacks on the
market with finer thread nuts.
This nut will not fit those jacks. This nut is for
genuine Cliff UK jacks. Bezel is integral to the nut and cannot be
removed. This is the jack nut used on the Marshall JMP-1 Preamp, and
on some versions of the Marshall DRP-1 Direct Recording Preamp. Part #JN-864
$0.89
Click on photo for
larger view
KEPS NUT, ZINC, 6-32
THREAD, SET OF 4 NUTS. Typically used on Fender™ speaker baffle
mounting on vintage and reissue "tweed" amps.
Works with all
6-32 screws.
Captive lock washer keeps nut tight. Zinc coating retards oxidation.
Sold in a pack of 4. Part NT-632-4
$0.59
(pack of 4 nuts)
Click on photo for
larger view
KEPS NUT, ZINC, 8-32
THREAD, SET OF 4 NUTS. Typically used on Fender™ Nickel Chassis Straps bolts, and for
speaker mounting.
Works with all 8-32 screws.
Captive lock washer keeps nut tight. Zinc coating retards oxidation.
Sold in a pack of 4. Part NT-832-4
$0.69
(pack of 4 nuts)
Click on photo for
larger view
KEPS NUT, ZINC, 10-32
THREAD, SET OF 4 NUTS. Typically used on Fender™ chassis
mounting screws on vintage "tweed" amps from the 1950s.
Works with all
10-32 screws.
Captive lock washer keeps nut tight. Zinc coating retards oxidation.
Sold in a pack of 4. Part NT-1032-4
$0.79
(pack of 4 nuts)
Click on photo for
larger view
Premium-quality steel T-nuts feature
three razor-sharp teeth
and 8-32 fine thread. Works with all 8-32 screws - recommended for mounting
many guitar amp handles. Pack of 4 nuts.
Part TNUT-832
99 cents
(pack of 4)
Click on photo for
larger view
Premium-quality steel T-nuts feature six razor-sharp teeth and extra-long barrels.
1/4"-20 coarse thread.
The result is a T-nut that goes in straighter and holds tighter than ordinary T-nuts. As a bonus, the 6-prong design ensures that your T-nut will stay in place even when working at the edge of a driver hole. We guarantee that these are the finest T-nuts that you will find on the market. Recommended hole size is 1/4", thread is 10-32,
barrel length is 11mm, or about 7/16". Pack of 4 nuts.
Part 6-TNUT-1032
$1.59
(pack of 4)
Click on photo for
larger view
Premium-quality steel T-nuts feature six razor-sharp teeth and extra-long barrels.
1/4-20 thread.
The result is a T-nut that goes in straighter and holds tighter than ordinary T-nuts. As a bonus, the 6-prong design ensures that your T-nut will stay in place even when working at the edge of a driver hole. We guarantee that these are the finest T-nuts that you will find on the market. Recommended hole size is
5/16", thread is 1/4-20,
barrel length is 17/32", or about 13.5mm. Pack of 4 nuts.
Part 6-TNUT-1/4-20
$1.59
(pack of 4)
Click on photo for
larger view
Marshall™ CHASSIS WASHERS Replacements for the standard washers used with the MCB-4 chassis screws under virtually every Marshall™
head. Note: Not for Marshall Combo amps.
Also fits Orange and Trace Elliot amps which use chassis bolts to secure the
chassis. Package of 4 washers. Part #MCW-4
$1.99
(Set of 4 washers)
Click on photo for
larger view
CHASSIS CAGE NUTS, Marshall™ M6 METRIC Replacements for the standard M6 metric cage nuts used on the chassis in virtually every Marshall™ head. Package of 4 cage nuts. Mates with the MCB-4
or MCS-5140-4 screws, above. Part #MCN-4
$4.59
(Set of 4 nuts)
Click on photo for
larger view
CAGE NUT, ZINC, 10-32
THREAD. Used on square-punched amp chassis rails to secure the
chassis to the cabinet. Frequently found in Peavey, Crate, Ampeg,
other brands. NOT used in Marshall™ - see the MCN-4.
Works with all
10-32 screws.
Verify screw thread before ordering, as not all cage nuts are 10-32. Zinc coating retards oxidation.
Pack of 4 nuts. Made in Canada by Hammond Industries. Part CNA-1421
$4.29
(pack of 4)
Click on photo for
larger view
Ground Lug Terminals - Angled Made from tin-plated brass - will not rust. Used to connect a ground wire to a screw and nut on a chassis.
Angled,
with two holes for soldering wires. With built-in lock washer to keep the screw
and nut from loosening. Designed for a #8 size screw.
Pack of 5 terminals. Part #GL-113
$1.39
(Pack of 5 terminals)
Click on photo for
larger view
TERMINAL STRIPS, 6 LUG, SET OF
2. Perfect for amplifier circuit additions or modifications.
Center post for mounting to chassis. All 6 terminals are isolated
from ground. Each terminal strip is 2-5/8 inches
long. The lugs are set on 3/8 inch centers. Each lug
will accept wires up to 16ga - smaller gauge allows multiple wires to be
connected to each lug. Set contains 2 terminal strips as pictured.
Mounting hardware not included. Part #TS-825
$2.99
(for a set of 2 terminal strips)
Click on photo for
larger view
TERMINAL STRIPS, 7 LUG, SET OF
2. Perfect for amplifier circuit additions or modifications.
End terminals on each strip are the mounting lugs, so they become a ground lug
if attached to a metal chassis. Each terminal strip is 2-5/8 inches
long. The lugs are set on 3/8 inch centers. Each lug
will accept wires up to 16ga - smaller gauge allows multiple wires to be
connected to each lug. Set contains 2 terminal strips as pictured.
Mounting hardware not included. Part #TS-712
$3.69
(for a set of 2 terminal strips)
Click on photo for
larger view
PC BOARD STANDOFF, NYLON, MARSHALL STYLE This
style of PC board standoff is used in a number of amplifiers. Designed for
a 4.5mm hole in the chassis, and a 2.5mm hole in the PC board. Total
height of standoff is 26.3mm (just over 1 inch). Supports the PC
board at a height of 15.8mm (5/8 inch) above the chassis. Set of 4
standoffs in the kit.
Part #PCS-15
$1.99
(for a set of 4 standoffs)
Click on photo for
larger view
Fender™ Style Pop-Out 2" Caster Wheels - Set
of 4.
Great for Fender™ and many other brands of amps or cabinets. Each
wheel capable
supporting 45 lbs, or 180 lbs total for the set of 4. Wheels 2" in
diameter. The same type of removable caster wheels used on Fender™ amps
since the 1960s. Note:
Mounting screws NOT included. Must drill 5/8" hole in bottom of
cabinet to accommodate post for wheel. Part #FCW-4R
$30.95
(Set of 4 pop-out casters)
NOT SOLD OUTSIDE the USA
Click on photo for
larger view
Fender™ Style Flat Mount 2" Caster Wheels - Set
of 4.
Great for Fender™ and many other brands of amps or cabinets. Each
wheel capable of supporting 45 lbs, or 180 lbs total for the set of 4.
Wheels 2" in diameter. Specifications found
here. Note:
Mounting screws NOT included. Part #FCW-4F
$30.95
(Set of 4 casters)
NOT SOLD OUTSIDE the USA
Click on photo for
larger view
Vintage Fender™ Style Blackface and Silverface 2-Leg Wrap-Around Cabinet Corner
with Lip - Bright Nickel Plated Steel
(Not designed for the Blackface or Silverface REISSUES. NOT for
vintage Fender™ Speaker Cabinets or Heads, such as Bassman, Bandmaster, Showman,
Tremolux, etc. These corners fit most vintage Fender combo amps.)
Vintage style Fender™ corners with
counter-sunk screw holes. For 1/2" radius corners. Set of
4, includes oval-head tapered stainless screws. Part #FVC-2L
$7.50
(Set of 4 corners with screws)
Click on photo for
larger view
Vintage Fender™ Style Blackface and
Silverface 2-Leg Wrap-Around Cabinet Corner with Lip - Bright Nickel Plated
Steel
(Not designed for the Blackface or Silverface
REISSUES. NOT for vintage Fender™ Speaker Cabinets or Heads,
such as Bassman, Bandmaster, Showman, Tremolux, etc. These corners fit
most vintage Fender combo amps.)
Recreation of the vintage Fender™ corners
with counter-sunk screw holes. For 1/2" radius corners.
Set of 2, includes oval-head tapered stainless screws. Part
#FVC-2L-2
$3.75
(Set of 2 corners with screws)
Click on photo for
larger view
Vintage Fender™ Style 3-Leg Corners with
counter-sunk screw holes, set of 2. Bright nickel-plated steel. Recreation of the vintage
style corners with
counter-sunk screw holes from the 60s and 70s.
These
corners have 3 legs (two long, one short), for 1/2" radius corners with solid
material on all three sides (no recesses). Typically used as the
rear bottom corners on the Fender Bassman Ten Combo, the Deluxe 112, etc. Set of 2, includes oval-head
tapered stainless screws.
Part #FVC-3
$3.50
(Set of 2 corners with screws)
Click on photo for
larger view
Vintage Fender™ Style 2-Leg and 3-Leg Corners with
counter-sunk screw holes. Bright nickel-plated steel.
Recreation of the vintage style corners with counter-sunk screw holes from
the 60s and 70s. Two FVC-2L type corners with two legs and a lip, and
two FVC-3 corners with three legs. Typically used around the bottom of the
Bassman Ten (or Bassman 10) Combo Amp from 1972 to 1982. Set of 4
corners total - two FVC-2L for the front, and two FVC-3 for the back. Includes oval-head
tapered stainless screws.
Part #FVC-23
$6.50
(Set of 4 corners with screws)
Click on photo for
larger view
Fender™ Style Stainless Steel Corner Screws, Set of
8 Oval-head Phillips corner screws for counter-sunk amp corners,
such as the FVC-2L and FVC-3 Fender™ corners. 3/4 inches long, Phillips head,
stainless steel for long rust-free life. Set
of 8 screws, for four FVC-2L corners.
Part #SC-406-8
$2.99
(for a pack of 8 screws)
Click on photo for
larger view
Fender™ Style Stainless Steel Corner Screws, Set of
12
Oval-head Phillips corner screws for counter-sunk amp corners,
such as the FVC-2L and FVC-3 Fender™ corners. 3/4 inches long, Phillips head,
stainless steel for long rust-free life. Set
of 12 screws, for four FVC-3 corners.
Part #SC-406-12
$4.29
(for a pack of 12 screws)
Click on photo for
larger view
Black Oval-Head Corner Screws, Set of
8 Black oval-head Phillips corner screws for counter-sunk amp corners.
Works with Vox black plastic corners, and Fender style black metal corners with
recessed screw holes. #6 x 3/4 inches long, Phillips head,
black oxide. Screws are beveled under the head for use in countersunk
holes. Length measured from the edge of the head to tip of the
screw. Set
of 8 screws. Part #SC-411-8
$1.50
(For a set of 8 black oval-head Phillips screws)
Click on photo for
larger view
Revisit™
Metal 2-Leg Cabinet Corner Black Durable powder-coated steel corners provide
protection and a finished look for small to medium sized speaker cabinets
and racks. Two legs, one edge is cut-away, for use on front of
cabinet with any thickness of wood from 1/2" and larger. Dimensions: 1.6" H x 1.6" W x 0.5" D. Set of
4 corners. Screws not included - recommend the SC-304 truss-head
screws for use with these corners. Part #SCC-130-2
$4.99
(Set of 4 corners)
Click on photo for
larger view
Revisit™
Metal 2-Leg Wrap-Around Cabinet Corner
with Lip - Black Durable black-finished steel corners provide
protection and a finished look for small to medium sized speaker cabinets
and racks. Cabinet corner, wrap-around style that suits 3/4" wood with vinyl
or paint covering, 2 leg • Dimensions: 1.42" x 0.87" • Metal thickness: 0.9
mm/.035" Set of
4 corners. Screws not included - recommend the SC-304 truss-head
screws for use with these corners. Part #SCC-130-2L
$4.99
(Set of 4 corners)
Click on photo for
larger view
Revisit™
Metal 3-Leg Cabinet Corner Black Durable powder-coated steel corners provide
protection and a finished look for small to medium sized speaker cabinets
and racks. Dimensions: 1.6" H x 1.6" W x 1.6""D.
Set of 4 corners. Screws not included - recommend the SC-304
truss-head screws for use with these corners. Part #SCC-130-3
$4.99
(Set of 4 corners)
Click on photo for
larger view
Revisit™
Black Truss-Head Corner Screws
Flat pan type black truss-head corner screws for NON counter-sunk
black corners,
such as our SCC-130-2, SCC-130-2L and SCC-130-3 corners. 1/2 inch long,
Phillips head, black powder coated. Sold individually.
Part #SC-304
$0.20
(each)
Click on photo for
larger view
Revisit™
Metal 2-Leg Cabinet Corner Nickel Plated
Steel Durable nickel-plated steel corners provide
protection and a finished look for small to medium sized speaker cabinets
and racks. Two legs, one edge is cut-away, for use on front of cabinet
with any thickness of wood from 1/2" and larger. Dimensions: 1.6" H x 1.6" W x 0.5" D. Set of
4 corners. Screws not included - recommend the SC-225 truss-head
screws for use with these corners. Part #NPC-157-2
$5.95
(Set of 4 corners)
Click on photo for
larger view
Revisit™
Metal 2-Leg Wrap-Around Cabinet Corner
with Lip - Nickel Plated Steel Durable nickel-plated steel corners provide
protection and a finished look for small to medium sized speaker cabinets
and racks. Cabinet corner, wrap-around style that suits 3/4" wood with vinyl
or paint covering, 2 leg • Dimensions: 1.42" x 0.87" • Metal thickness: 0.9
mm/.035" Set of
4 corners. Screws not included - recommend the SC-225
truss-head screws for use with these corners. Part #NPC-157-2L
$5.95
(Set of 4 corners)
Click on photo for
larger view
Revisit™
Metal 3-Leg Cabinet Corner Nickel Plated
Steel Durable nickel-plated steel corners provide
protection and a finished look for small to medium sized speaker cabinets
and racks. Dimensions: 1.6" H x 1.6" W x 1.6"" D.
Set of 4 corners. Screws not included - recommend the
SC-225 truss-head screws for use with these corners. Part #NPC-157-3
$5.95
(Set of 4 corners)
Click on photo for
larger view
Revisit™
Nickel-plated Truss-Head Corner Screws
Flat pan type truss-head corner screws for NON counter-sunk
nickel corners,
such as our NPC-157-2, NPC-157-2L and NPC-157-3 corners. 1/2 inch long,
Phillips head, nickel plated. Sold individually.
Part #SC-225
$0.20
(each)
Click on photo for
larger view
Revisit™
Black Plastic Stacking Corners - Set of 4
corners For speaker cabinets and cases.
Popular "chevron" angled ridges for interlocked stacking. Screws not included - recommend the
SC-411-8 black screws for use with these corners (two packs of SC-411-8
screws needed per set of 4 corners.) Part #BPC-834
$2.99
(Set of 4 corners)
ONLY 1 SET LEFT!
DISCONTINUED!
Click on photo for
larger view
Vox™
CORNER, BLACK PLASTIC, SOLD INDIVIDUALLY. These
Tube Amp Doctor black plastic corners are great replacements for Vox™ and
Orange™ amps and cabinets that feature this type. The two larger holes are for
use with screws while the small holes are intended for pins/nails just like the
originals. 3/4" radius, 2 pins on front.
Used on some vintage
Vox™
amps. For heads, combos and straight speaker cabinets.
Screws NOT included. Part #VC-1050
$2.45
(Per individual corner)
Click on photo for
larger view
Black Oval-Head Corner Screws, Set of
8 Black oval-head Phillips corner screws for counter-sunk amp corners.
Works with Vox or Orange black plastic corners. #6 x 3/4 inches long, Phillips head,
black oxide. Screws are beveled under the head for use in countersunk
holes. Length measured from the edge of the head to tip of the
screw. Set
of 8 screws. Part #SC-411-8
$1.50
(For a set of 8 black oval-head Phillips screws)
Click on photo for
larger view
Marshall™ CORNERS, FRONT OF
CABINET
Front corner set, ¾" radius. Includes 12
gold rivets for attaching to cabinet. For heads, combos and straight
speaker cabinets. Will not fit slanted speaker cabinets,
such as the 1960A. For slanted cabinets, see the MC-1092 set.
Part #MC-1091
$10.95
(For a set of 4 corners with 12 rivets)
Under new ownership (Zounds, Inc. of Sweden), Marshall is currently not shipping
parts. See the RC-1091 as a substitute set of corners.
Click on photo for
larger view
Revisit™
Quality Reproduction of Marshall™ CORNERS, FRONT OF
CABINET
Front corner set, ¾" radius. Includes 12
gold rivets for attaching to cabinet. For
Marshall™
heads, combos and straight
speaker cabinets. Replace your
Marshall™
corners with quality parts at 25% less than Marshall™
prices.
Will not fit slanted speaker cabinets,
such as the 1960A. For slanted cabinets, see the MC-1092 set.
Part #RC-1091
$7.95
(For a set of 4 corners with 12 rivets)
Click on photo for
larger view
Marshall™
SPECIAL CORNERS, FRONT OF
SLANTED SPEAKER CABINETS
Front corner set, ¾" radius. Includes 12
gold rivets for attaching to cabinet. Two top angled corners for the
left and right top corners of angled speaker cabinets, and two straight corners for the bottom front
corners. For slanted speaker cabinets ONLY,
such as the 1960A, MG412AG, MX412A Part #MC-1092
$16.95
(For a set of 4 corners with 12 rivets)
Under new ownership (Zounds, Inc. of Sweden), Marshall is currently not shipping
parts.
Click on photo for
larger view
Marshall™ CORNERS, REAR OF
CABINET
Rear corner set, ¾" radius. Includes 16
gold rivets for attaching to cabinet. For heads, combos and speaker
cabinets.
Part #MC-1090
$11.95
(For a set of 4 corners with 16 rivets)
Under new ownership (Zounds, Inc. of Sweden), Marshall is currently not shipping
parts. See the RC-1090 as a substitute set of corners.
Click on photo for
larger view
Revisit™
Quality Reproduction of Marshall™ Corners, Rear of
Cabinet
Rear corner set, 3/4" radius. Includes
16
gold rivets for attaching to cabinet. For Marshall™
heads, combos and
speaker cabinets. Replace your
Marshall™
corners with quality parts at 25% less than Marshall™
prices.
Part #RC-1090
$8.95
(For a set of 4 rear corners with 16 rivets)
Click on photo for
larger view
Marshall™
GOLD RIVETS
For attaching Marshall™ corners to cabinets. Gold, package of 12 rivets. Part #MR-109
$4.95
(For a set of 12 gold rivets)
Click on photo for
larger view
Marshall™
SILVER RIVETS
For attaching Marshall™ corners to cabinets. Silver, package of 12 rivets. Part #MR-109S
$4.95
(For a set of 12 silver rivets)
Click on photo for
larger view
Black Oval-Head Corner Screws, Set of
8 Black oval-head Phillips corner screws for counter-sunk amp corners.
Works with Vox black plastic corners. #6 x 3/4 inches long, Phillips head,
black oxide. Screws are beveled under the head for use in countersunk
holes. Length measured from the edge of the head to tip of the
screw. Set
of 8 screws. Part #SC-411-8
$1.50
(For a set of 8 black oval-head Phillips screws)
Click on photo for
larger view
Revisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, BLACK WITH
BLACK STITCHING
Good replacement for Ampeg, Mesa Boogie, Randall™, Bogner, Ashdown, Rivera,
Blackstar, many others. Handle
length is 8-9/16 inches (8.57"), center-to-center mounting distance is 7-3/8
inches (7.38") Black with black stitching, nickel mounts.
More details Mounting
screws not included - use SC-402 or SC-403-4 screw pack. Part #AH-281
$23.95
"SHORTY" AMP HANDLE
Click on photo for
larger view
Revisit™
"SHORTY" AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, BLACK WITH
BLACK STITCHING Similar to the AH-281 handle above, but 1-3/4 inches shorter. Handle
length is 6-13/16 inches (6.80"), center-to-center mounting distance is 6
inches (5.98") Black with black stitching, nickel mounts. Mounting
screws not included - use SC-402 or SC-403-4 screw pack. This is a great handle
to consider for smaller combo amps, practice amps, etc. Delivers a
professional quality look and reliability in a smaller size for smaller amps.
More details Part #AH-281-S
"Shorty"
$12.95
Click on photo for
larger view
Revisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, DARK BROWN WITH
BROWN STITCHING
Good replacement for Ampeg, Mesa Boogie, Randall™, Bogner, Ashdown, Rivera,
Blackstar, many others. Handle
length is 8 9/16 inches (8.57"), center-to-center mounting distance is 7 3/8
inches (7.38") Dark brown with brown stitching, nickel mounts.
More details Mounting
screws not included - use SC-402 or SC-403-4 screw pack. Part #AH-270
$15.95
Click on photo for
larger view
Revisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE,
TAN WITH TAN STITCHING
Good replacement for Ampeg, Mesa Boogie, Randall™, Bogner, Ashdown, Rivera,
Blackstar, many others. Handle
length is 8 9/16 inches (8.57"), center-to-center mounting distance is 7 3/8
inches (7.38") Tan with tan stitching, nickel mounts.
More details Mounting
screws not included - use SC-402 or SC-403-4 screw pack. Part #AH-108
$23.95
Click on photo for
larger view
Revisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, DARK BROWN WITH
WHITE STITCHING
Good replacement for Ampeg, Mesa Boogie, Randall™, Bogner, Ashdown, Rivera,
Blackstar, many others. Handle
length is 8 9/16 inches (8.57"), center-to-center mounting distance is 7 3/8
inches (7.38") Dark brown with white stitching, nickel mounts.
More details Mounting
screws not included - use SC-402 or SC-403-4 screw pack. Part #AH-318
$23.95
Click on photo for
larger view
Revisit™ AMP HANDLE, VINTAGE LEATHER-LOOK STYLE, DEEP NAVY BLUE-GREY WITH
WHITE STITCHING
Good replacement for Ampeg, Mesa Boogie, Randall™, Bogner, Ashdown, Rivera,
Blackstar, many others. Handle
length is 8 9/16 inches (8.57"), center-to-center mounting distance is 7 3/8
inches (7.38") Dark navy blue-grey with white stitching, nickel mounts.
More details Mounting
screws not included - use SC-402 or SC-403-4 screw pack. Part #AH-319
$23.95
Click on photo for
larger view
Orange™
AMP BLACK GUITAR AMP HANDLE.
Black rubber handle strap, metal reinforced. Black
rubber caps.
Screws not included - recommend using the
SC-403B black 10-32
type screws along with a 10-32 T-Nut for secure mounting. See
diagram for handle dimensions and center-center screw distance.
Fits most Orange Amplifiers. Also fits some Markbass amplifiers.
Part #OAH-456
$10.99
Click on photo for
larger view
Revisit™ GUITAR AMP HANDLE
- BLACK.
Rugged rubber black handle strap, steel reinforced. Black metal caps. Screws not included - recommend using
our SC-403B Black 10-32 type screws along with a 10-32 T-Nut for secure mounting. Handle strap is 7/8"
wide. Designed for screw holes set 8 1/4 inches apart. Total length of handle when properly mounted is
10 1/4".
Part #GAH-1
$10.99
Click on photo for
larger view
Revisit™ BLACK GUITAR AMP HANDLE,
WITH HARDWARE.
Rugged rubber black handle strap, steel reinforced. Black metal caps.
Black 10-32 screws and T-Nut mounting hardware are included. Handle strap is 7/8"
wide. Designed for screw holes set 8 1/4 to 8 3/8 inches apart. Total length of handle when properly mounted is
10 1/4". Great replacement for the Budda Superdrive 30 (Series 1
only, pre-Peavey).
Part #GAH-271B
$11.99
Click on photo for
larger view
Revisit™
NICKEL/BLACK GUITAR AMP HANDLE
- NICKEL, WITH HARDWARE.
Rugged rubber black handle strap, steel reinforced. Polished
nickel metal caps.
10-32 screws and T-Nut mounting hardware are included. Handle strap is 7/8"
wide. Designed for screw holes set 8 1/4 inches apart. Total length of handle when properly mounted is
10 1/4".
Not recommended for Fender, as the screws are set too far apart for
Fender™ amp specifications.
Part #GAH-271C
$10.99
BLACK FENDER HANDLE
Click on photo for
larger view
ORIGINAL
BLACK Fender™ GUITAR AMP HANDLE.
Black amplifier handle with vinyl sleeve over steel strap and
one-screw mounting nickel-plated end caps. Includes mounting
hardware (two screws and T-nuts).
Introduced on Blonde, Brown, and Blackface™-era Fender™ amplifiers. Used
on 65 Twin Reverb™, 65 Deluxe Reverb™, 65 Super Reverb™, 65 Princeton
Reverb™, 64 Vibroverb Custom, Custom Vibrolux™, Vibro-King™ 212 Enclosure,
Blues Junior™, Pro Junior™, Acoustasonic™ Jr. DSP, Acoustasonic 30, Acoustasonic
SFX II, Bassman™ 25, Bassman 60, Jazzmaster Ultralight™ Enclosure, Princeton
650™, Cyber Champ™, Rumble™ 112, Rumble 2x8, Super-Sonic™ 100 Head, Super-Sonic
Twin, Super Champ™ X2/XD, and Bullet 15 DSP amplifier. Fits most vintage
and modern amplifiers. 7 3/4" center to center screw placement. 9 1/4" handle length without
end caps.Original Fender™ part number 0990947000.
Part #FAH-332
$17.99
BROWN FENDER HANDLE
Click on photo for
larger view
ORIGINAL
BROWN Fender™ GUITAR AMP HANDLE.
Brown amplifier handle with vinyl sleeve over steel strap and
one-screw mounting nickel-plated end caps. Includes mounting
hardware (two screws and T-nuts).
Introduced on some Blonde and Brownface-era Fender™ amplifiers. 7 3/4" center to center screw placement. 9 1/4" handle length without
end caps.Original Fender™ part number 0990944000.
Part #FAH-944
$16.99
Click on photo for
larger view
GUITAR AMP HANDLE - SIMILAR TO Fender™ HANDLE.
Black handle strap, metal reinforced. Nickel metal caps - may be used
as replacement for vintage
and reissue Fender™ amps. Handle strap is 7/8"
wide. Designed for screw holes set 7 3/4 inches apart.
Looks similar to the original Fender™ part number 0990947000. Screws and T-Nuts included.
Part #FAH-261
$8.49
Click on photo for
larger view
ORIGINAL 4-SCREW Fender™ GUITAR AMP HANDLE.
Black handle strap, metal reinforced, with nickel-plated end caps - two screws in each end cap. Used on Cyber Twin, Cyber Twin SE, Cyber Deluxe, Stage™
series, Deluxe 90 DSP/900, Ultimate Chorus™, Princeton 65 DSP, 65 Twin Custom™,
94 (Evil) Twin™, "The Twin", Deluxe VM, Bandmaster VM Head, Steel King, Power Chorus, and
Bassman™ 300 amplifiers Includes
mounting screws and nuts.
Fender™ part number 0990948000. 8"
center to center. 9 1/4" handle length without end caps. Also fits
some some Music Man heads and combo amps.
Part #FAH-264
$19.95
Click on photo for
larger view
GENUINE
PEAVEY BLACK ENDS /BLACK STRAP GUITAR AMP HANDLE.
Black handle strap, metal reinforced. Black metal caps.
Screws and T-Nuts are NOT included. Screws and T-Nuts to fit are found
here. Handle strap is 7/8"
wide. Designed for screw holes set 7 3/4 inches apart. Total length of handle when properly mounted is 9
1/2 inches.
Part #PAH-301
$11.95
Click on photo for
larger view
GENUINE PEAVEY CHROME
ENDS /BLACK STRAP GUITAR AMP HANDLE.
Black handle strap, metal reinforced. Chrome metal caps. Screws
and T-Nuts are NOT included. Screws and T-Nuts to fit are found
here. Handle strap is 7/8"
wide. Designed for screw holes set 7-3/4 inches apart. Total length of handle when properly mounted is 9-1/2
inches.
Part #PAH-302
$10.95
(Black)
Click on photo for
larger view
Vox™ STYLE GUITAR AMP HANDLE.
Black handle strap, "dogbone" style, diamond pattern, with
brackets. Nickel end hooks - replacement for vintage
and modern Vox™ amps. Does
not contain Vox™ logo, so it may be used on other brands of amps. Center to
center measurement is 6 1/4 inches. Color of handle strap is
black. Screws not included - you might consider the pack of four SC-402 screws
found here. Note that some vintage
Vox™ amps
may have used a different thread type than the 8-32 thread of the SC-402 screws.
Part #VAH-327
$6.95
(Brown)
Click on photo for
larger view
Fender™ STYLE GUITAR AMP HANDLE.
Brown handle strap, "dogbone" style. Nickel end hooks - replacement for vintage
and modern Fender™ amps. Replacement for Fender™ part number 0990946000. Does
not contain Fender™ logo, so it may be used on other brands of amps. Used on vintage
and modern brownface and blonde tolex amps such as the 1959 Bassman, Hot Rod
Deluxe, Blues Deluxe, Blues Deville, Super-Sonic etc. Color of handle strap is
brown. Screws not included - order the pack of four SC-402 screws
found here.
Part #FAH-328
$7.99
(Black)
Click on photo for
larger view
Fender™ STYLE GUITAR AMP HANDLE.
Black handle strap, "dogbone" style. Nickel end hooks - replacement for vintage
and modern Fender™ amps. Replacement for Fender™ part number 0990943000. Does
not contain Fender™ logo, so it may be used on other brands of amps. Used on vintage
and modern black tolex amps such as the Hot Rod
Deville, Blues Deluxe, Blues Deville, Super-Sonic, etc. Color of handle strap is
black. Screws not included - order the pack of four
SC-402 screws found here.
Part #FAH-329
$7.99
Click on photo for
larger view
Fender™ "DOGBONE" HANDLE SCREWS
Pack of 4
nickel "Dogbone" handle screws for Fender™
style FAH-328 and FAH-329 handles. 8-32 thread. Fits the handle on the Fender™ Hot Rod Deluxe, Hot Rod Deville, Blues Deluxe, and Blues Deville, as well as other Fender™ amps of similar design. Also
works with Hiwatt handles and other British design amp handles. Part #SC-402
$1.59
(for a pack of 4 screws)
Click on photo for
larger view
Fender™ VINTAGE STYLE GUITAR AMP HANDLE,
RAISED, MEDIUM BROWN STITCHED SIMULATED LEATHER. Medium brown simulated leather handle strap, replacement for Fender™ "tweed" style amps (as
well as other vintage amps). Has slight "raised" bump near the center of the
handle. Medium brown, white stitched. 5-7/8" from post position
to post position, total length of strap when completely flat is 8-3/4". Comes complete with two
nickel-plated handle mounts and four screws. Part #GAH-282
$18.95
Click on photo for
larger view
Fender™ or Ampeg™ VINTAGE STYLE GUITAR AMP HANDLE, RAISED,
BLACK STITCHED
SIMULATED LEATHER.Black raised handle strap, made of simulated leather,
replacement for Fender™ "tweed" style amps or vintage Ampeg amps (as well as
other vintage amps). Has slight "raised" bump near the center of the handle.
Black, white stitched. 5-7/8" from post position to post position, total
length of strap when completely flat is 8-3/4". Mounts and screws
are included.
Part #GAH-782
$18.95
Click on photo for
larger view
HANDLE MOUNTING KIT - FOR STRAP HANDLES
Complete set of hardware for mounting one leather style strap handle. Works with our handles
GAH-282, GAH-782.
Part #THH-2
$4.95
Click on photo for
larger view
MARSHALL™
HANDLE STRAP FOR JCM900, JCM2000, ETC HEAD. Original Marshall™ handle strap for the
MAH-294 Handle. Sold
individually. Includes metal strap insert and rubber strap.
Genuine Marshall. Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Save money by replacing only the worn strap! Ends
and clamps not included.
Part #MHS-294
$7.95
(each)
Click on photo for
larger view
MARSHALL™ END CAPS FOR MAH-294 HANDLE.
Handle end caps for the MAH-294 Handle. Sold in sets of two caps. NOTE: DOES NOT HAVE THE MARSHALL LOGO ON THE CAPS.
Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Save money by replacing only the parts
the handle needs! Strap, screws and clamps not included. Set
of two end caps.
Part #MHC-294-2
$4.95
(for a set of 2 end caps)
Click on photo for
larger view
MARSHALL™ INTERNAL END CLAMPS FOR MAH-294 HANDLE.
Handle internal clamps for the MAH-294 Handle. Sold in sets of two end clamps.
Genuine Marshall.
Found primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Save money by replacing only the parts
the handle needs! Strap, black end caps, screws and strap not included.
Note: These are unfinished metal caps - designed to be used only
with the snap-on MHC-294-2 end caps. Set
of two end clamps.
Part #MIC-294-2
$2.99
(for a set of 2 end clamps)
Click on photo for
larger view
Marshall™
METRIC HANDLE SCREWS
Pack of 2 metric handle screws for Marshall™
MAH-294 handle. Original Marshall™ , designed to work with the OEM
metric T-Nuts. Set of 2 Flat-head counter-sunk Phillips,
M5 x 0.8, length 25 mm.
Found primarily on
JCM900, JCM2000, larger Valvestate, and JVM series amps.
Part #SC-404
$1.99
(for a pack of 2 Marshall™ metric screws)
Click on photos for
larger view
(Assembled)
Marshall™
HANDLE Genuine Marshall™ Handle for modern heads and combo amps. Used
primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Original Marshall™ part number M-PACK-00031. Kit contains:
(2) Countersunk screws - M5 x 0.8, overall
length of 25 mm
(2) Mounting brackets
(2) Black bracket covers with Marshall™
logo
(1) Rubber handle with metallic insert
Center-to-center screw mounting distance
is 8 3/8" (213mm).
Overall length of assembled and mounted
handle is 101/4"(260mm).
Replacement screws are the Marshall™ SC-404
screws, below
Part #MAH-294
$21.95
Click on photos for
larger view
(Assembled)
Marshall™
AFTERMARKET HANDLE Identical to the Genuine Marshall™ Handle MAH-294, except does not
have the "Marshall" name imprinted on the end caps. Save compared to the price of the original Marshall™ handle. For modern heads and combo amps. Used
primarily on JCM900, JCM2000, larger ValveState, and JVM series amps. Replaces Original Marshall™ part number M-PACK-00031
or stock number MAH-294. Kit contains:
(2) Countersunk screws - M5 x 0.8, overall
length of 25 mm
(2) Mounting brackets
(2) Black bracket covers (no Marshall™
logo)
(1) Rubber handle with metallic insert
Center-to-center screw mounting distance
is 8 3/8" (213mm).
Overall length of assembled and mounted
handle is 101/4"(260mm).
Replacement screws are the Marshall™ SC-404
screws, below
Part #RAH-294
$15.99
Click on photos for
larger view
VINTAGE
Revisit™ REISSUE
GOLD/BLACK HANDLE - Marshall™ JCM-800 style Marshall™ Handle for vintage heads and combo amps. Used
on some early JCM800 series. Kit contains:
(2) Mounting brackets
(2) Gold bracket covers
(1) Rubber handle strap with metallic insert
Center-to-center screw mounting distance
is 9 inches between the inside two screws, and 10 inches between the outside
two screws.
Overall length of assembled and mounted
handle is 11-1/4"(286mm).
Mounting screws are included.
Part #MAH-287
$19.99
Click on photos for
larger view
VINTAGE
Revisit™ REISSUE
SILVER/BLACK HANDLE - Marshall™ JCM-800 style Marshall™ Handle for vintage heads and combo amps. Used
on some early JCM800 series. Kit contains:
(2) Mounting brackets
(2) Silver color bracket covers
(1) Rubber handle strap with metallic insert,
silver ends
Center-to-center screw mounting distance
is 9 inches between the inside two screws, and 10 inches between the outside
two screws.
Overall length of assembled and mounted
handle is 11-1/4"(286mm).
Mounting screws are included.
Part #MAH-355
$19.99
Click on photos for
larger view
VINTAGE
Revisit™ REISSUE
GOLD/BLACK HANDLE REPLACEMENT STRAP - Marshall™ JCM-800 style The strap part only of handle part number MAH-287. Used on some
early Marshall™
JCM800 series amps. 11 inches, end-to-end.
Part #MHS-295
$13.95
Click on photos for
larger view
VINTAGE
Revisit™ REISSUE
GOLD HANDLE END CAP - Marshall™ JCM-800 style One end cap only of handle part number MAH-287. Used on some
early Marshall™
JCM800 series amps. Sold individually. Note: We
urge you to also replace the MIC-295 internal clamp at the same time.
These end caps may not lock securely on old internal clamps, making the end caps
randomly pop off when lifting the amp by its handle.
Part #MHC-295
$1.95
(for one end cap)
Click on photos for
larger view
VINTAGE
Revisit™ REISSUE
HANDLE INTERNAL CLAMP - Marshall™ JCM-800 style One internal clamp only of handle part numbers MAH-287 or MAH-355. Used on some
early Marshall™
JCM800 series amps. Sold individually.
Part #MIC-295
$1.60
(for one clamp)
Click on photos for
larger view
VINTAGE
Revisit REISSUE GOLD/BLACK HANDLE - JMP, JTM "PLEXI" Handle for vintage Marshall™ heads and combo amps. Replacement for
the original Marshall™ JMP, JTM "Plexi" series. Kit contains:
(2) Mounting brackets
(2) Gold bracket covers
(1) Rubber handle strap with metallic insert
Center-to-center screw mounting distance
is 9".
Overall length of assembled and mounted
handle is 10.7"(272mm).
Mounting screws are NOT included
Part #MAH-288
$23.95
Click on photo for
larger view
Choose from Black, Tan, or Havana
Brown
Mesa/Boogie™ AMP HANDLE, HEAVY-DUTY STITCHED Original Mesa/Boogie™
replacement handle. Handle
length is 8 9/16 inches (8.57"), center-to-center mounting distance is 7 3/8
inches (7.38"). Vintage Leather-look style. Available
colors: Black with black stitching, tan with tan stitching, Havana Brown
with white stitching. Nickel mounts.
More details Mounting
screws not included - use SC-403 screw pack. Choose handle color
in 'Select Color' box.
Part # MBH-X
$16.95
Click on photo for
larger view
Choose from Black or Nickel End Caps
& Screws
Mesa/Boogie™ AMP STRAP HANDLE KIT WITH
SCREWS,
NICKEL OR BLACK END CAPS Original
Mesa/Boogie™
replacement handle with hardware included.
Rugged rubber black handle strap, steel reinforced. Your choice of polished chrome
or black oxide metal caps with matching screws. Handle strap is 7/8"
wide. Designed for screw holes set 8 1/4 inches apart. Total length of handle when properly mounted is
10 1/4". Screws are 10-32 thread. Choose
end cap and screw color
in 'Select Color' box.
Part # MBH-271-X
$12.95
Click on photo for
larger view
NICKEL GLIDE FEET,
Revisit™, PACK OF 4, SCREWS INCLUDED.
Nickel cover over rubber foot. 15/16" Diameter, 0.33" Tall.
Replacement for glides used
on many Fender™ amplifiers, including the blackface and silverface designs.
Set of 4, includes 7/8" wood screws. Replaces Fender™ part number 0993900000. Part #SG-239
$4.95
(pack of 4 with screws)
Click on photo for
larger view
GENUINE Fender™
SPHINX GLIDE FEET, PACK OF 4, SCREWS INCLUDED.
Set of four metal amplifier cabinet glide feet with
rubber bushings and mounting screws. 1-1/4" diameter.
Fender™ part number 0993900000.
Fits Cyber-Champ™, Stage™ 100/112SE, Ultimate Chorus,
Princeton 65 DSP/650, GE-112 Enclosure, Tone-Master™ Enclosures, Vibro-King™
212 Enclosure, Pro Reverb, Deluxe 90 DSP/900, Acoustasonic™ 30/SFX II,
Stage™ 1000/1600, Super-Sonic™ Series, Bassman™ Enclosures, Concert™, "The
Twin", 65 Twin Custom™ 15, Steel King™, Hot Rod Deluxe™ Enclosures, Cyber
Deluxe, and Cyber-Twin™ amplifiers.
Fits most vintage and modern Fender™
amplifiers, but is larger than the traditional 1" diameter glide on
most blackface and silverface amps.
Part #SG-939
$12.99
(pack of 4 with screws)
Click on photo for
larger view
NICKEL GLIDE FEET, Fender™ STYLE, PACK OF 4,
3 PRONG HAMMER TYPE.
Older style 3-prong glide feet for Fender™
amplifiers - metal cap has 3 prongs, and the cap is hammered into the base of
the amplifier.
Part #CG-068
$3.95
(pack of 4)
Click on photo for
larger view
MARSHALL™
SPRUNG FOOT FOR HEADS. Original Marshall™ Sprung foot. Sold
individually. Screws are included 3 1/4" Long, 2" Wide, 1" Tall.
2-5/16" Mounting Centers.
Part #MSF-252
$8.95
(each)
Click on photo for
larger view
MARSHALL™ ANTI-SKID TRAY FOR 1960A ANGLED CABINETS. Genuine Marshall™
Anti-Skid Tray. Sold
individually. For the Marshall™ 1960A slant cabinets. Gold rivets are included. 9-7/8" Long, 3" Wide, 1/8" Thick.
With Marshall™
logo.
Part #AST-1960
$18.65
(each)
These have been on order from Marshall
since September 2023. They do not have them.
Click on photo for
larger view
MARSHALL™
CASTER CUPS FOR 1960B STRAIGHT CABINETS - SET OF 4. Genuine Marshall™
Caster Cups. Complete set of 4 for one cabinet. Package of 4 includes
16 gold rivets. For the Marshall™ 1960B straight cabinets. 3.9" Long,
2.07" Wide.
Part #MCC-1960
$18.95
(Set of 4)
Click on photo for
larger view
SMALL BLACK RUBBER FEET, SET OF 4
This 4-pack of heavy-duty rubber feet offers a sure grip
on all types of surfaces. Ideal for smaller amps, amp heads, effects units,
larger floor effects pedals, or speaker
cabinets. The integral metal washer in the mounting hole helps prevent
mounting screw "break-through" and adds overall durability.
0.84"
diameter x 0.31" high. Screws not included. Set of 4
feet. Part #BRF-750
$4.95
(pack of 4)
Click on photo for
larger view
SMALL BLACK RUBBER FEET, SET OF 4.
This heavy-duty rubber foot offers a sure grip
on all types of surfaces. Ideal for smaller amps, amp heads, or speaker
cabinets. The integral metal washer in the mounting hole helps prevent
mounting screw "break-through" and adds overall durability.
Just under 1 inch - 15/16"
diameter at the top, rounded down to 5/8" diameter at the bottom, and 3/8"
tall. Screws not included. Set of 4
feet. Part #BRF-723
$4.95
(pack of 4)
Click on photo for
larger view
MEDIUM BLACK RUBBER FEET, SET OF 4
This heavy-duty rubber foot offers a sure grip
on all types of surfaces. Ideal for large rack cabinets or speaker cabinets.
the integral metal washer in the mounting hole helps prevent mounting screw
"break-through" and adds overall durability. 1" diameter x 1" tall. Mounting
screws not included.
Part #BRF-1691
$4.95
(pack of 4)
Click on photo for
larger view
MEDIUM BLACK TAPERED RUBBER FEET, SET OF 4
This heavy-duty rubber foot offers a sure grip
on all types of surfaces. Ideal for rack-mount amps, combo amps, or small speaker cabinets.
The integral metal washer in the mounting hole helps prevent mounting screw
"break-through" and adds overall durability. 1" diameter
(wide end) x 3/4" diameter (narrow end) x 0.85" tall. Mounting
screws not included. Set of 4 feet.
Part #BRF-9105
$4.95
(pack of 4)
Click on photo for
larger view
MEDIUM BLACK RUBBER FEET, SET OF 4.
This heavy-duty rubber foot offers a sure grip
on all types of surfaces. Ideal for amp heads, combo amps, or smaller speaker cabinets.
The integral metal washer in the mounting hole helps prevent mounting screw
"break-through" and adds overall durability. 1" diameter x
5/8" tall. Mounting
screws not included. Part #BRF-1692
$4.95
(pack of 4)
Click on photo for
larger view
MEDIUM BLACK RUBBER FEET, SET OF 4.
Tapered: 1 3/16" diameter at small end,
1 1/4" diameter at large end. 1/2" tall. Black rubber with metal insert. Used to
support effects, amps, mixers. Mounting screws not included.
Part #BRF-9112
$4.95
(pack of 4)
Click on photo for
larger view
X-LARGE BLACK RUBBER FEET, SET OF 4. Tapered:
1 5/8" diameter at large end, 1 1/4" at small end. 3/4" tall. Black rubber with
metal insert. Used to support amp heads, speaker cabinets. Mounting screws not
included. Part #BRF-9107
$7.95
(pack of 4)
Click on photo for
larger view
Fender™ LARGE COMBO AMP COSMETIC REFURB KIT For original
1960s blackface and pre-1975 silverface Fender™ Twin Reverb, Super Reverb, Pro Amp, Pro
Reverb, Concert, Vibrosonic models which use 5 5/8" long chassis straps. (Not designed for the Blackface or Silverface REISSUES. NOT for
vintage Fender™ Speaker Cabinets or Heads, such as Bassman, Bandmaster, Showman,
Tremolux, etc. Not for the Bassman Ten Combo.)
Model not listed? - Contact us. Not for amps made after 1974,
not for reissued blackface and silverface amps. Contains original
Fender™ handle with mounting hardware, 5 5/8" chassis straps with bolts and keps
nuts,
nickel 15/16" glides, set of cabinet corners with mounting screws.
Spruce up the looks of your vintage amp! For additional
refurbishing, see the Fender™ logo plates here,
Fender™ knobs here, Fender™ lamp jewels
here and Fender™ casters
here
Part #FRK-5
$34.95
Click on photo for
larger view
Fender™ MEDIUM
COMBO AMP COSMETIC REFURB KIT For original
1960s blackface and pre-1975 silverface Fender™ Deluxe, Deluxe Reverb, Princeton,
Princeton Reverb, Tremolux, Musicmaster Bass, Vibrolux Reverb models which use 4 5/8" long chassis straps. (Not designed for the Blackface or Silverface REISSUES. NOT for
vintage Fender™ Speaker Cabinets or Heads, such as Bassman, Bandmaster, Showman,
Tremolux, etc. Not for the Bassman Ten Combo.)
Model not listed? - Contact us. Not for amps made after 1974,
not for reissued blackface and silverface amps. Contains original
Fender™ handle with mounting hardware, 4 5/8" chassis straps with bolts and keps
nuts,
nickel 15/16" glides, set of cabinet corners with mounting screws.
Spruce up the looks of your vintage amp! For additional
refurbishing, see the Fender™ logo plates here,
Fender™ knobs here, Fender™ lamp jewels
here and Fender™ casters
here
Part #FRK-4
$33.95
Click on photo for
larger view
Fender™ SMALL
COMBO AMP COSMETIC REFURB KIT For original
1960s and pre-1975 silverface Fender™ Champ, Vibro Champ, Bronco models which
use 3 5/8" long chassis straps.
Model not listed? - Contact us. Not for amps made after 1974,
not for reissued blackface and silverface amps. Contains original
Fender™ handle with mounting hardware, 3 5/8" chassis straps with bolts and keps
nuts,
nickel 15/16" glides.
Spruce up the looks of your vintage amp! For additional
refurbishing, see the Fender™ logo plates here,
Fender™ lamp jewels here and Fender™ knobs here
Part #FRK-3
$26.95
Click on photo for
larger view
LARGE SIZED STRAIN RELIEF FOR 35/64" X 5/8" HOLE Popular strain relief found on most
vintage
guitar amplifiers with round power cords, including most vintage Fender™ amps. Designed for 5/16" cord diameter (3 conductor 18ga power cable).
Click here for specific dimensions of chassis hole.
For a strain relief removal / installation tool to make the job much easier,
see the YTH-205 below. Part #SR-1200
$0.99
Click on photo for
larger view
EXTRA-LARGE SIZED STRAIN RELIEF FOR 3/4" X
27/32" HOLE
RATHER HUGE strain relief found on
a few
larger vintage power amplifiers with very thick power cords. Designed for 11/32" cord diameter.
Click here for specific dimensions of chassis hole. Not
for guitar amps!For a strain relief removal / installation tool to make the job much easier,
see the YTH-205 below. Part #SR-1300
$1.50
Click on photo for
larger view
STRAIN RELIEF INSTALLATION/REMOVAL TOOL
Removing and installing a strain relief can be a frustrating job.
Standard pliers just do not get the job done and can damage the strain relief.
These special strain relief pliers are just what you need. They fit
perfectly on the AC power cord strain relief and give you the leverage you need to
compress the strain relief for easy removal and installation, without damage. Part #YTH-205
$14.95
Click on photo for
larger view
SMALL RUBBER CHASSIS GROMMET FOR 3/8 INCH
CHASSIS HOLE (GROMMET INNER HOLE 1/4 INCH) Chassis grommet, for
electrical insulation, wire protection and management, shock absorption, or
mechanical isolation. This grommet has a 1/4 inch diameter inner hole,
and mounts in a 3/8 inch chassis hole.
Full
datasheet here. Part #RCG-739
$0.49
each
Click on photo for
larger view
LARGE RUBBER CHASSIS GROMMET FOR 1/2" CHASSIS HOLE
(GROMMET INNER HOLE 3/8 INCH) Chassis grommet, for
electrical insulation, wire protection and management, shock absorption, or
mechanical isolation. This grommet has a 3/8 inch diameter inner hole,
and mounts in a 1/2 inch chassis hole.
Full
datasheet here. Part #RCG-745
$0.49
each
Click on photo for
larger view
Fender™ style
reverb or AC cable clamp. Used on Fender amps since the early 60s to
hold the reverb cable to the side of the cabinet. Clamp is 3/8"
diameter, comes with 3/4" screw for mounting. Also used in some amplifiers
to hold the AC cord to the cabinet wall. Fender part number 022941.
Works on many other brands of amplifiers as well.
Part #RCC-381
$0.99
Click on photo for
larger view
Capacitor cover for
Fender™ Twin Reverb and other full-size Fender™ silverface and blackface
amps, such as the Super Reverb, Pro Reverb, Bandmaster and Bassman heads. Mounting centers are 7" x 3.5" Measurements are 7 1/8" x 3
1/2" x 1 1/4". Original Fender™ part number 0037854000. Part #CC-170
$34.95
Click on photo for
larger view
OUTPUT MODULE FAN - Marshall™ MG SERIES AMPS -
PREMIUM TYPE (BALL BEARINGS), HIGH AIRFLOW, LOWER NOISE
Fits many of the Marshall™ MG100DFX, MG100HDFX, MG50DFX and the MG250DFX models. IMPORTANT
NOTE: Does NOT fit the MG50FX, MG100FX, or MG100HFX models -
these are the models with the large "MG" on the front panel. Check model
number carefully. Note: Check
size of the old fan. If the old fan is 2" x 2" x 3/8", this is the
correct fan. Some Marshall™ versions of the MG100DFX, MG100HDFX,
MG50DFX and the MG250DFX used a larger fan (2 3/8" x 2 3/8" x 1").
If your amp has the larger fan, order the OD6025-12, below. 12 volts DC, 1.10 Watts,
5000
RPM, 11.0 Cubic Feet/Minute Airflow, 26dBA Noise. Comes with 12" tinned leads - cut off and splice connector from original fan. Ratings: Reliability: A, Airflow: A,
Noise: A-, Price: B- Part #OD5010-12
Installation video for fan:
$23.95
Click on photo for
larger view
OUTPUT MODULE FAN - Marshall™ MG Series
PREMIUM TYPE (BALL BEARINGS), HIGH AIRFLOW, LOW NOISE
Fits some versions of the Marshall™ MG100DFX, MG100HDFX, MG50DFX and the MG250DFX models. IMPORTANT
NOTE: Does NOT fit the MG50FX, MG100FX, or MG100HFX models -
these are the models with the large "MG" on the front panel. Check model
number carefully. Note: Check
size of the old fan. If the old fan is 2 3/8" x 2 3/8" x 1", this is
the correct fan. Some Marshall™ versions of the MG100DFX, MG100HDFX,
MG50DFX and the MG250DFX used a smaller fan (2" x 2" x 3/8").
If your amp has the smaller fan, order the OD5010-12, above. 12 volts DC,
1.70 Watts, 3500
RPM, 18.0 Cubic Feet/Minute Airflow, 27dBA Noise. Comes with 12" tinned leads - cut off and splice connector from original fan. Ratings: Reliability: A, Airflow: A,
Noise: B, Price: B Part #OD6025-12
$19.95
Click on photo for
larger view
ECONOMY OUTPUT MODULE FAN - Marshall™ AVT SERIES AMPS.
SEALED SLEEVE BEARINGS
Fits only the Marshall™ AVT50, AVT100, AVT150 and AVT275 models. This is
the newer style 1cm thick version, which replaces the older style 2cm thick
type. 40mm x 40mm x 10mm. 24 volts DC, 1.4 Watts, 6000 RPM, 6 CF/M Airflow,
25dBA noise rating, sealed sleeve bearings. Comes with tinned leads - cut off and splice connector from original fan. Part #OD4010-24SS
$13.95
Click on photo for
larger view
QUIET PREMIUM OUTPUT MODULE FAN - Marshall™ AVT SERIES AMPS.
DUAL BALL BEARINGS Fits only the Marshall™ AVT50, AVT100, AVT150 and AVT275 models. This is
the newer style 1cm thick version, which replaces the older style 2cm thick
type. 40mm x 40mm x 10mm. 24 volts DC, 1.4 Watts, 4800 RPM, 6 CF/M Airflow,
20dBA noise rating, dual ball bearings. Comes with tinned leads - cut off and splice connector from original fan. Part #OD4010-24MB
$22.95
Click on photo for
larger view
TRACE ELLIOT FAN™ - 12V FAN FOR SM / SMX AMPS
Original Trace Elliot™ replacement fan for SM and SMX series amps which use a 12V
fan, such as the GP7SM250. 80mm x 80mm x 25mm (3-1/8" x 3-1/8" x
1"), 12 volts DC, 0.13 amps. Part #D08T12LWS
$13.95
Click on photo for
larger view
ThermoCool Fan.
80 x 25mm Sleeve Bearing 19 CFM.
Thermocool axial fans provide enhanced cooling for a variety of electronic
devices. Leading air flow technology is designed into every Thermocool product
resulting in reduced turbulence, low noise levels and a more energy efficient
product. Thermocool fans are ideal for use in computer systems, portable CD and
DVD players, stereo components, overhead projectors, laptop computers, and many
other electronic applications where circulation is a key concern.
Specifications: • Power: 100-125V
AC, 50-60 Hz • Sleeve bearing • Lead wire connection included • 0.13 amps • 2300 RPM •
27dB noise level • 19 CFM air flow • Dimensions: 80 mm (H) x 80 mm (W) x 25
mm (D)
[3 1/4" (H) x 3 1/4" (W) x 1" (D)] For use on
100-125VAC System only, as found in North America, Japan, etc. Part #G8025HAS
$17.95
Click on photo for
larger view
ThermoCool Fan.
120 x 25mm Sleeve Bearing 57 CFM.
Thermocool axial fans provide enhanced cooling for a variety of electronic
devices. Leading air flow technology is designed into every Thermocool product
resulting in reduced turbulence, low noise levels and a more energy efficient
product. Thermocool fans are ideal for use in computer systems, portable CD and
DVD players, stereo components, overhead projectors, laptop computers, and many
other electronic applications where circulation is a key concern.
For plug in wiring harness, order 25-0050 fan cord separately.
Specifications: • Power: 100-125V
AC, 50-60 Hz • Sleeve bearing • Terminal connection • 0. 20 amps • 2300 RPM •
39dB noise level • 57CFM air flow • Dimensions: 120 mm (H) x 120 mm (W) x 25
mm (D).
[4 3/4" (H) x 4 3/4" (W) x 1 " (D)] For use on
100-125VAC System only, as found in North America, Japan, etc. Part #G12025HAS
$24.95
Click on photo for
larger view
ThermoCool Fan.
120 x 38mm Ball Bearing 72 CFM.
This size is commonly found in Mesa-Boogie Mark series amps.
Thermocool axial fans provide enhanced cooling for a variety of electronic
devices. Leading air flow technology is designed into every Thermocool product
resulting in reduced turbulence, low noise levels and a more energy efficient
product. Thermocool fans are ideal for use in computer systems, portable CD and
DVD players, stereo components, overhead projectors, laptop computers, and many
other electronic applications where circulation is a key concern.
For plug in wiring harness, order 25-0050 fan cord separately. For use on
100-125VAC System only, as found in North America, Japan, etc. This
size commonly found in Mesa-Boogie Mark series amps.
Specifications: • Power:
100-125V
AC, 50-60 Hz • Ball bearing • Terminal connection • 0.22 amps • 2200 RPM • 39dB
noise level • 72CFM air flow • Dimensions: 120 mm (H) x 120 mm (W) x 38 mm
(D).
Ratings: Reliability: A, Airflow: A,
Noise: A-, Price: B-
[4 3/4" (H) x 4 3/4" (W) x 1 1/2" (D)] Part #G12038MAS
$26.95
Click on photo for
larger view
Standard 24" fan cord with 90° angled plug.
For use with 110~120 VAC cooling fans with .110" terminals; non-terminated
on opposite end. Great for use with G12038MAS fans, above. Part #25-0050
$3.59
Click on photo for
larger view
L-PAD FACE PLATE AND KNOB, for 3/8" diameter threaded bushing found on most L-Pad Level
controls. Face plate AND knob only! L-Pad ordered separately.
Fits many bass
cabinets including the SWR Goliath, Marcus Miller Golight 410, Workingman
8x10, Working Pro 2x10, Ampeg PN-210HLF, PN-410HLF, SVT-410HLF, SVT-610HLF,
SVT-810SPC, BXT210M,
BXT410HL4, PR-1528HE, PN-115HLF, PR-810H, PB-250, the Kustom G410H, the
Engl B115 as well as many others.
This is the face plate and knob only - L-PAD itself ordered separately.
Raised lettering in charcoal gray instead of white. 3 1/8 inches in
diameter, 7/8 inch depth into cabinet. Requires 2 inch diameter hole
for mounting. Screws not included.
Part #LFP-380
$4.50
8 Ohms
Click on photo for
larger view
L-PAD, 8 Ohms, 3/8" threaded bushing (3/8" long), with plate, knob and hardware.
May also be used with the LFP-380 face plate and knob. 8 ohms
- for use with 8 ohm speakers, horn drivers or tweeters.
L-pads adjust the relative volume of drivers connected to them by placing added
resistance in series and parallel, keeping impedance a constant 8 ohm load. This
L-pad is rated at 100 watts RMS, is designed to be used with 8 ohm loads,
features a 3/8" shaft length, and comes with mounting hardware. This
style of L-Pad is found on many popular bass cabinets to control the
horn/tweeter level. 2.5 inches in diameter, 1 inch thick.
Included face plate is 2 1/8" x 2 1/8".
Part #LPD-262
$19.95
16 Ohms
Click on photo for
larger view
L-PAD, 16 Ohms, 3/8" threaded bushing (3/8" long), with plate, knob and hardware.
May also be used with the LFP-380 face plate and knob. 16 ohms - for
use with 8 ohm speakers, horn drivers or tweeters.
L-pads adjust the relative volume of drivers connected to them by placing added
resistance in series and parallel, keeping impedance a constant 8 ohm load. This
L-pad is rated at 100 watts RMS, is designed to be used with 16 ohm loads,
features a 3/8" shaft length, and comes with mounting hardware. This
style of L-Pad is found on many popular bass cabinets to control the
horn/tweeter level. 2.5 inches in diameter, 1 inch thick.
Included face plate is 2 1/8" x 2 1/8".
Part #LPD-261
BALL
HEAD MESH GRILLE AND WINDSCREEN FOR SHURE™
Fender™
Amp Tweed Block Logo Revive the look of your vintage-style or modern
Fender™ amp with a genuine Fender™ amplifier logo.
Marshall™
LOGO, WHITE PLASTIC, 6" LONG
Vox™
BRASS VENT, VINTAGE STYLE Found on several vintage Vox™
amps from the 1960s, including the original AC15 and AC30. The vintage Vox™ amps
typically used 3 of these vents across the top of the cabinet. This
recreation from Tube Amp Doctor is hand-crafted in Germany to be a perfect match
for the original brass vents.
Measures 0.720" x 4.805" (122 x 18.3mm).
Sold individually. Special order, allow 3 business days.
INSULATING SHOULDER WASHER, FIBER
Mesa/Boogie™ Nickel Chassis Strap - Large (6"),
bright nickel finish. Single chassis strap, no screws. Screw spacing is 5.31 inches center-to-center, strap length is
6 inches
end-to-end.
Original Mesa/Boogie part number 407520. Sold individually -
ordering quantity of 1 delivers 1 strap.
Peavey™
Stainless Steel
Screw - 4 inches long, 10-24 thread. Used on a variety of vintage
Peavey amps which had chassis straps on top of the amp cabinet. Sold individually - ordering quantity of 1 delivers 1 screw.
Each amplifier requires a total of 4 screws. 
REPLACEMENT
HOUSING SCREWS FOR MXR™ PEDALS (MODERN VERSION)
housing screws for MXR™, Way Huge and
other pedals which use 6-32 x 1/2" screws, including pedals which use Bud or
Hammond style enclosures.
STAINLESS STEEL CHASSIS SCREWS WITH WASHERS,
Orange™ METRIC
STAINLESS STEEL CHASSIS SCREWS WITH WASHERS,
Trace Elliot™ METRIC
JACK
NUT/FERULE, CHROME, with BLACK PLASTIC BEZEL/WASHER - BRITISH CLIFF STYLE
Revisit™
Quality Reproduction of Marshall™ CORNERS, FRONT OF
CABINET 
Orange™
AMP BLACK GUITAR AMP HANDLE.
Black rubber handle strap, metal reinforced. Black
rubber caps.
Screws not included - recommend using the
SC-403B black 10-32
type screws along with a 10-32 T-Nut for secure mounting. See
diagram for handle dimensions and center-center screw distance.
Fits most Orange Amplifiers. Also fits some Markbass amplifiers.
Fender™ style
reverb or AC cable clamp. Used on Fender amps since the early 60s to
hold the reverb cable to the side of the cabinet. Clamp is 3/8"
diameter, comes with 3/4" screw for mounting. Also used in some amplifiers
to hold the AC cord to the cabinet wall. Fender part number 022941.
Works on many other brands of amplifiers as well.
Capacitor cover for
Fender™ Twin Reverb and other full-size Fender™ silverface and blackface
amps, such as the Super Reverb, Pro Reverb, Bandmaster and Bassman heads. Mounting centers are 7" x 3.5" Measurements are 7 1/8" x 3
1/2" x 1 1/4". Original Fender™ part number 0037854000.
WARNING: These products may contain chemicals known to the State of California to cause cancer and birth defects or other reproductive harm. 
